_b ? _a : _b; })
-
-char ssid[32];
-char password[] = "testing123";
-int wifi_secure_mode = 0;
-
-static const int pin = 2;
-
-// Structure holding the TCP connection information.
-struct espconn tcp_conn;
-// TCP specific protocol structure.
-esp_tcp tcp_proto;
-
-// interrupt communication on port 1338, UDP!
-struct espconn inter_conn;
-esp_udp inter_proto;
-
-uint32_t sendData[0x14] = {0};
-uint32_t recvData[0x40] = {0};
-
-static int ICACHE_FLASH_ATTR __spi_comm(char *dat, int len, uint32_t *recvData, int recvDataLen) {
- unsigned int length = 0;
-
- SpiData spiData;
-
- spiData.cmd = 2;
- spiData.cmdLen = 0;
- spiData.addr = NULL;
- spiData.addrLen = 0;
-
- // float boot pin
- gpio_output_set(0, 0, 0, (1 << 4));
-
- // manual CS pin
- gpio_output_set(0, (1 << 5), 0, 0);
- memset(sendData, 0xCC, 0x14);
-
- // wait for ST to respond to CS interrupt
- os_delay_us(50);
-
- // send request
- memcpy(((void*)sendData), dat, len);
- spiData.data = sendData;
- spiData.dataLen = 0x14;
- SPIMasterSendData(SpiNum_HSPI, &spiData);
-
- #define SPI_TIMEOUT 50000
- // give the ST time to be ready, up to 500ms
- int i;
- for (i = 0; (gpio_input_get() & (1 << 4)) && i < SPI_TIMEOUT; i++) {
- os_delay_us(10);
- system_soft_wdt_feed();
- }
-
- // TODO: handle this better
- if (i == SPI_TIMEOUT) {
- os_printf("ERROR: SPI receive failed\n");
- goto fail;
- }
-
- // blank out recvData
- memset(recvData, 0x00, 0x44);
-
- // receive the length
- spiData.data = recvData;
- spiData.dataLen = 4;
- if(SPIMasterRecvData(SpiNum_HSPI, &spiData) == -1) {
- // TODO: Handle gracefully. Maybe fail if len read fails?
- os_printf("SPI: Failed to recv length\n");
- goto fail;
- }
-
- length = recvData[0];
- if (length > 0x40) {
- os_printf("SPI: BAD LENGTH RECEIVED %x\n", length);
- length = 0;
- goto fail;
- }
-
- // got response, 0x40 works, 0x44 does not
- spiData.data = recvData+1;
- spiData.dataLen = (length+3)&(~3); // recvDataLen;
- if(SPIMasterRecvData(SpiNum_HSPI, &spiData) == -1) {
- // TODO: Handle gracefully. Maybe retry if payload failed.
- os_printf("SPI: Failed to recv payload\n");
- length = 0;
- goto fail;
- }
-
-fail:
- // clear CS
- gpio_output_set((1 << 5), 0, 0, 0);
-
- // set boot pin back
- gpio_output_set((1 << 4), 0, (1 << 4), 0);
-
- return length;
-}
-
-int ICACHE_FLASH_ATTR spi_comm(char *dat, int len, uint32_t *recvData, int recvDataLen) {
- // blink the led during SPI comm
- if (GPIO_REG_READ(GPIO_OUT_ADDRESS) & (1 << pin)) {
- // set gpio low
- gpio_output_set(0, (1 << pin), 0, 0);
- } else {
- // set gpio high
- gpio_output_set((1 << pin), 0, 0, 0);
- }
-
- return __spi_comm(dat, len, recvData, recvDataLen);
-}
-
-static void ICACHE_FLASH_ATTR tcp_rx_cb(void *arg, char *data, uint16_t len) {
- // nothing too big
- if (len > 0x14) return;
-
- // do the SPI comm
- spi_comm(data, len, recvData, 0x40);
-
- espconn_send(&tcp_conn, recvData, 0x44);
-}
-
-void ICACHE_FLASH_ATTR tcp_connect_cb(void *arg) {
- struct espconn *conn = (struct espconn *)arg;
- espconn_set_opt(&tcp_conn, ESPCONN_NODELAY);
- espconn_regist_recvcb(conn, tcp_rx_cb);
-}
-
-// must be 0x44, because we can fit 4 more
-uint8_t buf[0x44*0x10];
-int queue_send_len = -1;
-
-void ICACHE_FLASH_ATTR poll_can(void *arg) {
- uint8_t timerRecvData[0x44] = {0};
- int i = 0;
- int j;
-
- while (i < 0x40) {
- int len = spi_comm("\x01\x00\x00\x00", 4, timerRecvData, 0x40);
- if (len == 0) break;
- if (len > 0x40) { os_printf("SPI LENGTH ERROR!"); break; }
-
- // if it sends it, assume it's valid CAN
- for (j = 0; j < len; j += 0x10) {
- memcpy(buf + i*0x10, (timerRecvData+4)+j, 0x10);
- i++;
- }
- }
-
- if (i != 0) {
- int ret = espconn_sendto(&inter_conn, buf, i*0x10);
- if (ret != 0) {
- os_printf("send failed: %d\n", ret);
- queue_send_len = i*0x10;
- } else {
- queue_send_len = -1;
- }
- }
-}
-
-int udp_countdown = 0;
-
-static volatile os_timer_t udp_callback;
-void ICACHE_FLASH_ATTR udp_callback_func(void *arg) {
- if (queue_send_len == -1) {
- poll_can(NULL);
- } else {
- int ret = espconn_sendto(&inter_conn, buf, queue_send_len);
- if (ret == 0) {
- queue_send_len = -1;
- }
- }
- if (udp_countdown > 0) {
- os_timer_arm(&udp_callback, 5, 0);
- udp_countdown--;
- } else {
- os_printf("UDP timeout\n");
- }
-}
-
-void ICACHE_FLASH_ATTR inter_recv_cb(void *arg, char *pusrdata, unsigned short length) {
- remot_info *premot = NULL;
- if (espconn_get_connection_info(&inter_conn,&premot,0) == ESPCONN_OK) {
- inter_conn.proto.udp->remote_port = premot->remote_port;
- inter_conn.proto.udp->remote_ip[0] = premot->remote_ip[0];
- inter_conn.proto.udp->remote_ip[1] = premot->remote_ip[1];
- inter_conn.proto.udp->remote_ip[2] = premot->remote_ip[2];
- inter_conn.proto.udp->remote_ip[3] = premot->remote_ip[3];
-
-
- if (udp_countdown == 0) {
- os_printf("UDP recv\n");
- udp_countdown = 200*5;
-
- // start 5 second timer
- os_timer_disarm(&udp_callback);
- os_timer_setfn(&udp_callback, (os_timer_func_t *)udp_callback_func, NULL);
- os_timer_arm(&udp_callback, 5, 0);
- } else {
- udp_countdown = 200*5;
- }
- }
-}
-
-void ICACHE_FLASH_ATTR wifi_configure(int secure) {
- wifi_secure_mode = secure;
-
- // start wifi AP
- wifi_set_opmode(SOFTAP_MODE);
- struct softap_config config = {0};
- wifi_softap_get_config(&config);
- strcpy(config.ssid, ssid);
- if (wifi_secure_mode == 0) strcat(config.ssid, "-pair");
- strcpy(config.password, password);
- config.ssid_len = strlen(config.ssid);
- config.authmode = wifi_secure_mode ? AUTH_WPA2_PSK : AUTH_OPEN;
- config.beacon_interval = 100;
- config.max_connection = 4;
- wifi_softap_set_config(&config);
-
- if (wifi_secure_mode) {
- // setup tcp server
- tcp_proto.local_port = 1337;
- tcp_conn.type = ESPCONN_TCP;
- tcp_conn.state = ESPCONN_NONE;
- tcp_conn.proto.tcp = &tcp_proto;
- espconn_regist_connectcb(&tcp_conn, tcp_connect_cb);
- espconn_accept(&tcp_conn);
- espconn_regist_time(&tcp_conn, 60, 0); // 60s timeout for all connections
-
- // setup inter server
- inter_proto.local_port = 1338;
- const char udp_remote_ip[4] = {255, 255, 255, 255};
- os_memcpy(inter_proto.remote_ip, udp_remote_ip, 4);
- inter_proto.remote_port = 1338;
-
- inter_conn.type = ESPCONN_UDP;
- inter_conn.proto.udp = &inter_proto;
-
- espconn_regist_recvcb(&inter_conn, inter_recv_cb);
- espconn_create(&inter_conn);
- }
-}
-
-void ICACHE_FLASH_ATTR wifi_init() {
- // default ssid and password
- memset(ssid, 0, 32);
- os_sprintf(ssid, "panda-%08x-BROKEN", system_get_chip_id());
-
- // fetch secure ssid and password
- // update, try 20 times, for 1 second
- for (int i = 0; i < 20; i++) {
- uint8_t digest[SHA_DIGEST_SIZE];
- char resp[0x20];
- __spi_comm("\x00\x00\x00\x00\x40\xD0\x00\x00\x00\x00\x20\x00", 0xC, recvData, 0x40);
- memcpy(resp, recvData+1, 0x20);
-
- SHA_hash(resp, 0x1C, digest);
- if (memcmp(digest, resp+0x1C, 4) == 0) {
- // OTP is valid
- memcpy(ssid+6, resp, 0x10);
- memcpy(password, resp+0x10, 10);
- break;
- }
- os_delay_us(50000);
- }
- os_printf("Finished getting SID\n");
- os_printf(ssid);
- os_printf("\n");
-
- // set IP
- wifi_softap_dhcps_stop(); //stop DHCP before setting static IP
- struct ip_info ip_config;
- IP4_ADDR(&ip_config.ip, 192, 168, 0, 10);
- IP4_ADDR(&ip_config.gw, 0, 0, 0, 0);
- IP4_ADDR(&ip_config.netmask, 255, 255, 255, 0);
- wifi_set_ip_info(SOFTAP_IF, &ip_config);
- int stupid_gateway = 0;
- wifi_softap_set_dhcps_offer_option(OFFER_ROUTER, &stupid_gateway);
- wifi_softap_dhcps_start();
-
- wifi_configure(0);
-}
-
-#define LOOP_PRIO 2
-#define QUEUE_SIZE 1
-static os_event_t my_queue[QUEUE_SIZE];
-void loop();
-
-void ICACHE_FLASH_ATTR web_init();
-void ICACHE_FLASH_ATTR elm327_init();
-
-void ICACHE_FLASH_ATTR user_init() {
- // init gpio subsystem
- gpio_init();
-
- // configure UART TXD to be GPIO1, set as output
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_U0TXD_U, FUNC_GPIO1);
- gpio_output_set(0, 0, (1 << pin), 0);
-
- // configure SPI
- SpiAttr hSpiAttr;
- hSpiAttr.bitOrder = SpiBitOrder_MSBFirst;
- hSpiAttr.speed = SpiSpeed_10MHz;
- hSpiAttr.mode = SpiMode_Master;
- hSpiAttr.subMode = SpiSubMode_0;
-
- // TODO: is one of these CS?
- WRITE_PERI_REG(PERIPHS_IO_MUX, 0x105);
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTDI_U, 2); // configure io to spi mode
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTCK_U, 2); // configure io to spi mode
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTMS_U, 2); // configure io to spi mode
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_MTDO_U, 2); // configure io to spi mode
- SPIInit(SpiNum_HSPI, &hSpiAttr);
- //SPICsPinSelect(SpiNum_HSPI, SpiPinCS_1);
-
- // configure UART TXD to be GPIO1, set as output
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO5_U, FUNC_GPIO5);
- gpio_output_set(0, 0, (1 << 5), 0);
- gpio_output_set((1 << 5), 0, 0, 0);
-
- // uart init
- uart_init(BIT_RATE_115200, BIT_RATE_115200);
-
- // led init
- PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO2_U, FUNC_GPIO2);
- gpio_output_set(0, (1 << pin), (1 << pin), 0);
-
- os_printf("hello\n");
-
- // needs SPI
- wifi_init();
-
- // support ota upgrades
- elm327_init();
- web_init();
-
- // set gpio high, so LED is off by default
- for (int i = 0; i < 5; i++) {
- gpio_output_set(0, (1 << pin), 0, 0);
- os_delay_us(50000);
- gpio_output_set((1 << pin), 0, 0, 0);
- os_delay_us(50000);
- }
-
- // jump to OS
- system_os_task(loop, LOOP_PRIO, my_queue, QUEUE_SIZE);
- system_os_post(LOOP_PRIO, 0, 0);
-}
-
-void ICACHE_FLASH_ATTR loop(os_event_t *events) {
- system_os_post(LOOP_PRIO, 0, 0);
-}
-
diff --git a/panda/boardesp/user_config.h b/panda/boardesp/user_config.h
deleted file mode 100644
index e69de29bb..000000000
diff --git a/panda/boardesp/webserver.c b/panda/boardesp/webserver.c
deleted file mode 100644
index 9266b08f7..000000000
--- a/panda/boardesp/webserver.c
+++ /dev/null
@@ -1,381 +0,0 @@
-#include "stdlib.h"
-#include "ets_sys.h"
-#include "osapi.h"
-#include "gpio.h"
-#include "mem.h"
-#include "os_type.h"
-#include "user_interface.h"
-#include "espconn.h"
-#include "upgrade.h"
-
-#include "crypto/rsa.h"
-#include "crypto/sha.h"
-
-#include "obj/gitversion.h"
-#include "obj/cert.h"
-
-#define max(a,b) ((a) > (b) ? (a) : (b))
-#define min(a,b) ((a) < (b) ? (a) : (b))
-#define espconn_send_string(conn, x) espconn_send(conn, x, strlen(x))
-
-#define MAX_RESP 0x800
-char resp[MAX_RESP];
-char pageheader[] = "HTTP/1.0 200 OK\nContent-Type: text/html\n\n"
-"\n"
-"\n"
-"\n"
-"Panda \n"
-"\n"
-"\n"
-"This is your comma.ai panda\n\n"
-"It's open source. Find the code here \n"
-"Designed to work with our dashcam, chffr \n";
-
-char pagefooter[] = " \n"
-"\n"
-"\n";
-
-char OK_header[] = "HTTP/1.0 200 OK\nContent-Type: text/html\n\n";
-
-static struct espconn web_conn;
-static esp_tcp web_proto;
-extern char ssid[];
-extern int wifi_secure_mode;
-
-char *st_firmware;
-int real_content_length, content_length = 0;
-char *st_firmware_ptr;
-LOCAL os_timer_t ota_reboot_timer;
-
-#define FIRMWARE_SIZE 503808
-
-typedef struct {
- uint16_t ep;
- uint16_t extra_len;
- union {
- struct {
- uint8_t request_type;
- uint8_t request;
- uint16_t value;
- uint16_t index;
- uint16_t length;
- } control;
- uint8_t data[0x10];
- } u;
-} usb_msg;
-
-int ICACHE_FLASH_ATTR usb_cmd(int ep, int len, int request,
- int value, int index, char *data) {
- usb_msg usb = {0};
-
- usb.ep = ep;
- usb.extra_len = (ep == 0) ? 0 : len;
- if (ep == 0) {
- usb.u.control.request_type = 0xc0;
- usb.u.control.request = request;
- usb.u.control.value = value;
- usb.u.control.index = index;
- } else {
- memcpy(&usb.u.data, data, usb.extra_len);
- }
-
- uint32_t recv[0x44/4];
- spi_comm(&usb, sizeof(usb), recv, 0x40);
-
- return recv[0];
-}
-
-
-void ICACHE_FLASH_ATTR st_flash() {
- if (st_firmware != NULL) {
- // boot mode
- os_printf("st_flash: enter boot mode\n");
- st_set_boot_mode(1);
-
- // echo
- os_printf("st_flash: wait for echo\n");
- for (int i = 0; i < 10; i++) {
- os_printf(" attempt: %d\n", i);
- if (usb_cmd(0, 0, 0xb0, 0, 0, NULL) > 0) break;
- }
-
- // unlock flash
- os_printf("st_flash: unlock flash\n");
- usb_cmd(0, 0, 0xb1, 0, 0, NULL);
-
- // erase sector 1
- os_printf("st_flash: erase sector 1\n");
- usb_cmd(0, 0, 0xb2, 1, 0, NULL);
-
- if (real_content_length >= 16384) {
- // erase sector 2
- os_printf("st_flash: erase sector 2\n");
- usb_cmd(0, 0, 0xb2, 2, 0, NULL);
- }
-
- // real content length will always be 0x10 aligned
- os_printf("st_flash: flashing\n");
- for (int i = 0; i < real_content_length; i += 0x10) {
- int rl = min(0x10, real_content_length-i);
- usb_cmd(2, rl, 0, 0, 0, &st_firmware[i]);
- system_soft_wdt_feed();
- }
-
- // reboot into normal mode
- os_printf("st_flash: rebooting\n");
- usb_cmd(0, 0, 0xd8, 0, 0, NULL);
-
- // done with this
- os_free(st_firmware);
- st_firmware = NULL;
- }
-}
-
-typedef enum {
- NOT_STARTED,
- CONNECTION_ESTABLISHED,
- RECEIVING_HEADER,
- RECEIVING_ST_FIRMWARE,
- RECEIVING_ESP_FIRMWARE,
- REBOOTING,
- ERROR
-} web_state_t;
-
-web_state_t state = NOT_STARTED;
-int esp_address, esp_address_erase_limit, start_address;
-
-void ICACHE_FLASH_ATTR hexdump(char *data, int len) {
- int i;
- for (i=0;isecure it");
- }
-
- ets_strcat(resp,"\nSet USB Mode:"
- "Client "
- "CDP "
- "DCP \n");
-
- ets_strcat(resp, pagefooter);
-
- espconn_send_string(&web_conn, resp);
- espconn_disconnect(conn);
- } else if (memcmp(data, "GET /secure", 11) == 0 && !wifi_secure_mode) {
- wifi_configure(1);
- } else if (memcmp(data, "GET /set_property?usb_mode=", 27) == 0 && wifi_secure_mode) {
- char mode_value = data[27] - '0';
- if (mode_value >= '\x00' && mode_value <= '\x02') {
- memset(resp, 0, MAX_RESP);
- char set_usb_mode_packet[] = "\x00\x00\x00\x00\x40\xE6\x00\x00\x00\x00\x40\x00";
- set_usb_mode_packet[6] = mode_value;
- uint32_t recvData[1];
- spi_comm(set_usb_mode_packet, 0xC, recvData, 0);
- os_sprintf(resp, "%sUSB Mode set to %02x\n\n", OK_header, mode_value);
- espconn_send_string(&web_conn, resp);
- espconn_disconnect(conn);
- }
- } else if (memcmp(data, "PUT /stupdate ", 14) == 0 && wifi_secure_mode) {
- os_printf("init st firmware\n");
- char *cl = strstr(data, "Content-Length: ");
- if (cl != NULL) {
- // get content length
- cl += strlen("Content-Length: ");
- content_length = skip_atoi(&cl);
- os_printf("with content length %d\n", content_length);
-
- // should be small enough to fit in RAM
- real_content_length = (content_length+0xF)&(~0xF);
- st_firmware_ptr = st_firmware = os_malloc(real_content_length);
- memset(st_firmware, 0, real_content_length);
- state = RECEIVING_ST_FIRMWARE;
- }
-
- } else if (((memcmp(data, "PUT /espupdate1 ", 16) == 0) ||
- (memcmp(data, "PUT /espupdate2 ", 16) == 0)) && wifi_secure_mode) {
- // 0x1000 = user1.bin
- // 0x81000 = user2.bin
- // 0x3FE000 = blank.bin
- os_printf("init esp firmware\n");
- char *cl = strstr(data, "Content-Length: ");
- if (cl != NULL) {
- // get content length
- cl += strlen("Content-Length: ");
- content_length = skip_atoi(&cl);
- os_printf("with content length %d\n", content_length);
-
- // setup flashing
- uint8_t current = system_upgrade_userbin_check();
- if (data[14] == '2' && current == UPGRADE_FW_BIN1) {
- os_printf("flashing boot2.bin\n");
- state = RECEIVING_ESP_FIRMWARE;
- esp_address = 4*1024 + FIRMWARE_SIZE + 16*1024 + 4*1024;
- } else if (data[14] == '1' && current == UPGRADE_FW_BIN2) {
- os_printf("flashing boot1.bin\n");
- state = RECEIVING_ESP_FIRMWARE;
- esp_address = 4*1024;
- } else {
- espconn_send_string(&web_conn, "HTTP/1.0 404 Not Found\nContent-Type: text/html\n\nwrong!\n");
- espconn_disconnect(conn);
- }
- esp_address_erase_limit = esp_address;
- start_address = esp_address;
- }
- } else {
- espconn_send_string(&web_conn, "HTTP/1.0 404 Not Found\nContent-Type: text/html\n\n404 Not Found!\n");
- espconn_disconnect(conn);
- }
- } else if (state == RECEIVING_ST_FIRMWARE) {
- os_printf("receiving st firmware: %d/%d\n", len, content_length);
- memcpy(st_firmware_ptr, data, min(content_length, len));
- st_firmware_ptr += len;
- content_length -= len;
-
- if (content_length <= 0 && real_content_length > 1000) {
- state = NOT_STARTED;
- os_printf("done!\n");
- espconn_send_string(&web_conn, "HTTP/1.0 200 OK\nContent-Type: text/html\n\nsuccess!\n");
- espconn_disconnect(conn);
-
- // reboot
- os_printf("Scheduling st_flash in 100ms.\n");
- os_timer_disarm(&ota_reboot_timer);
- os_timer_setfn(&ota_reboot_timer, (os_timer_func_t *)st_flash, NULL);
- os_timer_arm(&ota_reboot_timer, 100, 0);
- }
- } else if (state == RECEIVING_ESP_FIRMWARE) {
- if ((esp_address+len) < (start_address + FIRMWARE_SIZE)) {
- os_printf("receiving esp firmware: %d/%d -- 0x%x - 0x%x\n", len, content_length,
- esp_address, esp_address_erase_limit);
- content_length -= len;
- while (esp_address_erase_limit < (esp_address + len)) {
- os_printf("erasing 0x%X\n", esp_address_erase_limit);
- spi_flash_erase_sector(esp_address_erase_limit / SPI_FLASH_SEC_SIZE);
- esp_address_erase_limit += SPI_FLASH_SEC_SIZE;
- }
- SpiFlashOpResult res = spi_flash_write(esp_address, data, len);
- if (res != SPI_FLASH_RESULT_OK) {
- os_printf("flash fail @ 0x%x\n", esp_address);
- }
- esp_address += len;
-
- if (content_length == 0) {
-
- char digest[SHA_DIGEST_SIZE];
- uint32_t rsa[RSANUMBYTES/4];
- uint32_t dat[0x80/4];
- int ll;
- spi_flash_read(esp_address-RSANUMBYTES, rsa, RSANUMBYTES);
-
- // 32-bit aligned accesses only
- SHA_CTX ctx;
- SHA_init(&ctx);
- for (ll = start_address; ll < esp_address-RSANUMBYTES; ll += 0x80) {
- spi_flash_read(ll, dat, 0x80);
- SHA_update(&ctx, dat, min((esp_address-RSANUMBYTES)-ll, 0x80));
- }
- memcpy(digest, SHA_final(&ctx), SHA_DIGEST_SIZE);
-
- if (RSA_verify(&releaseesp_rsa_key, rsa, RSANUMBYTES, digest, SHA_DIGEST_SIZE) ||
- #ifdef ALLOW_DEBUG
- RSA_verify(&debugesp_rsa_key, rsa, RSANUMBYTES, digest, SHA_DIGEST_SIZE)
- #else
- false
- #endif
- ) {
- os_printf("RSA verify success!\n");
- espconn_send_string(&web_conn, "HTTP/1.0 200 OK\nContent-Type: text/html\n\nsuccess!\n");
- system_upgrade_flag_set(UPGRADE_FLAG_FINISH);
-
- // reboot
- os_printf("Scheduling reboot.\n");
- os_timer_disarm(&ota_reboot_timer);
- os_timer_setfn(&ota_reboot_timer, (os_timer_func_t *)system_upgrade_reboot, NULL);
- os_timer_arm(&ota_reboot_timer, 2000, 0);
- } else {
- os_printf("RSA verify FAILURE\n");
- espconn_send_string(&web_conn, "HTTP/1.0 500 Internal Server Error\nContent-Type: text/html\n\nrsa verify fail\n");
- }
- espconn_disconnect(conn);
- }
- }
- }
-}
-
-void ICACHE_FLASH_ATTR web_tcp_connect_cb(void *arg) {
- state = CONNECTION_ESTABLISHED;
- struct espconn *conn = (struct espconn *)arg;
- espconn_set_opt(&web_conn, ESPCONN_NODELAY);
- espconn_regist_recvcb(conn, web_rx_cb);
-}
-
-void ICACHE_FLASH_ATTR web_init() {
- web_proto.local_port = 80;
- web_conn.type = ESPCONN_TCP;
- web_conn.state = ESPCONN_NONE;
- web_conn.proto.tcp = &web_proto;
- espconn_regist_connectcb(&web_conn, web_tcp_connect_cb);
- espconn_accept(&web_conn);
-}
-
diff --git a/panda/buy.png b/panda/buy.png
deleted file mode 100644
index a4a9e0fd4..000000000
Binary files a/panda/buy.png and /dev/null differ
diff --git a/panda/certs/debug b/panda/certs/debug
deleted file mode 100644
index 39864b6b1..000000000
--- a/panda/certs/debug
+++ /dev/null
@@ -1,15 +0,0 @@
------BEGIN RSA PRIVATE KEY-----
-MIICXQIBAAKBgQC948lnRo4x44Rd7Y8bQAML4aKDC4XRx958fHV8K6+FbCaP1Z42
-U2kX0yygak0LjoDutpgObmGHZA+Iz3HeUD6VGjr/teN24vPk+A95cRsjt8rgmGQ9
-6HNjaNgjR+gl1F9XxFimMzir82Xpl1ekTueJNXa7ia5HVH1nFdiksOKHGQIDAQAB
-AoGAQuPw2I6EHJLW1/eNB75e1FqhUqRGeYV8nEGDaUBCTi+wzc4kM2LijF/5QnDv
-vvht9qkfm0XK2VSoHDtnEzcVM/l1ksb68n4R/1nUooAWY6cQI7dCSk/A6yS1EJFg
-BXsgGbT/65khw9pzBW2zVtMVcVNWFayqfCO1I9WcDdA1x1kCQQDfrhoZTZNoDEUE
-JKM4fiUdWr1h3Aw8KLJFFexSWeGDwo+qqnujYcKWkHa9qaH1RG5x8Kir9s9Oi4Js
-mzKwov8fAkEA2VPJPWxJ4vVQpXle6wC1nyoL7s739yxMWFcabvkzDDhlIVBNdVJd
-gZKsFWV7QnVNdDMjn9D27FwKu3i2D+kKxwJBANp1SMojqO765MEKI1t+YDNONx6H
-cm+i85Fjuv4nCIjOEdCGVuCYDxtMFpxgO2y3HAMuHx5sm8XDnWsDHLvFRdMCQD7V
-XqWHnYUk8AAnqy2+ssQl3/VXmZG5GQmhhV74Za3u0C5ljT+SZL6FrYMyKAT67T3f
-WzllrT6BDglNyTWoZxkCQQCt0XSoGM3603GGYNt6AUlGSgtXSo/2Px7odGUtQoKA
-FH9q6FVMYpQJ38spZxIGufZJmLP8LLg6YIWJj1F+akxr
------END RSA PRIVATE KEY-----
diff --git a/panda/certs/debug.pub b/panda/certs/debug.pub
deleted file mode 100644
index 00e219d7b..000000000
--- a/panda/certs/debug.pub
+++ /dev/null
@@ -1 +0,0 @@
-ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQC948lnRo4x44Rd7Y8bQAML4aKDC4XRx958fHV8K6+FbCaP1Z42U2kX0yygak0LjoDutpgObmGHZA+Iz3HeUD6VGjr/teN24vPk+A95cRsjt8rgmGQ96HNjaNgjR+gl1F9XxFimMzir82Xpl1ekTueJNXa7ia5HVH1nFdiksOKHGQ== batman@y840
diff --git a/panda/certs/debugesp b/panda/certs/debugesp
deleted file mode 100644
index 789beaac1..000000000
--- a/panda/certs/debugesp
+++ /dev/null
@@ -1,15 +0,0 @@
------BEGIN RSA PRIVATE KEY-----
-MIICXAIBAAKBgQCjIHvrSCWN0Nec6ozbImYik30PIF7JSWgdwDKTxSJ05RM3pj5E
-LQEGt3qcaVrTokO68tpt5Gu1p6ZsNqWg7iVTW9M7Qj7IH45YDzQP/PSRjgSosQA6
-6f5Gokba5QrW38myqimvj+0p+YH+CNGCBRlTUQGCO8uLCspMZneRSLPW9QIDAQAB
-AoGADaUn+HRef9BaWMvd4G6uMHI54cwJYbj8NpDfKjExQqnuw5bqWnWRQmiSnwbJ
-DC7kj3zE/LBAuj890ot3q1CAWqh47ZICZfoX9Qbi5TpvIHFCGy6YkOliF6iIQhR2
-4+zNKTAA0zNKskOM25PdI+grK1Ni/bEofSA6TrqvEwsmxnkCQQDVp9FUUor2Bo/h
-/3oAIP51LTw7vfpztYbJr+BDV63czV2DLXzSwzeNrwH4sA3oy1mjUgMBBgAarNGE
-DYlc4H5jAkEAw3UCHzzXPlxkw2QGp7nBly5y3p80Uqc31NuYz8rdX/U8KTngi2No
-Ft/SGCEXNpeYbToj+WK3RJJ2Ey0mK8+IxwJAcpGd/5CPsaQNLcw4WK9Yo+8Q2Jxk
-G/4gfDCSmqn+smNxnLEcuUwzkwdgkEGgA9BfjeOhdsAH+EXpx90WZrZ/LwJBAK0k
-jq+rTqUQZbZsejTEKYjJ/bnV4BzDwoKN0Q1pkLc7X4LJoW74rTFuLgdv8MdMfRtt
-IIb/eoeFEpGkMicnHesCQHgR7BTUGBM6Uxam7RCdsgVsxoHBma21E/44ivWUMZzN
-3oVt0mPnjS4speOlqwED5pCJ7yw7jwLPFMs8kNxuIKU=
------END RSA PRIVATE KEY-----
diff --git a/panda/certs/debugesp.pub b/panda/certs/debugesp.pub
deleted file mode 100644
index 3afcf3988..000000000
--- a/panda/certs/debugesp.pub
+++ /dev/null
@@ -1 +0,0 @@
-ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQCjIHvrSCWN0Nec6ozbImYik30PIF7JSWgdwDKTxSJ05RM3pj5ELQEGt3qcaVrTokO68tpt5Gu1p6ZsNqWg7iVTW9M7Qj7IH45YDzQP/PSRjgSosQA66f5Gokba5QrW38myqimvj+0p+YH+CNGCBRlTUQGCO8uLCspMZneRSLPW9Q== batman@y840
diff --git a/panda/certs/release.pub b/panda/certs/release.pub
deleted file mode 100644
index 19066e29a..000000000
--- a/panda/certs/release.pub
+++ /dev/null
@@ -1 +0,0 @@
-ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQDGN9GU2nOc0kKq6vdZI5qUMzHt234ngqofrgCFFxL0D2Whex0zACp9gar0HZp+bvtpoSgU/Ev8wexNKr+A9QTradljiuxi5ctrOra9k+wxqNj63Wrcu4+wU5UnJEVf/buV4jCOFffMT8z3PO4imt8LzHuEIC/m/ASKVYyvuvBRQQ== batman@y840
diff --git a/panda/certs/releaseesp.pub b/panda/certs/releaseesp.pub
deleted file mode 100644
index 1d1d54bb7..000000000
--- a/panda/certs/releaseesp.pub
+++ /dev/null
@@ -1 +0,0 @@
-ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgQDN4pVyGuJJSde1l3Fjay8qPxog09DsAJZtYPk+armoYO1L6YKReUTcMNyHQYZZMZFmhCdgjCgTIF2QYWMoP4KSe8l6JF04YPP51dIgefc6UXjtlSI8Pyutr0v9xXjSfsVm3RAJxDSHgzs9AoMsluKCL+LhAR1nd7cuHXITJ80O4w== batman@y840
diff --git a/panda/common/version.mk b/panda/common/version.mk
deleted file mode 100644
index cc66efaa6..000000000
--- a/panda/common/version.mk
+++ /dev/null
@@ -1,20 +0,0 @@
-ifeq ($(RELEASE),1)
- BUILD_TYPE = "RELEASE"
-else
- BUILD_TYPE = "DEBUG"
-endif
-
-SELF_DIR := $(dir $(lastword $(MAKEFILE_LIST)))
-
-ifneq ($(wildcard $(SELF_DIR)/../.git/HEAD),)
-obj/gitversion.h: $(SELF_DIR)/../VERSION $(SELF_DIR)/../.git/HEAD $(SELF_DIR)/../.git/index
- echo "const uint8_t gitversion[] = \"$(shell cat $(SELF_DIR)/../VERSION)-$(BUILDER)-$(shell git rev-parse --short=8 HEAD)-$(BUILD_TYPE)\";" > $@
-else
-ifneq ($(wildcard $(SELF_DIR)/../../.git/modules/panda/HEAD),)
-obj/gitversion.h: $(SELF_DIR)/../VERSION $(SELF_DIR)/../../.git/modules/panda/HEAD $(SELF_DIR)/../../.git/modules/panda/index
- echo "const uint8_t gitversion[] = \"$(shell cat $(SELF_DIR)/../VERSION)-$(BUILDER)-$(shell git rev-parse --short=8 HEAD)-$(BUILD_TYPE)\";" > $@
-else
-obj/gitversion.h: $(SELF_DIR)/../VERSION
- echo "const uint8_t gitversion[] = \"$(shell cat $(SELF_DIR)/../VERSION)-$(BUILDER)-unknown-$(BUILD_TYPE)\";" > $@
-endif
-endif
diff --git a/panda/crypto/getcertheader.py b/panda/crypto/getcertheader.py
deleted file mode 100755
index 75d04e977..000000000
--- a/panda/crypto/getcertheader.py
+++ /dev/null
@@ -1,46 +0,0 @@
-#!/usr/bin/env python
-import sys
-import struct
-from Crypto.PublicKey import RSA
-
-def egcd(a, b):
- if a == 0:
- return (b, 0, 1)
- else:
- g, y, x = egcd(b % a, a)
- return (g, x - (b // a) * y, y)
-
-def modinv(a, m):
- g, x, y = egcd(a, m)
- if g != 1:
- raise Exception('modular inverse does not exist')
- else:
- return x % m
-
-def to_c_string(x):
- mod = (hex(x)[2:-1].rjust(0x100, '0'))
- hh = ''.join('\\x'+mod[i:i+2] for i in range(0, 0x100, 2))
- return hh
-
-def to_c_uint32(x):
- nums = []
- for i in range(0x20):
- nums.append(x%(2**32))
- x /= (2**32)
- return "{"+'U,'.join(map(str, nums))+"U}"
-
-for fn in sys.argv[1:]:
- rsa = RSA.importKey(open(fn).read())
- rr = pow(2**1024, 2, rsa.n)
- n0inv = 2**32 - modinv(rsa.n, 2**32)
-
- cname = fn.split("/")[-1].split(".")[0] + "_rsa_key"
-
- print 'RSAPublicKey '+cname+' = {.len = 0x20,'
- print ' .n0inv = %dU,' % n0inv
- print ' .n = %s,' % to_c_uint32(rsa.n)
- print ' .rr = %s,' % to_c_uint32(rr)
- print ' .exponent = %d,' % rsa.e
- print '};'
-
-
diff --git a/panda/crypto/hash-internal.h b/panda/crypto/hash-internal.h
deleted file mode 100644
index 05ec3ec9f..000000000
--- a/panda/crypto/hash-internal.h
+++ /dev/null
@@ -1,63 +0,0 @@
-/*
- * Copyright 2007 The Android Open Source Project
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * * Neither the name of Google Inc. nor the names of its contributors may
- * be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY Google Inc. ``AS IS'' AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
- * EVENT SHALL Google Inc. BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
- * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
- * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
- * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
- * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-
-#ifndef SYSTEM_CORE_INCLUDE_MINCRYPT_HASH_INTERNAL_H_
-#define SYSTEM_CORE_INCLUDE_MINCRYPT_HASH_INTERNAL_H_
-
-#include "stdint.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif // __cplusplus
-
-struct HASH_CTX; // forward decl
-
-typedef struct HASH_VTAB {
- void (* const init)(struct HASH_CTX*);
- void (* const update)(struct HASH_CTX*, const void*, int);
- const uint8_t* (* const final)(struct HASH_CTX*);
- const uint8_t* (* const hash)(const void*, int, uint8_t*);
- int size;
-} HASH_VTAB;
-
-typedef struct HASH_CTX {
- const HASH_VTAB * f;
- uint64_t count;
- uint8_t buf[64];
- uint32_t state[8]; // upto SHA2
-} HASH_CTX;
-
-#define HASH_init(ctx) (ctx)->f->init(ctx)
-#define HASH_update(ctx, data, len) (ctx)->f->update(ctx, data, len)
-#define HASH_final(ctx) (ctx)->f->final(ctx)
-#define HASH_hash(data, len, digest) (ctx)->f->hash(data, len, digest)
-#define HASH_size(ctx) (ctx)->f->size
-
-#ifdef __cplusplus
-}
-#endif // __cplusplus
-
-#endif // SYSTEM_CORE_INCLUDE_MINCRYPT_HASH_INTERNAL_H_
diff --git a/panda/crypto/rsa.c b/panda/crypto/rsa.c
deleted file mode 100644
index 24171e879..000000000
--- a/panda/crypto/rsa.c
+++ /dev/null
@@ -1,294 +0,0 @@
-/* rsa.c
-**
-** Copyright 2012, The Android Open Source Project
-**
-** Redistribution and use in source and binary forms, with or without
-** modification, are permitted provided that the following conditions are met:
-** * Redistributions of source code must retain the above copyright
-** notice, this list of conditions and the following disclaimer.
-** * Redistributions in binary form must reproduce the above copyright
-** notice, this list of conditions and the following disclaimer in the
-** documentation and/or other materials provided with the distribution.
-** * Neither the name of Google Inc. nor the names of its contributors may
-** be used to endorse or promote products derived from this software
-** without specific prior written permission.
-**
-** THIS SOFTWARE IS PROVIDED BY Google Inc. ``AS IS'' AND ANY EXPRESS OR
-** IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
-** MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
-** EVENT SHALL Google Inc. BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
-** SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
-** PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
-** OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
-** WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
-** OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
-** ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-*/
-
-#include "rsa.h"
-#include "sha.h"
-
-// a[] -= mod
-static void subM(const RSAPublicKey* key,
- uint32_t* a) {
- int64_t A = 0;
- int i;
- for (i = 0; i < key->len; ++i) {
- A += (uint64_t)a[i] - key->n[i];
- a[i] = (uint32_t)A;
- A >>= 32;
- }
-}
-
-// return a[] >= mod
-static int geM(const RSAPublicKey* key,
- const uint32_t* a) {
- int i;
- for (i = key->len; i;) {
- --i;
- if (a[i] < key->n[i]) return 0;
- if (a[i] > key->n[i]) return 1;
- }
- return 1; // equal
-}
-
-// montgomery c[] += a * b[] / R % mod
-static void montMulAdd(const RSAPublicKey* key,
- uint32_t* c,
- const uint32_t a,
- const uint32_t* b) {
- uint64_t A = (uint64_t)a * b[0] + c[0];
- uint32_t d0 = (uint32_t)A * key->n0inv;
- uint64_t B = (uint64_t)d0 * key->n[0] + (uint32_t)A;
- int i;
-
- for (i = 1; i < key->len; ++i) {
- A = (A >> 32) + (uint64_t)a * b[i] + c[i];
- B = (B >> 32) + (uint64_t)d0 * key->n[i] + (uint32_t)A;
- c[i - 1] = (uint32_t)B;
- }
-
- A = (A >> 32) + (B >> 32);
-
- c[i - 1] = (uint32_t)A;
-
- if (A >> 32) {
- subM(key, c);
- }
-}
-
-// montgomery c[] = a[] * b[] / R % mod
-static void montMul(const RSAPublicKey* key,
- uint32_t* c,
- const uint32_t* a,
- const uint32_t* b) {
- int i;
- for (i = 0; i < key->len; ++i) {
- c[i] = 0;
- }
- for (i = 0; i < key->len; ++i) {
- montMulAdd(key, c, a[i], b);
- }
-}
-
-// In-place public exponentiation.
-// Input and output big-endian byte array in inout.
-static void modpow(const RSAPublicKey* key,
- uint8_t* inout) {
- uint32_t a[RSANUMWORDS];
- uint32_t aR[RSANUMWORDS];
- uint32_t aaR[RSANUMWORDS];
- uint32_t* aaa = 0;
- int i;
-
- // Convert from big endian byte array to little endian word array.
- for (i = 0; i < key->len; ++i) {
- uint32_t tmp =
- (inout[((key->len - 1 - i) * 4) + 0] << 24) |
- (inout[((key->len - 1 - i) * 4) + 1] << 16) |
- (inout[((key->len - 1 - i) * 4) + 2] << 8) |
- (inout[((key->len - 1 - i) * 4) + 3] << 0);
- a[i] = tmp;
- }
-
- if (key->exponent == 65537) {
- aaa = aaR; // Re-use location.
- montMul(key, aR, a, key->rr); // aR = a * RR / R mod M
- for (i = 0; i < 16; i += 2) {
- montMul(key, aaR, aR, aR); // aaR = aR * aR / R mod M
- montMul(key, aR, aaR, aaR); // aR = aaR * aaR / R mod M
- }
- montMul(key, aaa, aR, a); // aaa = aR * a / R mod M
- } else if (key->exponent == 3) {
- aaa = aR; // Re-use location.
- montMul(key, aR, a, key->rr); /* aR = a * RR / R mod M */
- montMul(key, aaR, aR, aR); /* aaR = aR * aR / R mod M */
- montMul(key, aaa, aaR, a); /* aaa = aaR * a / R mod M */
- }
-
- // Make sure aaa < mod; aaa is at most 1x mod too large.
- if (geM(key, aaa)) {
- subM(key, aaa);
- }
-
- // Convert to bigendian byte array
- for (i = key->len - 1; i >= 0; --i) {
- uint32_t tmp = aaa[i];
- *inout++ = tmp >> 24;
- *inout++ = tmp >> 16;
- *inout++ = tmp >> 8;
- *inout++ = tmp >> 0;
- }
-}
-
-// Expected PKCS1.5 signature padding bytes, for a keytool RSA signature.
-// Has the 0-length optional parameter encoded in the ASN1 (as opposed to the
-// other flavor which omits the optional parameter entirely). This code does not
-// accept signatures without the optional parameter.
-
-/*
-static const uint8_t sha_padding[RSANUMBYTES] = {
- 0x00, 0x01, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0x00, 0x30, 0x21, 0x30,
- 0x09, 0x06, 0x05, 0x2b, 0x0e, 0x03, 0x02, 0x1a,
- 0x05, 0x00, 0x04, 0x14,
-
- // 20 bytes of hash go here.
- 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
-};
-*/
-
-static const uint8_t sha_padding_1024[RSANUMBYTES] = {
- 0x00, 0x01, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- 0xff, 0xff, 0xff, 0x00,
-
- // 20 bytes of hash go here.
- 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
-};
-
-// SHA-1 of PKCS1.5 signature sha_padding for 2048 bit, as above.
-// At the location of the bytes of the hash all 00 are hashed.
-/*static const uint8_t kExpectedPadShaRsa2048[SHA_DIGEST_SIZE] = {
- 0xdc, 0xbd, 0xbe, 0x42, 0xd5, 0xf5, 0xa7, 0x2e,
- 0x6e, 0xfc, 0xf5, 0x5d, 0xaf, 0x9d, 0xea, 0x68,
- 0x7c, 0xfb, 0xf1, 0x67
-};*/
-
-// Verify a 2048-bit RSA PKCS1.5 signature against an expected hash.
-// Both e=3 and e=65537 are supported. hash_len may be
-// SHA_DIGEST_SIZE (== 20) to indicate a SHA-1 hash, or
-// SHA256_DIGEST_SIZE (== 32) to indicate a SHA-256 hash. No other
-// values are supported.
-//
-// Returns 1 on successful verification, 0 on failure.
-int RSA_verify(const RSAPublicKey *key,
- const uint8_t *signature,
- const int len,
- const uint8_t *hash,
- const int hash_len) {
- uint8_t buf[RSANUMBYTES];
- int i;
- //const uint8_t* padding_hash;
-
- if (key->len != RSANUMWORDS) {
- return 0; // Wrong key passed in.
- }
-
- if (len != sizeof(buf)) {
- return 0; // Wrong input length.
- }
-
- if (hash_len != SHA_DIGEST_SIZE) {
- return 0; // Unsupported hash.
- }
-
- if (key->exponent != 3 && key->exponent != 65537) {
- return 0; // Unsupported exponent.
- }
-
- for (i = 0; i < len; ++i) { // Copy input to local workspace.
- buf[i] = signature[i];
- }
-
- modpow(key, buf); // In-place exponentiation.
-
-#ifdef TEST_RSA
- printf("sig\n");
- for (i=0;i> (32 - (bits))))
-
-static void SHA1_Transform(SHA_CTX* ctx) {
- uint32_t W[80];
- uint32_t A, B, C, D, E;
- uint8_t* p = ctx->buf;
- int t;
-
- for(t = 0; t < 16; ++t) {
- uint32_t tmp = *p++ << 24;
- tmp |= *p++ << 16;
- tmp |= *p++ << 8;
- tmp |= *p++;
- W[t] = tmp;
- }
-
- for(; t < 80; t++) {
- W[t] = rol(1,W[t-3] ^ W[t-8] ^ W[t-14] ^ W[t-16]);
- }
-
- A = ctx->state[0];
- B = ctx->state[1];
- C = ctx->state[2];
- D = ctx->state[3];
- E = ctx->state[4];
-
- for(t = 0; t < 80; t++) {
- uint32_t tmp = rol(5,A) + E + W[t];
-
- if (t < 20)
- tmp += (D^(B&(C^D))) + 0x5A827999;
- else if ( t < 40)
- tmp += (B^C^D) + 0x6ED9EBA1;
- else if ( t < 60)
- tmp += ((B&C)|(D&(B|C))) + 0x8F1BBCDC;
- else
- tmp += (B^C^D) + 0xCA62C1D6;
-
- E = D;
- D = C;
- C = rol(30,B);
- B = A;
- A = tmp;
- }
-
- ctx->state[0] += A;
- ctx->state[1] += B;
- ctx->state[2] += C;
- ctx->state[3] += D;
- ctx->state[4] += E;
-}
-
-static const HASH_VTAB SHA_VTAB = {
- SHA_init,
- SHA_update,
- SHA_final,
- SHA_hash,
- SHA_DIGEST_SIZE
-};
-
-void SHA_init(SHA_CTX* ctx) {
- ctx->f = &SHA_VTAB;
- ctx->state[0] = 0x67452301;
- ctx->state[1] = 0xEFCDAB89;
- ctx->state[2] = 0x98BADCFE;
- ctx->state[3] = 0x10325476;
- ctx->state[4] = 0xC3D2E1F0;
- ctx->count = 0;
-}
-
-
-void SHA_update(SHA_CTX* ctx, const void* data, int len) {
- int i = (int) (ctx->count & 63);
- const uint8_t* p = (const uint8_t*)data;
-
- ctx->count += len;
-
- while (len--) {
- ctx->buf[i++] = *p++;
- if (i == 64) {
- SHA1_Transform(ctx);
- i = 0;
- }
- }
-}
-
-
-const uint8_t* SHA_final(SHA_CTX* ctx) {
- uint8_t *p = ctx->buf;
- uint64_t cnt = ctx->count * 8;
- int i;
-
- SHA_update(ctx, (uint8_t*)"\x80", 1);
- while ((ctx->count & 63) != 56) {
- SHA_update(ctx, (uint8_t*)"\0", 1);
- }
-
- /* Hack - right shift operator with non const argument requires
- * libgcc.a which is missing in EON
- * thus expanding for loop from
-
- for (i = 0; i < 8; ++i) {
- uint8_t tmp = (uint8_t) (cnt >> ((7 - i) * 8));
- SHA_update(ctx, &tmp, 1);
- }
-
- to
- */
-
- uint8_t tmp = 0;
- tmp = (uint8_t) (cnt >> ((7 - 0) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 1) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 2) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 3) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 4) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 5) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 6) * 8));
- SHA_update(ctx, &tmp, 1);
- tmp = (uint8_t) (cnt >> ((7 - 7) * 8));
- SHA_update(ctx, &tmp, 1);
-
- for (i = 0; i < 5; i++) {
- uint32_t tmp = ctx->state[i];
- *p++ = tmp >> 24;
- *p++ = tmp >> 16;
- *p++ = tmp >> 8;
- *p++ = tmp >> 0;
- }
-
- return ctx->buf;
-}
-
-/* Convenience function */
-const uint8_t* SHA_hash(const void* data, int len, uint8_t* digest) {
- SHA_CTX ctx;
- SHA_init(&ctx);
- SHA_update(&ctx, data, len);
- memcpy(digest, SHA_final(&ctx), SHA_DIGEST_SIZE);
- return digest;
-}
diff --git a/panda/crypto/sha.h b/panda/crypto/sha.h
deleted file mode 100644
index 4b51a531b..000000000
--- a/panda/crypto/sha.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * Copyright 2005 The Android Open Source Project
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- * * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- * * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- * * Neither the name of Google Inc. nor the names of its contributors may
- * be used to endorse or promote products derived from this software
- * without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY Google Inc. ``AS IS'' AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
- * EVENT SHALL Google Inc. BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
- * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
- * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
- * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
- * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- */
-#ifndef SYSTEM_CORE_INCLUDE_MINCRYPT_SHA1_H_
-#define SYSTEM_CORE_INCLUDE_MINCRYPT_SHA1_H_
-
-#include "hash-internal.h"
-
-#ifdef __cplusplus
-extern "C" {
-#endif // __cplusplus
-
-typedef HASH_CTX SHA_CTX;
-
-void SHA_init(SHA_CTX* ctx);
-void SHA_update(SHA_CTX* ctx, const void* data, int len);
-const uint8_t* SHA_final(SHA_CTX* ctx);
-
-// Convenience method. Returns digest address.
-// NOTE: *digest needs to hold SHA_DIGEST_SIZE bytes.
-const uint8_t* SHA_hash(const void* data, int len, uint8_t* digest);
-
-#define SHA_DIGEST_SIZE 20
-
-#ifdef __cplusplus
-}
-#endif // __cplusplus
-
-#endif // SYSTEM_CORE_INCLUDE_MINCRYPT_SHA1_H_
diff --git a/panda/crypto/sign.py b/panda/crypto/sign.py
deleted file mode 100755
index 159299271..000000000
--- a/panda/crypto/sign.py
+++ /dev/null
@@ -1,29 +0,0 @@
-#!/usr/bin/env python
-import os
-import sys
-import struct
-import hashlib
-from Crypto.PublicKey import RSA
-
-rsa = RSA.importKey(open(sys.argv[3]).read())
-
-with open(sys.argv[1]) as f:
- dat = f.read()
-
-print "signing", len(dat), "bytes"
-
-with open(sys.argv[2], "wb") as f:
- if os.getenv("SETLEN") is not None:
- x = struct.pack("I", len(dat)) + dat[4:]
- # mock signature of dat[4:]
- dd = hashlib.sha1(dat[4:]).digest()
- else:
- x = dat
- dd = hashlib.sha1(dat).digest()
- print "hash:",dd.encode("hex")
- dd = "\x00\x01" + "\xff"*0x69 + "\x00" + dd
- rsa_out = pow(int(dd.encode("hex"), 16), rsa.d, rsa.n)
- sig = (hex(rsa_out)[2:-1].rjust(0x100, '0')).decode("hex")
- x += sig
- f.write(x)
-
diff --git a/panda/crypto/stdint.h b/panda/crypto/stdint.h
deleted file mode 100644
index 67ac93ed7..000000000
--- a/panda/crypto/stdint.h
+++ /dev/null
@@ -1,4 +0,0 @@
-#define uint8_t unsigned char
-#define uint32_t unsigned int
-#define int64_t long long
-#define uint64_t unsigned long long
diff --git a/panda/docs/guide.pdf b/panda/docs/guide.pdf
deleted file mode 100644
index 5dbc95680..000000000
Binary files a/panda/docs/guide.pdf and /dev/null differ
diff --git a/panda/drivers/linux/.gitignore b/panda/drivers/linux/.gitignore
deleted file mode 100644
index 93a6cde76..000000000
--- a/panda/drivers/linux/.gitignore
+++ /dev/null
@@ -1,6 +0,0 @@
-.*.cmd
-*.ko
-.tmp_versions
-Module.symvers
-modules.order
-*.mod.c
diff --git a/panda/drivers/linux/Makefile b/panda/drivers/linux/Makefile
deleted file mode 100644
index e5b1ec421..000000000
--- a/panda/drivers/linux/Makefile
+++ /dev/null
@@ -1,18 +0,0 @@
-VERSION=0.0.1
-obj-m+=panda.o
-
-link:
- sudo dkms add `pwd`
-
-build:
- sudo dkms build panda/$(VERSION)
-
-install:
- sudo dkms install panda/$(VERSION)
-
-all: build install
-
-uninstall:
- sudo dkms uninstall panda/$(VERSION)
- sudo dkms remove panda/$(VERSION) --all
-
diff --git a/panda/drivers/linux/README.md b/panda/drivers/linux/README.md
deleted file mode 100644
index 81e95523a..000000000
--- a/panda/drivers/linux/README.md
+++ /dev/null
@@ -1,19 +0,0 @@
-Installs the panda linux kernel driver using DKMS.
-
-This will allow the panda to work with tools such as `can-utils`
-
-prerequisites:
- - `apt-get install dkms gcc linux-headers-$(uname -r) make sudo`
-
-installation:
- - `make link` (only needed the first time. It will report an error on subsequent attempts to link)
- - `make all`
- - `make install`
-
-uninstall:
- - `make uninstall`
-
-usage:
-
-You will need to bring it up using `sudo ifconfig can0 up` or
-`sudo ip link set dev can0 up`, depending on your platform.
diff --git a/panda/drivers/linux/dkms.conf b/panda/drivers/linux/dkms.conf
deleted file mode 100644
index da9cba04a..000000000
--- a/panda/drivers/linux/dkms.conf
+++ /dev/null
@@ -1,6 +0,0 @@
-PACKAGE_NAME="panda"
-PACKAGE_VERSION="0.0.1"
-BUILT_MODULE_NAME[0]="panda"
-DEST_MODULE_LOCATION[0]="/kernel/drivers/net/panda/"
-AUTOINSTALL="yes"
-
diff --git a/panda/drivers/linux/panda.c b/panda/drivers/linux/panda.c
deleted file mode 100644
index 4c5980a9d..000000000
--- a/panda/drivers/linux/panda.c
+++ /dev/null
@@ -1,613 +0,0 @@
-/**
- * @file panda.c
- * @author Jessy Diamond Exum
- * @date 16 June 2017
- * @version 0.1
- * @brief Driver for the Comma.ai Panda CAN adapter to allow it to be controlled via
- * the Linux SocketCAN interface.
- * @see https://github.com/commaai/panda for the full project.
- * @see Inspired by net/can/usb/mcba_usb.c from Linux Kernel 4.12-rc4.
- */
-
-#include
-#include
-#include
-#include // Macros used to mark up functions e.g., __init __exit
-#include // Contains types, macros, functions for the kernel
-#include // Core header for loading LKMs into the kernel
-#include
-#include
-
-/* vendor and product id */
-#define PANDA_MODULE_NAME "panda"
-#define PANDA_VENDOR_ID 0XBBAA
-#define PANDA_PRODUCT_ID 0XDDCC
-
-#define PANDA_MAX_TX_URBS 20
-#define PANDA_CTX_FREE PANDA_MAX_TX_URBS
-
-#define PANDA_USB_RX_BUFF_SIZE 0x40
-#define PANDA_USB_TX_BUFF_SIZE (sizeof(struct panda_usb_can_msg))
-
-#define PANDA_NUM_CAN_INTERFACES 3
-
-#define PANDA_CAN_TRANSMIT 1
-#define PANDA_CAN_EXTENDED 4
-
-#define PANDA_BITRATE 500000
-
-#define PANDA_DLC_MASK 0x0F
-
-struct panda_usb_ctx {
- struct panda_inf_priv *priv;
- u32 ndx;
- u8 dlc;
-};
-
-struct panda_dev_priv;
-
-struct panda_inf_priv {
- struct can_priv can;
- struct panda_usb_ctx tx_context[PANDA_MAX_TX_URBS];
- struct net_device *netdev;
- struct usb_anchor tx_submitted;
- atomic_t free_ctx_cnt;
- u8 interface_num;
- u8 mcu_can_ifnum;
- struct panda_dev_priv *priv_dev;
-};
-
-struct panda_dev_priv {
- struct usb_device *udev;
- struct device *dev;
- struct usb_anchor rx_submitted;
- struct panda_inf_priv *interfaces[PANDA_NUM_CAN_INTERFACES];
-};
-
-struct __packed panda_usb_can_msg {
- u32 rir;
- u32 bus_dat_len;
- u8 data[8];
-};
-
-static const struct usb_device_id panda_usb_table[] = {
- { USB_DEVICE(PANDA_VENDOR_ID, PANDA_PRODUCT_ID) },
- {} /* Terminating entry */
-};
-
-MODULE_DEVICE_TABLE(usb, panda_usb_table);
-
-
-// panda: CAN1 = 0 CAN2 = 1 CAN3 = 4
-const int can_numbering[] = {0,1,4};
-
-struct panda_inf_priv *
-panda_get_inf_from_bus_id(struct panda_dev_priv *priv_dev, int bus_id){
- int inf_num;
- for(inf_num = 0; inf_num < PANDA_NUM_CAN_INTERFACES; inf_num++)
- if(can_numbering[inf_num] == bus_id)
- return priv_dev->interfaces[inf_num];
- return NULL;
-}
-
-// CTX handling shamlessly ripped from mcba_usb.c linux driver
-static inline void panda_init_ctx(struct panda_inf_priv *priv)
-{
- int i = 0;
-
- for (i = 0; i < PANDA_MAX_TX_URBS; i++) {
- priv->tx_context[i].ndx = PANDA_CTX_FREE;
- priv->tx_context[i].priv = priv;
- }
-
- atomic_set(&priv->free_ctx_cnt, ARRAY_SIZE(priv->tx_context));
-}
-
-static inline struct panda_usb_ctx *panda_usb_get_free_ctx(struct panda_inf_priv *priv,
- struct can_frame *cf)
-{
- int i = 0;
- struct panda_usb_ctx *ctx = NULL;
-
- for (i = 0; i < PANDA_MAX_TX_URBS; i++) {
- if (priv->tx_context[i].ndx == PANDA_CTX_FREE) {
- ctx = &priv->tx_context[i];
- ctx->ndx = i;
- ctx->dlc = cf->can_dlc;
-
- atomic_dec(&priv->free_ctx_cnt);
- break;
- }
- }
-
- printk("CTX num %d\n", atomic_read(&priv->free_ctx_cnt));
- if (!atomic_read(&priv->free_ctx_cnt)){
- /* That was the last free ctx. Slow down tx path */
- printk("SENDING TOO FAST\n");
- netif_stop_queue(priv->netdev);
- }
-
- return ctx;
-}
-
-/* panda_usb_free_ctx and panda_usb_get_free_ctx are executed by different
- * threads. The order of execution in below function is important.
- */
-static inline void panda_usb_free_ctx(struct panda_usb_ctx *ctx)
-{
- /* Increase number of free ctxs before freeing ctx */
- atomic_inc(&ctx->priv->free_ctx_cnt);
-
- ctx->ndx = PANDA_CTX_FREE;
-
- /* Wake up the queue once ctx is marked free */
- netif_wake_queue(ctx->priv->netdev);
-}
-
-
-
-static void panda_urb_unlink(struct panda_inf_priv *priv)
-{
- usb_kill_anchored_urbs(&priv->priv_dev->rx_submitted);
- usb_kill_anchored_urbs(&priv->tx_submitted);
-}
-
-static int panda_set_output_enable(struct panda_inf_priv* priv, bool enable){
- return usb_control_msg(priv->priv_dev->udev,
- usb_sndctrlpipe(priv->priv_dev->udev, 0),
- 0xDC, USB_TYPE_VENDOR | USB_RECIP_DEVICE,
- enable ? 0x1337 : 0, 0, NULL, 0, USB_CTRL_SET_TIMEOUT);
-}
-
-static void panda_usb_write_bulk_callback(struct urb *urb)
-{
- struct panda_usb_ctx *ctx = urb->context;
- struct net_device *netdev;
-
- WARN_ON(!ctx);
-
- netdev = ctx->priv->netdev;
-
- /* free up our allocated buffer */
- usb_free_coherent(urb->dev, urb->transfer_buffer_length,
- urb->transfer_buffer, urb->transfer_dma);
-
- if (!netif_device_present(netdev))
- return;
-
- netdev->stats.tx_packets++;
- netdev->stats.tx_bytes += ctx->dlc;
-
- can_get_echo_skb(netdev, ctx->ndx);
-
- if (urb->status)
- netdev_info(netdev, "Tx URB aborted (%d)\n", urb->status);
-
- /* Release the context */
- panda_usb_free_ctx(ctx);
-}
-
-
-static netdev_tx_t panda_usb_xmit(struct panda_inf_priv *priv,
- struct panda_usb_can_msg *usb_msg,
- struct panda_usb_ctx *ctx)
-{
- struct urb *urb;
- u8 *buf;
- int err;
-
- /* create a URB, and a buffer for it, and copy the data to the URB */
- urb = usb_alloc_urb(0, GFP_ATOMIC);
- if (!urb)
- return -ENOMEM;
-
- buf = usb_alloc_coherent(priv->priv_dev->udev,
- PANDA_USB_TX_BUFF_SIZE, GFP_ATOMIC,
- &urb->transfer_dma);
- if (!buf) {
- err = -ENOMEM;
- goto nomembuf;
- }
-
- memcpy(buf, usb_msg, PANDA_USB_TX_BUFF_SIZE);
-
- usb_fill_bulk_urb(urb, priv->priv_dev->udev,
- usb_sndbulkpipe(priv->priv_dev->udev, 3), buf,
- PANDA_USB_TX_BUFF_SIZE, panda_usb_write_bulk_callback,
- ctx);
-
- urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
- usb_anchor_urb(urb, &priv->tx_submitted);
-
- err = usb_submit_urb(urb, GFP_ATOMIC);
- if (unlikely(err))
- goto failed;
-
- /* Release our reference to this URB, the USB core will eventually free it entirely. */
- usb_free_urb(urb);
-
- return 0;
-
- failed:
- usb_unanchor_urb(urb);
- usb_free_coherent(priv->priv_dev->udev, PANDA_USB_TX_BUFF_SIZE, buf, urb->transfer_dma);
-
- if (err == -ENODEV)
- netif_device_detach(priv->netdev);
- else
- netdev_warn(priv->netdev, "failed tx_urb %d\n", err);
-
- nomembuf:
- usb_free_urb(urb);
-
- return err;
-}
-
-static void panda_usb_process_can_rx(struct panda_dev_priv *priv_dev,
- struct panda_usb_can_msg *msg)
-{
- struct can_frame *cf;
- struct sk_buff *skb;
- int bus_num;
- struct panda_inf_priv *priv_inf;
- struct net_device_stats *stats;
-
- bus_num = (msg->bus_dat_len >> 4) & 0xf;
- priv_inf = panda_get_inf_from_bus_id(priv_dev, bus_num);
- if(!priv_inf){
- printk("Got something on an unused interface %d\n", bus_num);
- return;
- }
- printk("Recv bus %d\n", bus_num);
-
- stats = &priv_inf->netdev->stats;
- //u16 sid;
-
- if (!netif_device_present(priv_inf->netdev))
- return;
-
- skb = alloc_can_skb(priv_inf->netdev, &cf);
- if (!skb)
- return;
-
- if(msg->rir & PANDA_CAN_EXTENDED){
- cf->can_id = (msg->rir >> 3) | CAN_EFF_FLAG;
- }else{
- cf->can_id = (msg->rir >> 21);
- }
-
- // TODO: Handle Remote Frames
- //if (msg->dlc & MCBA_DLC_RTR_MASK)
- // cf->can_id |= CAN_RTR_FLAG;
-
- cf->can_dlc = get_can_dlc(msg->bus_dat_len & PANDA_DLC_MASK);
-
- memcpy(cf->data, msg->data, cf->can_dlc);
-
- stats->rx_packets++;
- stats->rx_bytes += cf->can_dlc;
-
- netif_rx(skb);
-}
-
-static void panda_usb_read_int_callback(struct urb *urb)
-{
- struct panda_dev_priv *priv_dev = urb->context;
- int retval;
- int pos = 0;
- int inf_num;
-
- switch (urb->status) {
- case 0: /* success */
- break;
- case -ENOENT:
- case -ESHUTDOWN:
- return;
- default:
- dev_info(priv_dev->dev, "Rx URB aborted (%d)\n", urb->status);
- goto resubmit_urb;
- }
-
- while (pos < urb->actual_length) {
- struct panda_usb_can_msg *msg;
-
- if (pos + sizeof(struct panda_usb_can_msg) > urb->actual_length) {
- dev_err(priv_dev->dev, "format error\n");
- break;
- }
-
- msg = (struct panda_usb_can_msg *)(urb->transfer_buffer + pos);
-
- panda_usb_process_can_rx(priv_dev, msg);
-
- pos += sizeof(struct panda_usb_can_msg);
- }
-
- resubmit_urb:
- usb_fill_int_urb(urb, priv_dev->udev,
- usb_rcvintpipe(priv_dev->udev, 1),
- urb->transfer_buffer, PANDA_USB_RX_BUFF_SIZE,
- panda_usb_read_int_callback, priv_dev, 5);
-
- retval = usb_submit_urb(urb, GFP_ATOMIC);
-
- if (retval == -ENODEV){
- for(inf_num = 0; inf_num < PANDA_NUM_CAN_INTERFACES; inf_num++)
- if(priv_dev->interfaces[inf_num])
- netif_device_detach(priv_dev->interfaces[inf_num]->netdev);
- }else if (retval)
- dev_err(priv_dev->dev, "failed resubmitting read bulk urb: %d\n", retval);
-}
-
-
-static int panda_usb_start(struct panda_dev_priv *priv_dev)
-{
- int err;
- struct urb *urb = NULL;
- u8 *buf;
- int inf_num;
-
- for(inf_num = 0; inf_num < PANDA_NUM_CAN_INTERFACES; inf_num++)
- panda_init_ctx(priv_dev->interfaces[inf_num]);
-
- err = usb_set_interface(priv_dev->udev, 0, 1);
- if (err) {
- dev_err(priv_dev->dev, "Can not set alternate setting to 1, error: %i", err);
- return err;
- }
-
- /* create a URB, and a buffer for it */
- urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!urb) {
- return -ENOMEM;
- }
-
- buf = usb_alloc_coherent(priv_dev->udev, PANDA_USB_RX_BUFF_SIZE,
- GFP_KERNEL, &urb->transfer_dma);
- if (!buf) {
- dev_err(priv_dev->dev, "No memory left for USB buffer\n");
- usb_free_urb(urb);
- return -ENOMEM;
- }
-
- usb_fill_int_urb(urb, priv_dev->udev,
- usb_rcvintpipe(priv_dev->udev, 1),
- buf, PANDA_USB_RX_BUFF_SIZE,
- panda_usb_read_int_callback, priv_dev, 5);
- urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
-
- usb_anchor_urb(urb, &priv_dev->rx_submitted);
-
- err = usb_submit_urb(urb, GFP_KERNEL);
- if (err) {
- usb_unanchor_urb(urb);
- usb_free_coherent(priv_dev->udev, PANDA_USB_RX_BUFF_SIZE,
- buf, urb->transfer_dma);
- usb_free_urb(urb);
- dev_err(priv_dev->dev, "Failed in start, while submitting urb.\n");
- return err;
- }
-
- /* Drop reference, USB core will take care of freeing it */
- usb_free_urb(urb);
-
-
- return 0;
-}
-
-/* Open USB device */
-static int panda_usb_open(struct net_device *netdev)
-{
- struct panda_inf_priv *priv = netdev_priv(netdev);
- int err;
-
- /* common open */
- err = open_candev(netdev);
- if (err)
- return err;
-
- //priv->can_speed_check = true;
- priv->can.state = CAN_STATE_ERROR_ACTIVE;
-
- netif_start_queue(netdev);
-
- return 0;
-}
-
-/* Close USB device */
-static int panda_usb_close(struct net_device *netdev)
-{
- struct panda_inf_priv *priv = netdev_priv(netdev);
-
- priv->can.state = CAN_STATE_STOPPED;
-
- netif_stop_queue(netdev);
-
- /* Stop polling */
- panda_urb_unlink(priv);
-
- close_candev(netdev);
-
- return 0;
-}
-
-static netdev_tx_t panda_usb_start_xmit(struct sk_buff *skb,
- struct net_device *netdev)
-{
- struct panda_inf_priv *priv_inf = netdev_priv(netdev);
- struct can_frame *cf = (struct can_frame *)skb->data;
- struct panda_usb_ctx *ctx = NULL;
- struct net_device_stats *stats = &priv_inf->netdev->stats;
- int err;
- struct panda_usb_can_msg usb_msg = {};
- int bus = priv_inf->mcu_can_ifnum;
-
- if (can_dropped_invalid_skb(netdev, skb)){
- printk("Invalid CAN packet");
- return NETDEV_TX_OK;
- }
-
- ctx = panda_usb_get_free_ctx(priv_inf, cf);
-
- //Warning: cargo cult. Can't tell what this is for, but it is
- //everywhere and encouraged in the documentation.
- can_put_echo_skb(skb, priv_inf->netdev, ctx->ndx);
-
- if(cf->can_id & CAN_EFF_FLAG){
- usb_msg.rir = cpu_to_le32(((cf->can_id & 0x1FFFFFFF) << 3) |
- PANDA_CAN_TRANSMIT | PANDA_CAN_EXTENDED);
- }else{
- usb_msg.rir = cpu_to_le32(((cf->can_id & 0x7FF) << 21) | PANDA_CAN_TRANSMIT);
- }
- usb_msg.bus_dat_len = cpu_to_le32((cf->can_dlc & 0x0F) | (bus << 4));
-
- memcpy(usb_msg.data, cf->data, cf->can_dlc);
-
- //TODO Handle Remote Frames
- //if (cf->can_id & CAN_RTR_FLAG)
- // usb_msg.dlc |= PANDA_DLC_RTR_MASK;
-
- netdev_err(netdev, "Received data from socket. canid: %x; len: %d\n", cf->can_id, cf->can_dlc);
-
- err = panda_usb_xmit(priv_inf, &usb_msg, ctx);
- if (err)
- goto xmit_failed;
-
- return NETDEV_TX_OK;
-
- xmit_failed:
- can_free_echo_skb(priv_inf->netdev, ctx->ndx);
- panda_usb_free_ctx(ctx);
- dev_kfree_skb(skb);
- stats->tx_dropped++;
-
- return NETDEV_TX_OK;
-}
-
-static const struct net_device_ops panda_netdev_ops = {
- .ndo_open = panda_usb_open,
- .ndo_stop = panda_usb_close,
- .ndo_start_xmit = panda_usb_start_xmit,
-};
-
-static int panda_usb_probe(struct usb_interface *intf,
- const struct usb_device_id *id)
-{
- struct net_device *netdev;
- struct panda_inf_priv *priv_inf;
- int err = -ENOMEM;
- int inf_num;
- struct panda_dev_priv *priv_dev;
- struct usb_device *usbdev = interface_to_usbdev(intf);
-
- priv_dev = kzalloc(sizeof(struct panda_dev_priv), GFP_KERNEL);
- if (!priv_dev) {
- dev_err(&intf->dev, "Couldn't alloc priv_dev\n");
- return -ENOMEM;
- }
- priv_dev->udev = usbdev;
- priv_dev->dev = &intf->dev;
- usb_set_intfdata(intf, priv_dev);
-
- ////// Interface privs
- for(inf_num = 0; inf_num < PANDA_NUM_CAN_INTERFACES; inf_num++){
- netdev = alloc_candev(sizeof(struct panda_inf_priv), PANDA_MAX_TX_URBS);
- if (!netdev) {
- dev_err(&intf->dev, "Couldn't alloc candev\n");
- goto cleanup_candev;
- }
- netdev->netdev_ops = &panda_netdev_ops;
- netdev->flags |= IFF_ECHO; /* we support local echo */
-
- priv_inf = netdev_priv(netdev);
- priv_inf->netdev = netdev;
- priv_inf->priv_dev = priv_dev;
- priv_inf->interface_num = inf_num;
- priv_inf->mcu_can_ifnum = can_numbering[inf_num];
-
- init_usb_anchor(&priv_dev->rx_submitted);
- init_usb_anchor(&priv_inf->tx_submitted);
-
- /* Init CAN device */
- priv_inf->can.state = CAN_STATE_STOPPED;
- priv_inf->can.bittiming.bitrate = PANDA_BITRATE;
-
- SET_NETDEV_DEV(netdev, &intf->dev);
-
- err = register_candev(netdev);
- if (err) {
- netdev_err(netdev, "couldn't register PANDA CAN device: %d\n", err);
- free_candev(priv_inf->netdev);
- goto cleanup_candev;
- }
-
- priv_dev->interfaces[inf_num] = priv_inf;
- }
-
- err = panda_usb_start(priv_dev);
- if (err) {
- dev_err(&intf->dev, "Failed to initialize Comma.ai Panda CAN controller\n");
- goto cleanup_candev;
- }
-
- err = panda_set_output_enable(priv_inf, true);
- if (err) {
- dev_info(&intf->dev, "Failed to initialize send enable message to Panda.\n");
- goto cleanup_candev;
- }
-
- dev_info(&intf->dev, "Comma.ai Panda CAN controller connected\n");
-
- return 0;
-
- cleanup_candev:
- for(inf_num = 0; inf_num < PANDA_NUM_CAN_INTERFACES; inf_num++){
- priv_inf = priv_dev->interfaces[inf_num];
- if(priv_inf){
- unregister_candev(priv_inf->netdev);
- free_candev(priv_inf->netdev);
- }else
- break;
- }
-
- kfree(priv_dev);
-
- return err;
-}
-
-/* Called by the usb core when driver is unloaded or device is removed */
-static void panda_usb_disconnect(struct usb_interface *intf)
-{
- struct panda_dev_priv *priv_dev = usb_get_intfdata(intf);
- struct panda_inf_priv *priv_inf;
- int inf_num;
-
- usb_set_intfdata(intf, NULL);
-
- for(inf_num = 0; inf_num < PANDA_NUM_CAN_INTERFACES; inf_num++){
- priv_inf = priv_dev->interfaces[inf_num];
- if(priv_inf){
- netdev_info(priv_inf->netdev, "device disconnected\n");
- unregister_candev(priv_inf->netdev);
- free_candev(priv_inf->netdev);
- }else
- break;
- }
-
- panda_urb_unlink(priv_inf);
- kfree(priv_dev);
-}
-
-static struct usb_driver panda_usb_driver = {
- .name = PANDA_MODULE_NAME,
- .probe = panda_usb_probe,
- .disconnect = panda_usb_disconnect,
- .id_table = panda_usb_table,
-};
-
-module_usb_driver(panda_usb_driver);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Jessy Diamond Exum ");
-MODULE_DESCRIPTION("SocketCAN driver for Comma.ai's Panda Adapter.");
-MODULE_VERSION("0.1");
diff --git a/panda/drivers/linux/test/Makefile b/panda/drivers/linux/test/Makefile
deleted file mode 100644
index c73945e4c..000000000
--- a/panda/drivers/linux/test/Makefile
+++ /dev/null
@@ -1,2 +0,0 @@
-all:
- gcc main.c -o cantest -pthread -lpthread
diff --git a/panda/drivers/linux/test/main.c b/panda/drivers/linux/test/main.c
deleted file mode 100644
index 1f44efc76..000000000
--- a/panda/drivers/linux/test/main.c
+++ /dev/null
@@ -1,120 +0,0 @@
-#include
-#include
-#include
-#include
-#include
-
-#include
-#include
-#include
-#include
-
-#include
-#include
-
-const char *ifname = "can0";
-
-static unsigned char payload[] = {0xAA, 0xAA, 0xAA, 0xAA, 0x07, 0x00, 0x00, 0x00};
-int packet_len = 8;
-int dir = 0;
-
-void *write_thread( void *dat ){
- int nbytes;
- struct can_frame frame;
- int s = *((int*) dat);
-
- while(1){
- for(int i = 0; i < 1; i ++){
- if(packet_len % 2){
- frame.can_id = 0x8AA | CAN_EFF_FLAG;
- }else{
- frame.can_id = 0xAA;
- }
-
- frame.can_dlc = packet_len;
- memcpy(frame.data, payload, frame.can_dlc);
-
- nbytes = write(s, &frame, sizeof(struct can_frame));
-
- printf("Wrote %d bytes; addr: %lx; datlen: %d\n", nbytes, frame.can_id, frame.can_dlc);
-
- if(dir){
- packet_len++;
- if(packet_len >= 8)
- dir = 0;
- }else{
- packet_len--;
- if(packet_len <= 0)
- dir = 1;
- }
- }
- sleep(2);
- }
-}
-
-
-int main(void)
-{
- pthread_t sndthread;
- int err, s, nbytes;
- struct sockaddr_can addr;
- struct can_frame frame;
- struct ifreq ifr;
-
- if((s = socket(PF_CAN, SOCK_RAW, CAN_RAW)) < 0) {
- perror("Error while opening socket");
- return -1;
- }
-
- strcpy(ifr.ifr_name, ifname);
- ioctl(s, SIOCGIFINDEX, &ifr);
-
- addr.can_family = AF_CAN;
- addr.can_ifindex = ifr.ifr_ifindex;
-
- printf("%s at index %d\n", ifname, ifr.ifr_ifindex);
-
- if(bind(s, (struct sockaddr *)&addr, sizeof(addr)) < 0) {
- perror("Error in socket bind");
- return -2;
- }
-
- /////// Create Write Thread
-
- err = pthread_create( &sndthread, NULL, write_thread, (void*) &s);
- if(err){
- fprintf(stderr,"Error - pthread_create() return code: %d\n", err);
- exit(EXIT_FAILURE);
- }
-
- /////// Listen to socket
- while (1) {
- struct can_frame framein;
-
- // Read in a CAN frame
- int numBytes = read(s, &framein, CANFD_MTU);
- switch (numBytes) {
- case CAN_MTU:
- if(framein.can_id & 0x80000000)
- printf("Received %u byte payload; canid 0x%lx (EXT)\n",
- framein.can_dlc, framein.can_id & 0x7FFFFFFF);
- else
- printf("Received %u byte payload; canid 0x%lx\n", framein.can_dlc, framein.can_id);
- break;
- case CANFD_MTU:
- // TODO: Should make an example for CAN FD
- break;
- case -1:
- // Check the signal value on interrupt
- //if (EINTR == errno)
- // continue;
-
- // Delay before continuing
- sleep(1);
- default:
- continue;
- }
- }
-
- return 0;
-}
diff --git a/panda/drivers/linux/test/run.sh b/panda/drivers/linux/test/run.sh
deleted file mode 100755
index 5301719b4..000000000
--- a/panda/drivers/linux/test/run.sh
+++ /dev/null
@@ -1,4 +0,0 @@
-#!/usr/bin/env bash
-sudo ifconfig can0 up
-make
-./cantest
diff --git a/panda/drivers/windows/.gitignore b/panda/drivers/windows/.gitignore
deleted file mode 100644
index dbe7ad5a9..000000000
--- a/panda/drivers/windows/.gitignore
+++ /dev/null
@@ -1,306 +0,0 @@
-## Ignore Visual Studio temporary files, build results, and
-## files generated by popular Visual Studio add-ons.
-##
-## Get latest from https://github.com/github/gitignore/blob/master/VisualStudio.gitignore
-
-# User-specific files
-*.suo
-*.user
-*.userosscache
-*.sln.docstates
-
-# User-specific files (MonoDevelop/Xamarin Studio)
-*.userprefs
-
-# Build results
-Debug_x86/
-Debug_x64/
-Release_x86/
-Release_x64/
-[Dd]ebug/
-[Dd]ebugPublic/
-[Rr]elease/
-[Rr]eleases/
-x64/
-x86/
-bld/
-[Bb]in/
-[Oo]bj/
-[Ll]og/
-
-# Visual Studio 2015 cache/options directory
-.vs/
-# Uncomment if you have tasks that create the project's static files in wwwroot
-#wwwroot/
-
-# MSTest test Results
-[Tt]est[Rr]esult*/
-[Bb]uild[Ll]og.*
-
-# NUNIT
-*.VisualState.xml
-TestResult.xml
-
-# Build Results of an ATL Project
-[Dd]ebugPS/
-[Rr]eleasePS/
-dlldata.c
-
-# Benchmark Results
-BenchmarkDotNet.Artifacts/
-
-# .NET Core
-project.lock.json
-project.fragment.lock.json
-artifacts/
-**/Properties/launchSettings.json
-
-*_i.c
-*_p.c
-*_i.h
-*.ilk
-*.meta
-*.obj
-*.pch
-*.pdb
-*.pgc
-*.pgd
-*.rsp
-*.sbr
-*.tlb
-*.tli
-*.tlh
-*.tmp
-*.tmp_proj
-*.log
-*.vspscc
-*.vssscc
-.builds
-*.pidb
-*.svclog
-*.scc
-
-# Chutzpah Test files
-_Chutzpah*
-
-# Visual C++ cache files
-ipch/
-*.aps
-*.ncb
-*.opendb
-*.opensdf
-*.sdf
-*.cachefile
-*.VC.db
-*.VC.VC.opendb
-
-# Visual Studio profiler
-*.psess
-*.vsp
-*.vspx
-*.sap
-
-# TFS 2012 Local Workspace
-$tf/
-
-# Guidance Automation Toolkit
-*.gpState
-
-# ReSharper is a .NET coding add-in
-_ReSharper*/
-*.[Rr]e[Ss]harper
-*.DotSettings.user
-
-# JustCode is a .NET coding add-in
-.JustCode
-
-# TeamCity is a build add-in
-_TeamCity*
-
-# DotCover is a Code Coverage Tool
-*.dotCover
-
-# AxoCover is a Code Coverage Tool
-.axoCover/*
-!.axoCover/settings.json
-
-# Visual Studio code coverage results
-*.coverage
-*.coveragexml
-
-# NCrunch
-_NCrunch_*
-.*crunch*.local.xml
-nCrunchTemp_*
-
-# MightyMoose
-*.mm.*
-AutoTest.Net/
-
-# Web workbench (sass)
-.sass-cache/
-
-# Installshield output folder
-[Ee]xpress/
-
-# DocProject is a documentation generator add-in
-DocProject/buildhelp/
-DocProject/Help/*.HxT
-DocProject/Help/*.HxC
-DocProject/Help/*.hhc
-DocProject/Help/*.hhk
-DocProject/Help/*.hhp
-DocProject/Help/Html2
-DocProject/Help/html
-
-# Click-Once directory
-publish/
-
-# Publish Web Output
-*.[Pp]ublish.xml
-*.azurePubxml
-# Note: Comment the next line if you want to checkin your web deploy settings,
-# but database connection strings (with potential passwords) will be unencrypted
-*.pubxml
-*.publishproj
-
-# Microsoft Azure Web App publish settings. Comment the next line if you want to
-# checkin your Azure Web App publish settings, but sensitive information contained
-# in these scripts will be unencrypted
-PublishScripts/
-
-# NuGet Packages
-*.nupkg
-# The packages folder can be ignored because of Package Restore
-**/packages/*
-# except build/, which is used as an MSBuild target.
-!**/packages/build/
-# Uncomment if necessary however generally it will be regenerated when needed
-#!**/packages/repositories.config
-# NuGet v3's project.json files produces more ignorable files
-*.nuget.props
-*.nuget.targets
-
-# Microsoft Azure Build Output
-csx/
-*.build.csdef
-
-# Microsoft Azure Emulator
-ecf/
-rcf/
-
-# Windows Store app package directories and files
-AppPackages/
-BundleArtifacts/
-Package.StoreAssociation.xml
-_pkginfo.txt
-*.appx
-
-# Visual Studio cache files
-# files ending in .cache can be ignored
-*.[Cc]ache
-# but keep track of directories ending in .cache
-!*.[Cc]ache/
-
-# Others
-ClientBin/
-~$*
-*~
-*.dbmdl
-*.dbproj.schemaview
-*.jfm
-*.pfx
-*.publishsettings
-orleans.codegen.cs
-
-# Since there are multiple workflows, uncomment next line to ignore bower_components
-# (https://github.com/github/gitignore/pull/1529#issuecomment-104372622)
-#bower_components/
-
-# RIA/Silverlight projects
-Generated_Code/
-
-# Backup & report files from converting an old project file
-# to a newer Visual Studio version. Backup files are not needed,
-# because we have git ;-)
-_UpgradeReport_Files/
-Backup*/
-UpgradeLog*.XML
-UpgradeLog*.htm
-
-# SQL Server files
-*.mdf
-*.ldf
-*.ndf
-
-# Business Intelligence projects
-*.rdl.data
-*.bim.layout
-*.bim_*.settings
-
-# Microsoft Fakes
-FakesAssemblies/
-
-# GhostDoc plugin setting file
-*.GhostDoc.xml
-
-# Node.js Tools for Visual Studio
-.ntvs_analysis.dat
-node_modules/
-
-# Typescript v1 declaration files
-typings/
-
-# Visual Studio 6 build log
-*.plg
-
-# Visual Studio 6 workspace options file
-*.opt
-
-# Visual Studio 6 auto-generated workspace file (contains which files were open etc.)
-*.vbw
-
-# Visual Studio LightSwitch build output
-**/*.HTMLClient/GeneratedArtifacts
-**/*.DesktopClient/GeneratedArtifacts
-**/*.DesktopClient/ModelManifest.xml
-**/*.Server/GeneratedArtifacts
-**/*.Server/ModelManifest.xml
-_Pvt_Extensions
-
-# Paket dependency manager
-.paket/paket.exe
-paket-files/
-
-# FAKE - F# Make
-.fake/
-
-# JetBrains Rider
-.idea/
-*.sln.iml
-
-# CodeRush
-.cr/
-
-# Python Tools for Visual Studio (PTVS)
-__pycache__/
-*.pyc
-
-# Cake - Uncomment if you are using it
-# tools/**
-# !tools/packages.config
-
-# Tabs Studio
-*.tss
-
-# Telerik's JustMock configuration file
-*.jmconfig
-
-# BizTalk build output
-*.btp.cs
-*.btm.cs
-*.odx.cs
-*.xsd.cs
-
-# installer
-*.exe
diff --git a/panda/drivers/windows/ECUsim CLI/ECUsim CLI.cpp b/panda/drivers/windows/ECUsim CLI/ECUsim CLI.cpp
deleted file mode 100644
index 6c8a469ac..000000000
--- a/panda/drivers/windows/ECUsim CLI/ECUsim CLI.cpp
+++ /dev/null
@@ -1,38 +0,0 @@
-// ECUsim CLI.cpp : Defines the entry point for the console application.
-//
-
-#include "stdafx.h"
-#include "ECUsim DLL\ECUsim.h"
-
-std::unique_ptr sim;
-
-BOOL CtrlHandler(DWORD fdwCtrlType)
-{
- if (fdwCtrlType != CTRL_C_EVENT) return FALSE;
-
- sim->stop();
- sim->join();
-
- return(TRUE);
-}
-
-int main(int argc, // Number of strings in array argv
- char *argv[], // Array of command-line argument strings
- char *envp[]) // Array of environment variable strings
-{
-
- int count;
-
- // Display each command-line argument.
- std::cout << "\nCommand-line arguments:\n";
- for (count = 0; count < argc; count++)
- std::cout << " argv[" << count << "] " << argv[count] << "\n";
-
- SetConsoleCtrlHandler((PHANDLER_ROUTINE)CtrlHandler, TRUE);
-
- sim.reset(new ECUsim("", 500000));
- sim->join();
-
- return 0;
-}
-
diff --git a/panda/drivers/windows/ECUsim CLI/ECUsim CLI.vcxproj b/panda/drivers/windows/ECUsim CLI/ECUsim CLI.vcxproj
deleted file mode 100644
index 4b9de8c44..000000000
--- a/panda/drivers/windows/ECUsim CLI/ECUsim CLI.vcxproj
+++ /dev/null
@@ -1,178 +0,0 @@
-
-
-
-
- Debug
- Win32
-
-
- Release
- Win32
-
-
- Debug
- x64
-
-
- Release
- x64
-
-
-
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}
- Win32Proj
- ECUsimCLI
- 10.0.16299.0
-
-
- Application
- true
- v141
- Unicode
-
-
- Application
- false
- v141
- true
- Unicode
-
-
- Application
- true
- v141
- Unicode
-
-
- Application
- false
- v141
- true
- Unicode
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- true
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- true
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- false
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- false
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
-
- Use
- Level3
- Disabled
- WIN32;_DEBUG;_CONSOLE;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Console
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)ecusim.lib
-
-
-
-
- Use
- Level3
- Disabled
- _DEBUG;_CONSOLE;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Console
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)ecusim.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- WIN32;NDEBUG;_CONSOLE;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Console
- true
- true
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)ecusim.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- NDEBUG;_CONSOLE;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Console
- true
- true
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)ecusim.lib
-
-
-
-
-
-
- Create
- Create
- Create
- Create
-
-
-
-
- {96e0e646-ee76-444d-9a77-a0cd7f781deb}
-
-
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/ECUsim CLI/ECUsim CLI.vcxproj.filters b/panda/drivers/windows/ECUsim CLI/ECUsim CLI.vcxproj.filters
deleted file mode 100644
index ea223e30b..000000000
--- a/panda/drivers/windows/ECUsim CLI/ECUsim CLI.vcxproj.filters
+++ /dev/null
@@ -1,36 +0,0 @@
-
-
-
-
- {4FC737F1-C7A5-4376-A066-2A32D752A2FF}
- cpp;c;cc;cxx;def;odl;idl;hpj;bat;asm;asmx
-
-
- {93995380-89BD-4b04-88EB-625FBE52EBFB}
- h;hh;hpp;hxx;hm;inl;inc;xsd
-
-
- {67DA6AB6-F800-4c08-8B7A-83BB121AAD01}
- rc;ico;cur;bmp;dlg;rc2;rct;bin;rgs;gif;jpg;jpeg;jpe;resx;tiff;tif;png;wav;mfcribbon-ms
-
-
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
-
-
- Source Files
-
-
- Source Files
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/ECUsim CLI/stdafx.cpp b/panda/drivers/windows/ECUsim CLI/stdafx.cpp
deleted file mode 100644
index d4a23c3cf..000000000
--- a/panda/drivers/windows/ECUsim CLI/stdafx.cpp
+++ /dev/null
@@ -1,8 +0,0 @@
-// stdafx.cpp : source file that includes just the standard includes
-// ECUsim CLI.pch will be the pre-compiled header
-// stdafx.obj will contain the pre-compiled type information
-
-#include "stdafx.h"
-
-// TODO: reference any additional headers you need in STDAFX.H
-// and not in this file
diff --git a/panda/drivers/windows/ECUsim CLI/stdafx.h b/panda/drivers/windows/ECUsim CLI/stdafx.h
deleted file mode 100644
index b005a839d..000000000
--- a/panda/drivers/windows/ECUsim CLI/stdafx.h
+++ /dev/null
@@ -1,15 +0,0 @@
-// stdafx.h : include file for standard system include files,
-// or project specific include files that are used frequently, but
-// are changed infrequently
-//
-
-#pragma once
-
-#include "targetver.h"
-
-#include
-#include
-
-
-
-// TODO: reference additional headers your program requires here
diff --git a/panda/drivers/windows/ECUsim CLI/targetver.h b/panda/drivers/windows/ECUsim CLI/targetver.h
deleted file mode 100644
index 87c0086de..000000000
--- a/panda/drivers/windows/ECUsim CLI/targetver.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#pragma once
-
-// Including SDKDDKVer.h defines the highest available Windows platform.
-
-// If you wish to build your application for a previous Windows platform, include WinSDKVer.h and
-// set the _WIN32_WINNT macro to the platform you wish to support before including SDKDDKVer.h.
-
-#include
diff --git a/panda/drivers/windows/ECUsim DLL/ECUsim DLL.vcxproj b/panda/drivers/windows/ECUsim DLL/ECUsim DLL.vcxproj
deleted file mode 100644
index 93d75c14b..000000000
--- a/panda/drivers/windows/ECUsim DLL/ECUsim DLL.vcxproj
+++ /dev/null
@@ -1,197 +0,0 @@
-
-
-
-
- Debug
- Win32
-
-
- Release
- Win32
-
-
- Debug
- x64
-
-
- Release
- x64
-
-
-
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}
- Win32Proj
- ECUsimDLL
- 10.0.16299.0
-
-
- DynamicLibrary
- true
- v141
- Unicode
-
-
- DynamicLibrary
- false
- v141
- true
- Unicode
-
-
- DynamicLibrary
- true
- v141
- Unicode
-
-
- DynamicLibrary
- false
- v141
- true
- Unicode
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- true
- ecusim
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- true
- ecusim
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- false
- ecusim
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- false
- ecusim
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
-
- Use
- Level3
- Disabled
- WIN32;_DEBUG;_WINDOWS;_USRDLL;ECUSIMDLL_EXPORTS;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Windows
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)panda.lib
-
-
-
-
- Use
- Level3
- Disabled
- _DEBUG;_WINDOWS;_USRDLL;ECUSIMDLL_EXPORTS;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Windows
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)panda.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- WIN32;NDEBUG;_WINDOWS;_USRDLL;ECUSIMDLL_EXPORTS;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Windows
- true
- true
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)panda.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- NDEBUG;_WINDOWS;_USRDLL;ECUSIMDLL_EXPORTS;%(PreprocessorDefinitions)
- true
- %(AdditionalIncludeDirectories);$(SolutionDir)
-
- Windows
- true
- true
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)panda.lib
-
-
-
-
-
-
- false
-
-
- false
-
-
- false
-
-
- false
-
-
-
-
- Create
- Create
- Create
- Create
-
-
-
-
- {5528aefb-638d-49af-b9d4-965154e7d531}
-
-
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/ECUsim DLL/ECUsim DLL.vcxproj.filters b/panda/drivers/windows/ECUsim DLL/ECUsim DLL.vcxproj.filters
deleted file mode 100644
index 299d65445..000000000
--- a/panda/drivers/windows/ECUsim DLL/ECUsim DLL.vcxproj.filters
+++ /dev/null
@@ -1,42 +0,0 @@
-
-
-
-
- {4FC737F1-C7A5-4376-A066-2A32D752A2FF}
- cpp;c;cc;cxx;def;odl;idl;hpj;bat;asm;asmx
-
-
- {93995380-89BD-4b04-88EB-625FBE52EBFB}
- h;hh;hpp;hxx;hm;inl;inc;xsd
-
-
- {67DA6AB6-F800-4c08-8B7A-83BB121AAD01}
- rc;ico;cur;bmp;dlg;rc2;rct;bin;rgs;gif;jpg;jpeg;jpe;resx;tiff;tif;png;wav;mfcribbon-ms
-
-
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
-
-
- Source Files
-
-
- Source Files
-
-
- Source Files
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/ECUsim DLL/ECUsim.cpp b/panda/drivers/windows/ECUsim DLL/ECUsim.cpp
deleted file mode 100644
index 19f2bf360..000000000
--- a/panda/drivers/windows/ECUsim DLL/ECUsim.cpp
+++ /dev/null
@@ -1,261 +0,0 @@
-#include "stdafx.h"
-#include "ECUsim.h"
-
-ECUsim::ECUsim(std::string sn, unsigned long can_baud, bool ext_addr) :
- doloop(TRUE), verbose(TRUE), can11b_enabled(TRUE), can29b_enabled(TRUE), ext_addr(ext_addr){
- this->panda = panda::Panda::openPanda(sn);
- this->panda->set_can_speed_cbps(panda::PANDA_CAN1, can_baud / 100); //Don't pass in baud where baud%100 != 0
- this->panda->set_safety_mode(panda::SAFETY_ALLOUTPUT);
- this->panda->set_can_loopback(FALSE);
- this->panda->can_clear(panda::PANDA_CAN_RX);
-
- DWORD threadid;
- this->thread_can = CreateThread(NULL, 0, _canthreadBootstrap, (LPVOID)this, 0, &threadid);
-}
-
-ECUsim::~ECUsim() {
- this->stop();
- this->join();
-}
-
-void ECUsim::stop() {
- this->doloop = FALSE;
-}
-
-void ECUsim::join() {
- WaitForSingleObject(this->thread_can, INFINITE);
-}
-
-DWORD WINAPI ECUsim::_canthreadBootstrap(LPVOID This) {
- return ((ECUsim*)This)->can_recv_thread_function();
-}
-
-DWORD ECUsim::can_recv_thread_function() {
- while (this->doloop) {
- auto msgs = this->panda->can_recv();
- for (auto& msg : msgs) {
- if (msg.is_receipt) continue;
- if (msg.bus == 0 && !msg.is_receipt /*&& msg.len == 8*/ && msg.dat[0] >= 2) {
- if (this->verbose) {
- printf("Processing message (bus: %d; addr: %X; 29b: %d):\n ", msg.bus, msg.addr, msg.addr_29b);
- for (int i = 0; i < msg.len; i++) printf("%02X ", msg.dat[i]);
- printf("\n");
- }
- this->_CAN_process_msg(msg);
- } else {
- if (this->verbose) {
- printf("Rejecting message (bus: %d; addr: %X; 29b: %d):\n ", msg.bus, msg.addr, msg.addr_29b);
- for (int i = 0; i < msg.len; i++) printf("%02X ", msg.dat[i]);
- printf("\n");
- }
- }
- }
- }
-
- return 0;
-}
-
-BOOL ECUsim::_can_addr_matches(panda::PANDA_CAN_MSG& msg) {
- if (this->can11b_enabled && !msg.addr_29b && (msg.addr == 0x7DF || (msg.addr & 0x7F8) == 0x7E0)) {
- if (!this->ext_addr) {
- return TRUE;
- } else {
- return msg.len >= 1 && msg.dat[0] == 0x13;//13 is an arbitrary address picked to test ext addresses
- }
- }
- if (this->can29b_enabled && msg.addr_29b && ((msg.addr & 0x1FFF00FF) == 0x18DB00F1 || (msg.addr & 0x1FFF00FF) == 0x18da00f1)) {
- if (!this->ext_addr) {
- return TRUE;
- } else {
- return msg.len >= 1 && msg.dat[0] == 0x13;//13 is an arbitrary address picked to test ext addresses
- }
- }
- return FALSE;
-}
-
-void ECUsim::_CAN_process_msg(panda::PANDA_CAN_MSG& msg) {
- std::string outmsg;
- uint32_t outaddr;
- uint8_t formatted_msg_buff[8];
- bool doreply = FALSE;
-
- if (this->_can_addr_matches(msg)) {// && msg.len == 8) {
- uint8_t *dat = (this->ext_addr) ? &msg.dat[1] : &msg.dat[0];
- if ((dat[0] & 0xF0) == 0x10) {
- printf("Got a multiframe write request\n");
- outaddr = (msg.addr_29b) ? 0x18DAF1EF : 0x7E8;
- this->panda->can_send(outaddr, msg.addr_29b, (const uint8_t*)"\x30\x00\x00", 3, panda::PANDA_CAN1);
- return;
- }
-
- /////////// Check if Flow Control Msg
- if ((dat[0] & 0xF0) == 0x30 && msg.len >= 3 && this->can_multipart_data.size() > 0) {
- if (this->verbose) printf("More data requested\n");
- uint8_t block_size = dat[1], sep_time_min = dat[2];
- outaddr = (msg.addr == 0x7DF || msg.addr == 0x7E0) ? 0x7E8 : 0x18DAF1EF; //ext addr 5th byte is just always 0x13 for simplicity
-
- unsigned int msgnum = 1;
- while (this->can_multipart_data.size()) {
- unsigned int datalen = this->ext_addr ?
- min(6, this->can_multipart_data.size()): //EXT ADDR VALUE
- min(7, this->can_multipart_data.size()); //NORMAL ADDR VALUE
-
- unsigned int idx = 0;
- if (this->ext_addr)
- formatted_msg_buff[idx++] = 0x13; //EXT ADDR
- formatted_msg_buff[idx++] = 0x20 | msgnum;
- for (int i = 0; i < datalen; i++) {
- formatted_msg_buff[i + idx] = this->can_multipart_data.front();
- this->can_multipart_data.pop();
- }
- for (int i = datalen + idx; i < sizeof(formatted_msg_buff); i++)
- formatted_msg_buff[i] = 0;
-
- if (this->verbose) {
- printf("Multipart reply to %X.\n ", outaddr);
- for (int i = 0; i < datalen + idx; i++) printf("%02X ", formatted_msg_buff[i]);
- printf("\n");
- }
-
- this->panda->can_send(outaddr, msg.addr_29b, formatted_msg_buff, datalen + idx, panda::PANDA_CAN1);
- msgnum = (msgnum + 1) % 0x10;
- Sleep(10);
- }
- return;
- }
-
- /////////// Normal message in
- outmsg = this->process_obd_msg(dat[1], dat[2], doreply);
- if (doreply) {
- outaddr = (msg.addr_29b) ? 0x18DAF1EF : 0x7E8;
-
- if (outmsg.size() <= (this->ext_addr ? 4 : 5)) {
- unsigned int idx = 0;
- if(this->ext_addr)
- formatted_msg_buff[idx++] = 0x13; //EXT ADDR
- formatted_msg_buff[idx++] = outmsg.size() + 2;
- formatted_msg_buff[idx++] = 0x40 | dat[1];
- formatted_msg_buff[idx++] = dat[2]; //PID
- memcpy_s(&formatted_msg_buff[idx], sizeof(formatted_msg_buff) - idx, outmsg.c_str(), outmsg.size());
- for (int i = idx + outmsg.size(); i < 8; i++)
- formatted_msg_buff[i] = 0;
-
- if (this->verbose) {
- printf("Replying to %X.\n ", outaddr);
- for (int i = 0; i < 8; i++) printf("%02X ", formatted_msg_buff[i]);
- printf("\n");
- }
-
- this->panda->can_send(outaddr, msg.addr_29b, formatted_msg_buff, 8, panda::PANDA_CAN1); //outmsg.size() + 3
- } else {
- uint8_t first_msg_len = this->ext_addr ?
- min(2, outmsg.size() % 7) : //EXT ADDR VALUES
- min(3, outmsg.size() % 7); //NORMAL ADDR VALUES
- uint8_t payload_len = outmsg.size() + 3;
-
- unsigned int idx = 0;
- if (this->ext_addr)
- formatted_msg_buff[idx++] = 0x13; //EXT ADDR
- formatted_msg_buff[idx++] = 0x10 | ((payload_len >> 8) & 0xF);
- formatted_msg_buff[idx++] = payload_len & 0xFF;
- formatted_msg_buff[idx++] = 0x40 | dat[1];
- formatted_msg_buff[idx++] = dat[2]; //PID
- formatted_msg_buff[idx++] = 1;
- memcpy_s(&formatted_msg_buff[idx], sizeof(formatted_msg_buff) - idx, outmsg.c_str(), first_msg_len);
-
- if (this->verbose) {
- printf("Replying FIRST FRAME to %X.\n ", outaddr);
- for (int i = 0; i < 8; i++) printf("%02X ", formatted_msg_buff[i]);
- printf("\n");
- }
-
- this->panda->can_send(outaddr, msg.addr_29b, formatted_msg_buff, 8, panda::PANDA_CAN1);
- for (int i = first_msg_len; i < outmsg.size(); i++)
- this->can_multipart_data.push(outmsg[i]);
- }
- }
- }
-}
-
-std::string ECUsim::process_obd_msg(UCHAR mode, UCHAR pid, bool& return_data) {
- std::string tmp;
- return_data = TRUE;
-
- switch (mode) {
- case 0x01: // Mode : Show current data
- switch (pid) {
- case 0x00: //List supported things
- return "\xff\xff\xff\xfe"; //b"\xBE\x1F\xB8\x10" #Bitfield, random features
- case 0x01: // Monitor Status since DTC cleared
- return std::string("\x00\x00\x00\x00", 4); //Bitfield, random features
- case 0x04: // Calculated engine load
- return "\x2f";
- case 0x05: // Engine coolant temperature
- return "\x3c";
- case 0x0B: // Intake manifold absolute pressure
- return "\x90";
- case 0x0C: // Engine RPM
- return "\x1A\xF8";
- case 0x0D: // Vehicle Speed
- return "\x53";
- case 0x10: // MAF air flow rate
- return "\x01\xA0";
- case 0x11: // Throttle Position
- return "\x90";
- case 0x33: // Absolute Barometric Pressure
- return "\x90";
- default:
- return_data = FALSE;
- return "";
- }
- case 0x09: // Mode : Request vehicle information
- switch (pid) {
- case 0x02: // Show VIN
- return "1D4GP00R55B123456";
- case 0xFC: // test long multi message.Ligned up for LIN responses
- for (int i = 0; i < 80; i++) {
- tmp += "\xAA\xAA";
- }
- return tmp;//">BBH", 0xAA, 0xAA, num + 1)
- case 0xFD: // test long multi message
- for (int i = 0; i < 80; i++) {
- tmp += "\xAA\xAA\xAA";
- tmp.push_back(i >> 24);
- tmp.push_back((i >> 16) & 0xFF);
- tmp.push_back((i >> 8) & 0xFF);
- tmp.push_back(i & 0xFF);
- }
- return "\xAA\xAA\xAA" + tmp;
- case 0xFE: // test very long multi message
- tmp = "\xAA\xAA\xAA";
- for (int i = 0; i < 584; i++) {
- tmp += "\xAA\xAA\xAA";
- tmp.push_back(i >> 24);
- tmp.push_back((i >> 16) & 0xFF);
- tmp.push_back((i >> 8) & 0xFF);
- tmp.push_back(i & 0xFF);
- }
- return tmp + "\xAA";
- case 0xFF:
- for (int i = 0; i < 584; i++) {
- tmp += "\xAA\xAA\xAA\xAA\xAA";
- tmp.push_back(((i + 1) >> 8) & 0xFF);
- tmp.push_back((i + 1) & 0xFF);
- }
- return std::string("\xAA\x00\x00", 3) + tmp;
- default:
- return_data = FALSE;
- return "";
- }
- case 0x3E:
- if (pid == 0) {
- return_data = TRUE;
- return "";
- }
- return_data = FALSE;
- return "";
- default:
- return_data = FALSE;
- return "";
- }
-}
diff --git a/panda/drivers/windows/ECUsim DLL/ECUsim.h b/panda/drivers/windows/ECUsim DLL/ECUsim.h
deleted file mode 100644
index 2f5fe0f7a..000000000
--- a/panda/drivers/windows/ECUsim DLL/ECUsim.h
+++ /dev/null
@@ -1,50 +0,0 @@
-#pragma once
-
-#include
-#include "panda_shared/panda.h"
-#include
-
-// The following ifdef block is the standard way of creating macros which make exporting
-// from a DLL simpler. All files within this DLL are compiled with the ECUSIMDLL_EXPORTS
-// symbol defined on the command line. This symbol should not be defined on any project
-// that uses this DLL. This way any other project whose source files include this file see
-// ECUSIMDLL_API functions as being imported from a DLL, whereas this DLL sees symbols
-// defined with this macro as being exported.
-#ifdef ECUSIMDLL_EXPORTS
-#define ECUSIMDLL_API __declspec(dllexport)
-#else
-#define ECUSIMDLL_API __declspec(dllimport)
-#endif
-
-// This class is exported from the ECUsim DLL.dll
-class ECUSIMDLL_API ECUsim {
-public:
- ECUsim(std::string sn, unsigned long can_baud, bool ext_addr = FALSE);
- ECUsim(panda::Panda && p, unsigned long can_baud, bool ext_addr = FALSE);
- ~ECUsim();
-
- void stop();
- void join();
-
- // Flag determines if verbose output is enabled
- volatile bool verbose;
- BOOL ext_addr;
-private:
- std::unique_ptr panda;
-
- static DWORD WINAPI _canthreadBootstrap(LPVOID This);
- DWORD can_recv_thread_function();
-
- BOOL _can_addr_matches(panda::PANDA_CAN_MSG & msg);
-
- void _CAN_process_msg(panda::PANDA_CAN_MSG & msg);
-
- std::string process_obd_msg(UCHAR mode, UCHAR pid, bool& return_data);
-
- HANDLE thread_can;
- volatile bool doloop;
- std::queue can_multipart_data;
-
- BOOL can11b_enabled;
- BOOL can29b_enabled;
-};
diff --git a/panda/drivers/windows/ECUsim DLL/dllmain.cpp b/panda/drivers/windows/ECUsim DLL/dllmain.cpp
deleted file mode 100644
index 69b58914b..000000000
--- a/panda/drivers/windows/ECUsim DLL/dllmain.cpp
+++ /dev/null
@@ -1,19 +0,0 @@
-// dllmain.cpp : Defines the entry point for the DLL application.
-#include "stdafx.h"
-
-BOOL APIENTRY DllMain( HMODULE hModule,
- DWORD ul_reason_for_call,
- LPVOID lpReserved
- )
-{
- switch (ul_reason_for_call)
- {
- case DLL_PROCESS_ATTACH:
- case DLL_THREAD_ATTACH:
- case DLL_THREAD_DETACH:
- case DLL_PROCESS_DETACH:
- break;
- }
- return TRUE;
-}
-
diff --git a/panda/drivers/windows/ECUsim DLL/stdafx.cpp b/panda/drivers/windows/ECUsim DLL/stdafx.cpp
deleted file mode 100644
index b4056ecd0..000000000
--- a/panda/drivers/windows/ECUsim DLL/stdafx.cpp
+++ /dev/null
@@ -1,8 +0,0 @@
-// stdafx.cpp : source file that includes just the standard includes
-// ECUsim DLL.pch will be the pre-compiled header
-// stdafx.obj will contain the pre-compiled type information
-
-#include "stdafx.h"
-
-// TODO: reference any additional headers you need in STDAFX.H
-// and not in this file
diff --git a/panda/drivers/windows/ECUsim DLL/stdafx.h b/panda/drivers/windows/ECUsim DLL/stdafx.h
deleted file mode 100644
index f3a07375c..000000000
--- a/panda/drivers/windows/ECUsim DLL/stdafx.h
+++ /dev/null
@@ -1,16 +0,0 @@
-// stdafx.h : include file for standard system include files,
-// or project specific include files that are used frequently, but
-// are changed infrequently
-//
-
-#pragma once
-
-#include "targetver.h"
-
-#define WIN32_LEAN_AND_MEAN // Exclude rarely-used stuff from Windows headers
-// Windows Header Files:
-#include
-
-
-
-// TODO: reference additional headers your program requires here
diff --git a/panda/drivers/windows/ECUsim DLL/targetver.h b/panda/drivers/windows/ECUsim DLL/targetver.h
deleted file mode 100644
index 87c0086de..000000000
--- a/panda/drivers/windows/ECUsim DLL/targetver.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#pragma once
-
-// Including SDKDDKVer.h defines the highest available Windows platform.
-
-// If you wish to build your application for a previous Windows platform, include WinSDKVer.h and
-// set the _WIN32_WINNT macro to the platform you wish to support before including SDKDDKVer.h.
-
-#include
diff --git a/panda/drivers/windows/README.md b/panda/drivers/windows/README.md
deleted file mode 100644
index 06c7a5110..000000000
--- a/panda/drivers/windows/README.md
+++ /dev/null
@@ -1,144 +0,0 @@
-```
- ;" ^; ;' ",
-______/\\\\\\\\\\\____/\\\\\\\\\_______/\\\\\\\\\\\\\\\______/\\\\\\\\\\_____________/\\\____ ; s$$$$$$$s ;
- _____\/////\\\///___/\\\///////\\\____\/\\\///////////_____/\\\///////\\\__________/\\\\\____ , ss$$$$$$$$$$s ,'
- _________\/\\\_____\///______\//\\\___\/\\\_______________\///______/\\\_________/\\\/\\\____ ;s$$$$$$$$$$$$$$$
- _________\/\\\_______________/\\\/____\/\\\\\\\\\\\\_____________/\\\//________/\\\/\/\\\____ $$$$$$$$$$$$$$$$$$
- _________\/\\\____________/\\\//______\////////////\\\__________\////\\\_____/\\\/__\/\\\____ $$$$P""Y$$$Y""W$$$$$
- _________\/\\\_________/\\\//____________________\//\\\____________\//\\\__/\\\\\\\\\\\\\\\\_ $$$$ p"$$$"q $$$$$
- __/\\\___\/\\\_______/\\\/____________/\\\________\/\\\___/\\\______/\\\__\///////////\\\//__ $$$$ .$$$$$. $$$$
- _\//\\\\\\\\\_______/\\\\\\\\\\\\\\\_\//\\\\\\\\\\\\\/___\///\\\\\\\\\/_____________\/\\\____ _ $$$$$$$$$$$$$$$$
- __\/////////_______\///////////////___\/////////////_______\/////////_______________\///_____| | "Y$$$"*"$$$Y"
- _ __ __ _ _ __ __| | __ _"$b.$$"
- | '_ \ / _` | '_ \ / _` |/ _` |
- | |_) | (_| | | | | (_| | (_| |
- | .__/ \__,_|_| |_|\__,_|\__,_|
- | | A comma.ai product.
- |_| (Code by Jessy Diamond Exum)
-```
-
-
-# Installing J2534 driver:
-
-[Download](https://github.com/commaai/panda/files/1742802/panda.J2534.driver.install.zip)
-
-Depending on what version of windows you are on, you may need to separately install the WinUSB driver (see next section).
-
-# Installing WinUSB driver:
-
-Installation automatically happens for Windows 8 and Windows 10 because the panda
-firmware contains the USB descriptors necessary to auto-install the WinUSB driver.
-
-Windows 7 will not auto-install the WinUSB driver. You can use Zadig to install
-the WinUSB driver. This software is not tested on anything before 7.
-
-More details here:
-[WinUSB (Winusb.sys) Installation](https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/winusb-installation)
-[WCID Devices](https://github.com/pbatard/libwdi/wiki/WCID-Devices)
-[Zadig for installing libusb compatible driver](https://github.com/pbatard/libwdi/wiki/Zadig)
-
-# Using J2534:
-
-After installing the J2534 drivers for the panda, you can do... nothing.
-You first need to get a J2534 client that can load the drivers and talk to
-the panda for you.
-
-A simple tool for testing J2534 drivers is DrewTech's 'J2534-1 Bus Analysis
-Tool' available in the 'Other Support Applications' section of their
-[Download Page](http://www.drewtech.com/downloads/).
-
-# What is J2534?
-
-J2534 is an API that tries to provide a consistent way to send/receive
-messages over the many different protocols supported by the OBD II
-port. The place this is perhaps most obvious, is sending data over
-different protocols (each using unique packetizing methods) using the
-same data format.
-
-For each PassThru Device that should be used with J2534 (in this case,
-the panda), a 'driver' has to be written that can be loaded by a
-client application wanting to send/receive data.
-
-A lot of J2534 has good ideas behind it, but the standard has some odd choices:
-
-* Platform Locked: Requires using the Windows Registry to find installed J2534 libraries/drivers. Drivers have to be DLLs.
-* Architecture Locked: So far there is only support for x86.
-* No device autodetect, and poor support for selecting from multiple devices.
-* Constant vague language about important behavior (small differences between vendors).
-* Most common differences become standard in later revisions.
-
-# Why use J2534 with the panda?
-
-J2534 is the only interface supported by most professional grade
-vehicle diagnostics systems (such as HDS). These tools are useful for
-diagnosing vehicles, as well as reverse engineering some lesser known
-features.
-
-# What parts are supported with panda?
-
-- [ ] **J1850VPW** *(Outdated, and not physically supported by the panda)*
-- [ ] **J1850PWM** *(Outdated, and not physically supported by the panda)*
-- [X] **CAN**
-- [X] **ISO15765**
-- [ ] **ISO9141** *(This protocol could be implemented if 5 BAUD init support is added to the panda.)*
-- [ ] **ISO14230/KWP2000** *(Could be supported with FAST init, 5baud init if panda adds support for 5bps serial)*
-
-# Building the Project:
-
-This project is developed with Visual Studio 2017, the Windows SDK,
-and the Windows Driver Kit (WDK).
-
-The WDK is only required for creating the signed WinUSB inf file. The
-WDK may also provide the headers for WinUSB.
-
-To build all the projects required for the installer, in Visual
-Studio, select **Build->Batch Build.** In the project list select:
-
-- **"panda"** *Release|x86*
-- **"panda"** *Release|x64*
-- **"panda Driver Package"** Debug|x86 (Note this inf file works with x86/amd64).
-- **"pandaJ2534DLL"** *Release|x86*
-
-The installer is generated with [NullSoft NSIS](http://nsis.sourceforge.net/Main_Page).
-Use NSIS to run panda_install.nsi after building all the required projects.
-
-Before generating the installer, you must go to copy vscruntimeinfo.nsh.sample to
-vscruntimeinfo.nsh and follow the instructions to bundle in the Visual Studio C
-Runtime required by your version of Visual Studio. Without this runtime, the panda
-code will not work, so without this file, the installer will refuse to build.
-
-# Developing:
-
-- Edit and merge pandaJ2534DLL\J2534register_x64.reg to register your development J2534 DLL.
-- Add your output directory (panda\drivers\windows\Debug_x86) to your system PATH to avoid insanity.
-
-# ToDo Items:
-
-- Apply a style-guide and consistent naming convention for Classes/Functions/Variables.
-- Send multiple messages (each with a different address) from a given connection at the same time.
-- Implement ISO14230/KWP2000 FAST (LIN communication is already supported with the raw panda USB driver).
-- Find more documentation about SW_CAN_PS (Single Wire CAN, aka GMLAN).
-- Find example of client using a _PS version of a protocol (PS is pin select, and may support using different CAN buses).
-
-
-# Known Issues:
-
-- ISO15765 Multi-frame TX: Hardware delays make transmission overshoot
- STMIN by several milliseconds. This does not violate the requirements
- of STMIN, it just means it is a little slower than it could be.
-
-- All Tx messages from a single Connection are serialized. This can be
- relaxed to allow serialization of messages based on their address
- (making multiple queues, effectively one queue per address).
-
-# Troubleshooting:
-troubleshooting:
-1. Install DrewTech J2534-1 Bus Analysis Tool
-http://www.drewtech.com/downloads/tools/Drew%20Technologies%20Tool%20for%20J2534-1%20API%20v1.07.msi
-2. Open DrewTech tool and make sure it shows "panda" as a device listed (this means registry settings are correct)
-3. When DrewTech tool attempts to load the driver it will show an error if it fails
-4. To figure out why the driver fails to load install Process Monitor and filter by the appropriate process name
-https://docs.microsoft.com/en-us/sysinternals/downloads/procmon
-
-# Other:
-Panda head ASCII art by dcau
\ No newline at end of file
diff --git a/panda/drivers/windows/docs/Message_Size.png b/panda/drivers/windows/docs/Message_Size.png
deleted file mode 100644
index 3a20a2ef3..000000000
Binary files a/panda/drivers/windows/docs/Message_Size.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/RxBits_defs.jpg b/panda/drivers/windows/docs/RxBits_defs.jpg
deleted file mode 100644
index db01f62c9..000000000
Binary files a/panda/drivers/windows/docs/RxBits_defs.jpg and /dev/null differ
diff --git a/panda/drivers/windows/docs/RxBits_valid.png b/panda/drivers/windows/docs/RxBits_valid.png
deleted file mode 100644
index 6f7c4c326..000000000
Binary files a/panda/drivers/windows/docs/RxBits_valid.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/bus_init_signla.png b/panda/drivers/windows/docs/bus_init_signla.png
deleted file mode 100644
index 9aa71faa2..000000000
Binary files a/panda/drivers/windows/docs/bus_init_signla.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/connection_flags.png b/panda/drivers/windows/docs/connection_flags.png
deleted file mode 100644
index dd578a2cb..000000000
Binary files a/panda/drivers/windows/docs/connection_flags.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/iso15765_ioctls.png b/panda/drivers/windows/docs/iso15765_ioctls.png
deleted file mode 100644
index 7de4a118e..000000000
Binary files a/panda/drivers/windows/docs/iso15765_ioctls.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/message_send.png b/panda/drivers/windows/docs/message_send.png
deleted file mode 100644
index 112aab14c..000000000
Binary files a/panda/drivers/windows/docs/message_send.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/msg_filter_passfail.png b/panda/drivers/windows/docs/msg_filter_passfail.png
deleted file mode 100644
index 4a91facb4..000000000
Binary files a/panda/drivers/windows/docs/msg_filter_passfail.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/other notes.txt b/panda/drivers/windows/docs/other notes.txt
deleted file mode 100644
index a066d2646..000000000
--- a/panda/drivers/windows/docs/other notes.txt
+++ /dev/null
@@ -1,347 +0,0 @@
-When using the ISO 15765-4 protocol, only SingleFrame messages can be transmitted without a matching
-flow control filter. Also, PCI bytes are transparently added by the API. See PassThruStartMsgFilter
-and Appendix A for a discussion of flow control filters.
-
-
-
-PassThruReadMsgs
-This function reads messages and indications from the receive buffer. All messages and indications shall
-be read in the order that they occurred on the bus. If a transmit message generated a loopback message
-and TxDone indication, the TxDone indication shall always be queued first. Except for loopback messages
-and indications, no messages shall be queued for reception without matching a PASS_FILTER
-(for non-ISO 15765) or FLOW_CONTROL filter (for ISO 15765). On ISO 15765, PCI bytes are transparently
-removed by the API. If the function is successful, a value of STATUS_NOERROR is returned.
-
-
-PassThruWriteMsgs
-Write timeout (in milliseconds). When a value of 0 is specified, the function queues as
-many of the specified messages as possible and returns immediately. When a value
-greater than 0 is specified, the function will block until the Timeout has expired, an error
-has occurred, or the desired number of messages have been transmitted on the vehicle
-network. Even if the device can buffer only one packet at a time, this function shall be
-able to send an arbitrary number of packets if a Timeout value is supplied. Since the
-function returns early if all the messages have been sent, there is normally no penalty for
-having a large timeout (several seconds). If the number of messages requested have
-been written, the function shall not return ERR_TIMEOUT, even if the timeout value is
-zero.
-
-When an ERR_TIMEOUT is returned, only the number of messages that were sent on
-the vehicle network is known. The number of messages queued is unknown. Application
-writers should avoid this ambiguity by using a Timeout value large enough to work on
-slow devices and networks with arbitration delays.
-
-
-
-PassThruStartPeriodicMsg
-This function will immediately queue the specified message for transmission, and repeat at the specified
-interval. Periodic messages are limited in length to a single frame message of 12 bytes or less, including
-header or CAN ID. Periodic messages shall have priority over messages queued with
-PassThruWriteMsgs, but periodic messages must not violate bus idle timing parameters (e.g. P3_MIN).
-Periodic messages shall generate TxDone indications (ISO 15765) and loopback messages (on any
-protocol, if enabled). On ISO 15765, periodic messages can be sent during a multi-frame transmission or
-reception. If the function is successful, a value of STATUS_NOERROR is returned. The Pass-Thru
-device must support a minimum of ten periodic messages.
-
-PassThruDisconnect shall delete all periodic messages on that channel. PassThruClose shall delete all
-periodic messages on all channels for the device. All periodic messages will be stopped on a
-PassThruDisconnect for the associated protocol or a PassThruClose for the device.
-
-
-
-PASSTHRUSTARTMSGFILTER
-This function starts filtering of incoming messages. If the function is successful, a value of
-STATUS_NOERROR is returned. A minimum of ten message filters shall be supported by the interface
-for each supported protocol. PassThruDisconnect shall delete all message filters on that channel.
-
-PassThruClose shall delete all filters on all channels for the device. Pattern and Mask messages shall
-follow the protocol formats specified in Section 8. However, only the first twelve (12) bytes, including
-header or CAN ID, are used by the filter. ERR_INVALID_MSG shall be returned if the filter length
-exceeds 12. Note that this function does not clear any messages that may have been received and
-queued before the filter was set. Users are cautioned to consider performing a CLEAR_RX_BUFFER
-after starting a message filter to be sure that unwanted frames are purged from any receive buffers.
-
-
-
-
-
-
-
-
-FILTER RELATED STUFF
-For all protocols except ISO 15765:
-• PASS_FILTERs and BLOCK_FILTERs will be applied to all received messages. They shall not be
-applied to indications or loopback messages
-
-• FLOW_CONTROL_FILTERs must not be used and shall cause the interface to return
-ERR_INVALID_FILTER_ID
-
-• Both pMaskMsg and pPatternMsg must have the same DataSize and TxFlags. Otherwise, the
-interface shall return ERR_INVALID_MSG
-
-• The default filter behavior after PassThruConnect is to block all messages, which means no messages
-will be placed in the receive queue until a PASS_FILTER has been set. Messages that match a
-PASS_FILTER can still be blocked by a BLOCK_FILTER
-
-• Figure 16 and Figure 17 show how the message filtering mechanism operates
-
-For ISO 15765:
-• PASS_FILTERs and BLOCK_FILTERs must not be used and shall cause the interface to return
-ERR_INVALID_FILTER_ID
-
-• Filters shall not be applied to indications or loopback messages. When loopback is on, the original
-message shall be copied to the receive queue upon the last segment being transmitted on the bus.
-
-• Non-segmented messages do not need to match a FLOW_CONTROL_FILTER.
-
-• No segmented messages can be transmitted without matching an appropriate FLOW_CONTROL_FILTER.
-An appropriate filter is one in which the pFlowControlMsg CAN ID matches the messages to be
-transmitted. Also, the ISO 15765_ADDR_TYPE (reference TxFlags in Section 8.7.3) bits must match.
-If that bit is set, the first byte after the CAN IDs (the extended address)
-must match too.
-
-• No message (segmented or unsegmented) shall be received without matching an appropriate
-FLOW_CONTROL_FILTER. An appropriate filter is one in which the pPatternMsg CAN ID matches
-the incoming message ID. If the ISO 15765_ADDR_TYPE (reference TxFlags in Section 8.7.3) bit is
-set in the filter, the first byte after the CAN IDs (the extended address) must match too.
-
-• All 3 message pointers must have the same DataSize and TxFlags. Otherwise, the interface shall
-return ERR_INVALID_MSG.
-
-• Both the pFlowControlMsg ID and the pPatternMsg ID must be unique (not match any IDs in any other
-filters). The only exception is that pPatternMsg can equal pFlowControlMsg to allow for receiving
-functionally addressed messages. In this case, only non-segmented messages can be received.
-
-• See Appendix A for a detailed description of flow control filter usage.
-
-
-
-
-8.4 Format Checks for Messages Passed to the API
-The vendor DLL shall validate all PASSTHRU_MSG structures, and return an ERR_INVALID_MSG in the following cases:
-• DataSize violates Min Tx or Max Tx columns in Figure 42
-
-• Source address (Data[3]) is different from the Node ID (Ioctl SET_CONFIG, Parameter NODE_ADDRESS) on J1850PWM
-
-• The header length field is incorrect for the number of bytes in the message on ISO14230
-
-• The CAN_29_BIT flag of the message does not match the CAN_29_BIT flag passed to
-PassThruConnect, unless the CAN_ID_BOTH bit was set on connect
-
-The vendor DLL shall return ERR_MSG_PROTOCOL_ID when the ProtocolID field in the message does
-not match the Protocol ID specified when opening the channel.
-
-
-
-8.5 Conventions for Returning Messages from the API
-When returning a message in PassThruReadMsg:
-– DataSize shall tell the application how many bytes in the Data array are valid. ExtraDataIndex will be
-the (non-zero) index of the last byte of the message. If ExtraDataIndex is not equal to DataSize there
-are extra data bytes after the message. If loopback is on, RxStatus must be consulted to tell if the
-message came via loopback.
-
-– DataSize will be in the range shown in the Min Rx and Max Rx columns of Figure 42. If the device
-receives a message from the vehicle bus that is too long or too short, the message shall be discarded
-with no error.
-
-– For received messages, ExtraDataIndex shall be equal to DataSize, except when the interface is
-returning SAE J1850 PWM IFR bytes. In no case shall ExtraDataIndex be larger than DataSize.
-
-– When receiving a message on an SAE J1850 PWM channel, the message shall have any IFR bytes
-appended. In this case, ExtraDataIndex shall be the index of the first IFR byte, and DataSize shall be
-the total length of the original message plus all IFR bytes. For example, if there are two IFR bytes,
-DataSize will be incremented by two, and ExtraDataIndex will be DataSize - 2. When loopback is on,
-the loopback message shall contain any IFR bytes.
-
-
-
-8.6 Conventions for Retuning Indications from the API
-When returning an indication in PassThruReadMsg:
-– ExtraDataIndex must be zero
-
-– DataSize shall tell the application how many bytes in the Data array are valid
-
-– RxStatus must be consulted to determine the indication type (See Section 8.4).
-
-– A TxDone indication (ISO 15765 only) is generated by the DLL after a SingleFrame message is sent,
-or the last frame of a multi-segment transmission is sent. DataSize shall be 4 (or 5 when the message
-was using Extended Addressing). Data shall contain the CAN ID (and possible Extended Address) of
-the message just sent. If loopback is on, the TxDone indication shall precede the loopback message in
-the receive queue.
-
-– An RxBreak indication (SAE J2610/SCI and SAE J1850VPW only) is generated by the DLL if a break
-is received.
-
-– An RxStart indication is generated by the DLL when starting to receive a message on ISO9141 or
-ISO14230, or when receiving the FirstFrame signal of a multi-segment ISO 15765 message.
-
-
-
-9.1 Naming of Files
-Each vendor will provide a different name implementation of the API DLL and a number of these
-implementations could simultaneously reside on the same PC. No vendor shall name its implementation
-“J2534.DLL”. All implementations shall have the string “32” suffixed to end of the name of the API DLL to
-indicate 32-bit. For example, if the company name is “Vendor X” the name could be VENDRX32.DLL.
-
-For simplicity, an API DLL shall be named in accordance with the file allocation table (FAT) file system
-naming convention (which allows up to eight characters for the file name and three characters for the
-extension with no spaces anywhere). Note that, given this criteria, the major name of an API DLL can be
-no greater than six characters. The OEM application can determine the name of the appropriate vendor’s
-DLL using the Win32 Registry mechanism described in this section.
-
-
-
-
-A.1 Flow Control Overview
-ISO 15765-2 was designed to send blocks of up to 4095 bytes on top of the limited 8-byte payload of raw
-CAN frames. If the data is small enough, it can fit in a single frame and be transmitted like a raw CAN
-message with additional headers. Otherwise, the block is broken up into segments and becomes a
-segmented transmission, generating CAN frames in both directions. For flexibility, the receiver of the
-segments can control the rate at which the segments are sent.
-
-Each transmission is actually part of a conversation between two nodes. There is no discovery
-mechanism for conversation partners. Therefore, each desired conversation must be pre-defined on each
-side before the conversation can start. Conversations are symmetric, meaning that either side can send a
-block of data to the other. A conversation can only have one transfer (in one direction) in progress at a
-time. One transfer must complete before the next transfer (in the same or in a different direction) can
-start. The device must support multiple transfers at once, as long as each one is part of a different
-conversation. Raw CAN frames are not allowed when using ISO15765-2.
-
-A key feature of a conversation is that each side has a unique CAN ID, and each side uses their unique
-CAN ID for all transmissions during the conversation. No other CAN IDs are part of the conversation.
-Even though the useful data is only flowing in one direction, both sides are transmitting. One side is
-sending the flow control message to pace the segments of data coming from the other side.
-
-For example, during OBD communication, a pass-thru device and an ECU might have a conversation.
-The pass-thru device will use the "Tester1" physical CAN ID ($241), and the first ECU will use the
-"ECU1" physical CAN ID ($641). During a multi-segment transfer, both sides will be transmitting using
-only their respective IDs. It does not matter if the data is being sent by the ECU or by the Tester, the IDs
-remain the same.
-
-It is important to understand the difference between OBD Requests/Responses and ISO 15765-2
-transfers. The OBD Request is transmitted from the Tester to the ECU using functional addressing.
-Because segmented transfer is not possible on functional addresses, the message must fit in a single
-frame. The OBD Response is a message from the ECU to the Tester using physical addressing. Unlike
-other protocols, the responses are not sequential. In fact, the responses can overlap, as if each ECU
-were having a private conversation with the Tester. Some of the responses may fit in a single frame,
-while others will require a segmented transfer from the ECU to the tester.
-
-
-A.2 Transmitting a Segmented Message
-When PassThruWrite is called, the API will search the list of flow control filters, looking for a
-pFlowControlMsg that matches the CAN ID (and possible extended address) of the message being sent.
-Upon matching a filter, the pass-thru device will:
-
-• Start the ISO 15765 transfer by sending a FirstFrame on the bus. The CAN ID of this segment was
-specified in both the message and the matching pFlowControlMsg. In our example, this is $241.
-
-• Wait for a FlowControl frame from the conversation partner. The CAN ID to look for is specified in the
-corresponding pPatternMsg. In our example, this is $641.
-
-• Transmit the message data in ConsecutiveFrames according to the FlowControl frame’s instructions
-for BS (BlockSize) and STmin (SeparationTime minimum). Again, the pass-thru device transmits using
-CAN ID specified in pFlowControlMsg. In our example, this is $241.
-
-• Repeat the previous two steps as required.
-
-• When finished, the pass-thru device will place a TxDone indication in the API receive queue. The data
-will contain the CAN ID specified in pFlowControlMsg. In our example, this is $241.
-
-• If loopback is on, the entire message sent will appear in the API receive queue with the
-TX_MSG_TYPE bit set to 1 in RxStatus. The loopback shall not precede the TxDone indication.
-
-Before any multi-segment transfer can take place, the conversation must be set up on both sides. It’s
-assumed that the ECU is already setup. The application is responsible for setting up the pass-thru device.
-This setup must be done once (and only once) per conversation. The setup involves a single call to
-PassThruStartMsgFilter, with the following parameters:
-
-A.2.2 Data Transmission
-Once the conversation is set up, any number of messages (to the conversation partner) can be
-transmitted using PassThruWriteMsg. The interface shall handle all aspects of the transfer, including
-pacing (slowing) the transmission to the requirements of the receiver.
-
-When there are multiple conversations setup, the pass-thru device will search all of the flow control filters
-for a matching pFlowControlMsg. If there is no match, the message cannot be sent because the pass-
-thru device doesn’t know which partner will be pacing the conversation.
-
-When doing blocking writes, it is important to pick a timeout long enough to cover entire transfer, even if
-the ECU is pacing things slowly. Otherwise PassThruWriteMsg will return with a timeout, even though the
-transmission is proceeding normally.
-
-
-A.3 Transmitting an Unsegmented Message
-As a special case, transfers that fit in a single frame can be transmitted without setting up a conversation.
-This is useful during an OBD Request, which is a functionally addressed message that is broadcast to all
-ECUs. This message must be small enough to fit into a single frame (including headers) because it is not
-possible to do one segmented transfer to multiple ECUs.
-
-When using functional addressing for an OBD Request, it is important to remember that there can be no
-direct reply. Instead, each ECU will send their OBD Response using physical addressing to their
-conversation partner (e.g. ECU1 to Tester1, ECU2 to Tester2) as defined by ISO 15765-4. The OBD
-Response may be a segmented transfer, or it may be a single frame.
-
-In this case, no conversation setup is necessary. The call to PassThruWriteMsg is the same as above,
-except that the DataSize must be 7 bytes or less (6 bytes or less if extended addressing is turned on).
-The pass-thru device will automatically insert a PCI byte before transmission.
-
-
-A.4 Receiving a Segmented Message
-Message reception is asynchronous to the application. When a FirstFrame is seen on the bus, the pass-
-thru device will search the list of flow control filters, looking for a pPatternMsg message with the same
-CAN ID (and possible extended address) as the FirstFrame. Upon matching a filter, the pass-thru device will:
-
-• Place an RxStart indication in the API receive queue. This indication has the START_OF_MESSAGE
-bit set in RxFlags. The message data will contain the CAN ID of the sender. In our example, this is
-$641. DataSize will be 4 bytes (5 with extended addressing), and ExtraDataIndex will be zero.
-
-• Send a FlowControl frame to the conversation partner. The FlowStatus field shall be set to
-ontinueToSend. The CAN ID of this segment comes from the filter’s corresponding
-pFlowControlMsg. In our example, this CAN ID is $241. The BS (BlockSize) and STmin
-(SeparationTime minimum) parameters default to zero, but can be changed with the SET_CONFIGIoctl.
-
-• Wait for the conversation partner to send C
-onsecutiveFrames containing the actual data. The
-partner’s CAN ID is specified in pPatternMsg. In our example, this CAN ID is $641.
-
-• Repeat as necessary until the entire block has been received. When finished, the pass-thru device will
-put the assembled message into the API receive queue. The CAN ID of the assembled message will
-be the CAN ID of the sender. In our example, this CAN ID is $641.
-
-If the FirstFrame does not match any flow control filters, then the message must be ignored by the
-device.
-
-Segmented messages cause the API to generate an RxStart indication. This lets the application know
-that the device has started message reception. It may take a while before message reception is
-complete, especially if the application has increased BS and STmin.
-
-Once the transfer is complete, the entire message can be read like on any other protocol. Usually,
-applications will call PassThruReadMsg again immediately after getting an RxStart indication. Application
-writers should not assume that the complete message will always follow the RxStart indication. If multiple
-conversations are setup, indications and messages from other conversations can be received in between
-the RxStart indication and the actual message. The parameters for PassThruReadMsg are exactly the
-same as in the previous section. The only difference is that the DataSize will be larger and
-ExtraDataIndex will be non-zero.
-
-
-
-A.5 Receiving an Unsegmented Message
-No messages can be received until a conversation is setup. Each conversation setup will receive
-messages from exactly one CAN ID (and extended address if present). Because setup is bi-directional,
-the same PassThruStartMsgFilter call used for transmission will allow for message reception.
-
-When a SingleFrame is seen on the bus, the pass-thru device will search the list of flow control filters,
-looking for a pPatternMsg message with the same C
-AN ID (and possible extended address) as the
-SingleFrame. Upon matching a filter, the pass-thru device will strip the PCI byte and queue the packet for
-reception. If the SingleFrame does not match a flow control filter, it must be discarded.
-
-The only difference between the previous cases is that single-frame messages do not generate an
-RxStart indication.
-
-
-
-
-
-
-
-
-
diff --git a/panda/drivers/windows/docs/read_msg_flags.png b/panda/drivers/windows/docs/read_msg_flags.png
deleted file mode 100644
index 6d0a1f874..000000000
Binary files a/panda/drivers/windows/docs/read_msg_flags.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/reginfo.txt b/panda/drivers/windows/docs/reginfo.txt
deleted file mode 100644
index 03182832b..000000000
--- a/panda/drivers/windows/docs/reginfo.txt
+++ /dev/null
@@ -1,2 +0,0 @@
-#32 bit: HKEY_LOCAL_MACHINE\SOFTWARE\PassThruSupport
-#64 bit: HKEY_LOCAL_MACHINE\SOFTWARE\WOW6432Node\PassThruSupport
diff --git a/panda/drivers/windows/docs/start_msg_filter.png b/panda/drivers/windows/docs/start_msg_filter.png
deleted file mode 100644
index 7cb1a7a4c..000000000
Binary files a/panda/drivers/windows/docs/start_msg_filter.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/start_msg_filter2.png b/panda/drivers/windows/docs/start_msg_filter2.png
deleted file mode 100644
index 54063a507..000000000
Binary files a/panda/drivers/windows/docs/start_msg_filter2.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/start_msg_filter3.png b/panda/drivers/windows/docs/start_msg_filter3.png
deleted file mode 100644
index ffc8e3482..000000000
Binary files a/panda/drivers/windows/docs/start_msg_filter3.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/start_msg_filter4.png b/panda/drivers/windows/docs/start_msg_filter4.png
deleted file mode 100644
index 9c21fb014..000000000
Binary files a/panda/drivers/windows/docs/start_msg_filter4.png and /dev/null differ
diff --git a/panda/drivers/windows/docs/timeout_info.txt b/panda/drivers/windows/docs/timeout_info.txt
deleted file mode 100644
index 22cfa2c5d..000000000
--- a/panda/drivers/windows/docs/timeout_info.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-From focum information on NI hardware: https://forums.ni.com/t5/Automotive-and-Embedded-Networks/15765-2-with-NI-products/td-p/1454256
-
-/////////////////////////////////////////////////////////////////////
-Timeout Diag Command is the timeout in milliseconds the master
-waits for the response to a diagnostic request message. The default is
-1000 ms.
-
-Timeout FC (Bs) is the timeout in milliseconds the master waits
-for a Flow Control frame after sending a First Frame or the last
-Consecutive Frame of a block. The default is 250 ms.
-
-Timeout CF (Cr) is the timeout in milliseconds the master waits
-for a Consecutive Frame in a multiframe response. The default is
-250 ms.
-
-Receive Block Size (BS) is the number of Consecutive Frames the
-slave sends in one block before waiting for the next Flow Control
-frame. A value of 0 (default) means all Consecutive Frames are sent
-in one run without interruption.
-
-Wait Time CF (STmin) defines the minimum time for the slave to
-wait between sending two Consecutive Frames of a block. Values
-from 0 to 127 are wait times in milliseconds. Values 241 to 249
-(Hex F1 to F9) mean wait times of 100 μs to 900 μs, respectively.
-All other values are reserved. The default is 5 ms.
-
-Max Wait Frames (N_WFTmax) is the maximum number of WAIT
-frames the master accepts before terminating the connection. The
-default is 10.
-
-
-There are no defined lower limits for these values; you can specify any
-value down to 0. However, as you correctly pointed out, the timing is
-done by Windows, and will be subject to the jitter introduced by the OS
-which can easily be in the order of 10s of milliseconds. It is however
-hard to give more accurate numbers as the actual jitter is dependent on
-the workload of the computer
-/////////////////////////////////////////////////////////////////////
-
-J2534 04.04 does not appear to have default adjustable parameters for
-the timeout related fields. For now, these default values shall be used
-in the Panda J2534 implementation.
diff --git a/panda/drivers/windows/panda Driver Package/panda Driver Package.vcxproj b/panda/drivers/windows/panda Driver Package/panda Driver Package.vcxproj
deleted file mode 100644
index 5b448e96a..000000000
--- a/panda/drivers/windows/panda Driver Package/panda Driver Package.vcxproj
+++ /dev/null
@@ -1,99 +0,0 @@
-
-
-
-
- Debug
- Win32
-
-
- Release
- Win32
-
-
-
- {BD34DB24-F5DC-4992-A74F-05FAF731ABED}
- {a1357fe7-03e0-4d61-85f4-09c7ed38c0c1}
- v4.5
- 12.0
- $driverCurrentWindowsConfigurationName$ Debug
- Win32
- panda_Driver_Package
- $(LatestTargetPlatformVersion)
-
-
- Windows10
- true
- WindowsKernelModeDriver10.0
- Utility
- Package
- true
-
-
- Windows10
- false
- WindowsKernelModeDriver10.0
- Utility
- Package
- true
-
-
-
-
-
-
-
- DbgengRemoteDebugger
- False
- False
- True
- 133563
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
-
- DbgengRemoteDebugger
- False
- False
- True
- 133563
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
-
-
-
-
-
-
-
- $(KMDF_VERSION_MAJOR).$(KMDF_VERSION_MINOR)
-
-
-
-
-
-
- $(KMDF_VERSION_MAJOR).$(KMDF_VERSION_MINOR)
-
-
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/panda Driver Package/panda Driver Package.vcxproj.filters b/panda/drivers/windows/panda Driver Package/panda Driver Package.vcxproj.filters
deleted file mode 100644
index b4cf07798..000000000
--- a/panda/drivers/windows/panda Driver Package/panda Driver Package.vcxproj.filters
+++ /dev/null
@@ -1,14 +0,0 @@
-
-
-
-
- {8E41214B-6785-4CFE-B992-037D68949A14}
- inf;inv;inx;mof;mc;
-
-
-
-
- Driver Files
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/panda Driver Package/panda.inf b/panda/drivers/windows/panda Driver Package/panda.inf
deleted file mode 100644
index 69390dcbc..000000000
Binary files a/panda/drivers/windows/panda Driver Package/panda.inf and /dev/null differ
diff --git a/panda/drivers/windows/panda.ico b/panda/drivers/windows/panda.ico
deleted file mode 100644
index 593a5cd33..000000000
Binary files a/panda/drivers/windows/panda.ico and /dev/null differ
diff --git a/panda/drivers/windows/panda.sln b/panda/drivers/windows/panda.sln
deleted file mode 100644
index 39c8a63e2..000000000
--- a/panda/drivers/windows/panda.sln
+++ /dev/null
@@ -1,92 +0,0 @@
-
-Microsoft Visual Studio Solution File, Format Version 12.00
-# Visual Studio 15
-VisualStudioVersion = 15.0.27130.2027
-MinimumVisualStudioVersion = 10.0.40219.1
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "pandaJ2534DLL", "pandaJ2534DLL\pandaJ2534DLL.vcxproj", "{A2BB18A5-F26B-48D6-BBB5-B83D64473C77}"
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "panda", "panda\panda.vcxproj", "{5528AEFB-638D-49AF-B9D4-965154E7D531}"
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "panda_playground", "panda_playground\panda_playground.vcxproj", "{691DB635-C272-4B98-897E-0505B970DCA9}"
- ProjectSection(ProjectDependencies) = postProject
- {5528AEFB-638D-49AF-B9D4-965154E7D531} = {5528AEFB-638D-49AF-B9D4-965154E7D531}
- EndProjectSection
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "panda Driver Package", "panda Driver Package\panda Driver Package.vcxproj", "{BD34DB24-F5DC-4992-A74F-05FAF731ABED}"
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "Tests", "pandaJ2534DLL Test\pandaJ2534DLL Test.vcxproj", "{7912F978-B48C-4C5D-8BFD-5D1E22158E47}"
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "ECUsim DLL", "ECUsim DLL\ECUsim DLL.vcxproj", "{96E0E646-EE76-444D-9A77-A0CD7F781DEB}"
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "ECUsim CLI", "ECUsim CLI\ECUsim CLI.vcxproj", "{D99E2FCD-21A4-4065-949A-31E34E0E69D1}"
-EndProject
-Project("{8BC9CEB8-8B4A-11D0-8D11-00A0C91BC942}") = "panda_shared", "panda_shared\panda_shared.vcxitems", "{0C843279-68C7-4679-AE51-9BC463D50D1C}"
-EndProject
-Global
- GlobalSection(SharedMSBuildProjectFiles) = preSolution
- panda_shared\panda_shared.vcxitems*{0c843279-68c7-4679-ae51-9bc463d50d1c}*SharedItemsImports = 9
- panda_shared\panda_shared.vcxitems*{5528aefb-638d-49af-b9d4-965154e7d531}*SharedItemsImports = 4
- panda_shared\panda_shared.vcxitems*{a2bb18a5-f26b-48d6-bbb5-b83d64473c77}*SharedItemsImports = 4
- EndGlobalSection
- GlobalSection(SolutionConfigurationPlatforms) = preSolution
- Debug|x64 = Debug|x64
- Debug|x86 = Debug|x86
- Release|x64 = Release|x64
- Release|x86 = Release|x86
- EndGlobalSection
- GlobalSection(ProjectConfigurationPlatforms) = postSolution
- {A2BB18A5-F26B-48D6-BBB5-B83D64473C77}.Debug|x64.ActiveCfg = Debug|Win32
- {A2BB18A5-F26B-48D6-BBB5-B83D64473C77}.Debug|x86.ActiveCfg = Debug|Win32
- {A2BB18A5-F26B-48D6-BBB5-B83D64473C77}.Debug|x86.Build.0 = Debug|Win32
- {A2BB18A5-F26B-48D6-BBB5-B83D64473C77}.Release|x64.ActiveCfg = Release|Win32
- {A2BB18A5-F26B-48D6-BBB5-B83D64473C77}.Release|x86.ActiveCfg = Release|Win32
- {A2BB18A5-F26B-48D6-BBB5-B83D64473C77}.Release|x86.Build.0 = Release|Win32
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Debug|x64.ActiveCfg = Debug|x64
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Debug|x64.Build.0 = Debug|x64
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Debug|x86.ActiveCfg = Debug|Win32
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Debug|x86.Build.0 = Debug|Win32
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Release|x64.ActiveCfg = Release|x64
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Release|x64.Build.0 = Release|x64
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Release|x86.ActiveCfg = Release|Win32
- {5528AEFB-638D-49AF-B9D4-965154E7D531}.Release|x86.Build.0 = Release|Win32
- {691DB635-C272-4B98-897E-0505B970DCA9}.Debug|x64.ActiveCfg = Debug|x64
- {691DB635-C272-4B98-897E-0505B970DCA9}.Debug|x64.Build.0 = Debug|x64
- {691DB635-C272-4B98-897E-0505B970DCA9}.Debug|x86.ActiveCfg = Debug|Win32
- {691DB635-C272-4B98-897E-0505B970DCA9}.Debug|x86.Build.0 = Debug|Win32
- {691DB635-C272-4B98-897E-0505B970DCA9}.Release|x64.ActiveCfg = Release|x64
- {691DB635-C272-4B98-897E-0505B970DCA9}.Release|x64.Build.0 = Release|x64
- {691DB635-C272-4B98-897E-0505B970DCA9}.Release|x86.ActiveCfg = Release|Win32
- {BD34DB24-F5DC-4992-A74F-05FAF731ABED}.Debug|x64.ActiveCfg = Debug|Win32
- {BD34DB24-F5DC-4992-A74F-05FAF731ABED}.Debug|x86.ActiveCfg = Debug|Win32
- {BD34DB24-F5DC-4992-A74F-05FAF731ABED}.Release|x64.ActiveCfg = Release|Win32
- {BD34DB24-F5DC-4992-A74F-05FAF731ABED}.Release|x86.ActiveCfg = Release|Win32
- {7912F978-B48C-4C5D-8BFD-5D1E22158E47}.Debug|x64.ActiveCfg = Debug|Win32
- {7912F978-B48C-4C5D-8BFD-5D1E22158E47}.Debug|x86.ActiveCfg = Debug|Win32
- {7912F978-B48C-4C5D-8BFD-5D1E22158E47}.Debug|x86.Build.0 = Debug|Win32
- {7912F978-B48C-4C5D-8BFD-5D1E22158E47}.Release|x64.ActiveCfg = Release|Win32
- {7912F978-B48C-4C5D-8BFD-5D1E22158E47}.Release|x86.ActiveCfg = Release|Win32
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Debug|x64.ActiveCfg = Debug|x64
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Debug|x64.Build.0 = Debug|x64
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Debug|x86.ActiveCfg = Debug|Win32
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Debug|x86.Build.0 = Debug|Win32
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Release|x64.ActiveCfg = Release|x64
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Release|x64.Build.0 = Release|x64
- {96E0E646-EE76-444D-9A77-A0CD7F781DEB}.Release|x86.ActiveCfg = Release|Win32
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Debug|x64.ActiveCfg = Debug|x64
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Debug|x64.Build.0 = Debug|x64
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Debug|x86.ActiveCfg = Debug|Win32
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Debug|x86.Build.0 = Debug|Win32
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Release|x64.ActiveCfg = Release|x64
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Release|x64.Build.0 = Release|x64
- {D99E2FCD-21A4-4065-949A-31E34E0E69D1}.Release|x86.ActiveCfg = Release|Win32
- EndGlobalSection
- GlobalSection(SolutionProperties) = preSolution
- HideSolutionNode = FALSE
- EndGlobalSection
- GlobalSection(ExtensibilityGlobals) = postSolution
- SolutionGuid = {8AF3826E-406A-4F1C-BA80-B4D7FD4B52E1}
- EndGlobalSection
- GlobalSection(Performance) = preSolution
- HasPerformanceSessions = true
- EndGlobalSection
-EndGlobal
diff --git a/panda/drivers/windows/panda/dllmain.cpp b/panda/drivers/windows/panda/dllmain.cpp
deleted file mode 100644
index 69b58914b..000000000
--- a/panda/drivers/windows/panda/dllmain.cpp
+++ /dev/null
@@ -1,19 +0,0 @@
-// dllmain.cpp : Defines the entry point for the DLL application.
-#include "stdafx.h"
-
-BOOL APIENTRY DllMain( HMODULE hModule,
- DWORD ul_reason_for_call,
- LPVOID lpReserved
- )
-{
- switch (ul_reason_for_call)
- {
- case DLL_PROCESS_ATTACH:
- case DLL_THREAD_ATTACH:
- case DLL_THREAD_DETACH:
- case DLL_PROCESS_DETACH:
- break;
- }
- return TRUE;
-}
-
diff --git a/panda/drivers/windows/panda/main.cpp b/panda/drivers/windows/panda/main.cpp
deleted file mode 100644
index 621c600b8..000000000
--- a/panda/drivers/windows/panda/main.cpp
+++ /dev/null
@@ -1,79 +0,0 @@
-#include "stdafx.h"
-
-#include
-
-LONG __cdecl
-_tmain(
- LONG Argc,
- LPTSTR * Argv
- )
-/*++
-
-Routine description:
-
- Sample program that communicates with a USB device using WinUSB
-
---*/
-{
- DEVICE_DATA deviceData;
- HRESULT hr;
- USB_DEVICE_DESCRIPTOR deviceDesc;
- BOOL bResult;
- BOOL noDevice;
- ULONG lengthReceived;
-
- UNREFERENCED_PARAMETER(Argc);
- UNREFERENCED_PARAMETER(Argv);
-
- //
- // Find a device connected to the system that has WinUSB installed using our
- // INF
- //
- hr = OpenDevice(&deviceData, &noDevice);
-
- if (FAILED(hr)) {
-
- if (noDevice) {
-
- printf(_T("Device not connected or driver not installed\n"));
-
- } else {
-
- printf(_T("Failed looking for device, HRESULT 0x%x\n"), hr);
- }
-
- return 0;
- }
-
- //
- // Get device descriptor
- //
- bResult = WinUsb_GetDescriptor(deviceData.WinusbHandle,
- USB_DEVICE_DESCRIPTOR_TYPE,
- 0,
- 0,
- (PBYTE) &deviceDesc,
- sizeof(deviceDesc),
- &lengthReceived);
-
- if (FALSE == bResult || lengthReceived != sizeof(deviceDesc)) {
-
- printf(_T("Error among LastError %d or lengthReceived %d\n"),
- FALSE == bResult ? GetLastError() : 0,
- lengthReceived);
- CloseDevice(&deviceData);
- return 0;
- }
-
- //
- // Print a few parts of the device descriptor
- //
- printf(_T("Device found: VID_%04X&PID_%04X; bcdUsb %04X; path: %s\n"),
- deviceDesc.idVendor,
- deviceDesc.idProduct,
- deviceDesc.bcdUSB,
- deviceData.DevicePath);
-
- CloseDevice(&deviceData);
- return 0;
-}
diff --git a/panda/drivers/windows/panda/panda.ico b/panda/drivers/windows/panda/panda.ico
deleted file mode 100644
index ff0e071f5..000000000
Binary files a/panda/drivers/windows/panda/panda.ico and /dev/null differ
diff --git a/panda/drivers/windows/panda/panda.rc b/panda/drivers/windows/panda/panda.rc
deleted file mode 100644
index 88cf9f767..000000000
Binary files a/panda/drivers/windows/panda/panda.rc and /dev/null differ
diff --git a/panda/drivers/windows/panda/panda.vcxproj b/panda/drivers/windows/panda/panda.vcxproj
deleted file mode 100644
index 22879c7ca..000000000
--- a/panda/drivers/windows/panda/panda.vcxproj
+++ /dev/null
@@ -1,189 +0,0 @@
-
-
-
-
- Debug
- Win32
-
-
- Release
- Win32
-
-
- Debug
- x64
-
-
- Release
- x64
-
-
-
- {5528AEFB-638D-49AF-B9D4-965154E7D531}
- Win32Proj
- panda
- 10.0.16299.0
-
-
- DynamicLibrary
- true
- v141
- Unicode
-
-
- DynamicLibrary
- false
- v141
- true
- Unicode
-
-
- DynamicLibrary
- true
- v141
- Unicode
-
-
- DynamicLibrary
- false
- v141
- true
- Unicode
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- true
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- true
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- false
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- false
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
-
- Use
- Level3
- Disabled
- WIN32;_DEBUG;_WINDOWS;_USRDLL;PANDA_EXPORTS;%(PreprocessorDefinitions)
- true
- false
-
- Windows
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);winusb.lib;setupapi.lib
-
-
-
-
- Use
- Level3
- Disabled
- _DEBUG;_WINDOWS;_USRDLL;PANDA_EXPORTS;%(PreprocessorDefinitions)
- true
-
- Windows
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);winusb.lib;setupapi.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- WIN32;NDEBUG;_WINDOWS;_USRDLL;PANDA_EXPORTS;%(PreprocessorDefinitions)
- true
-
- Windows
- true
- true
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);winusb.lib;setupapi.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- NDEBUG;_WINDOWS;_USRDLL;PANDA_EXPORTS;%(PreprocessorDefinitions)
- true
-
- Windows
- true
- true
- true
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);winusb.lib;setupapi.lib
-
-
-
-
-
-
- false
-
-
- false
-
-
- false
-
-
- false
-
-
-
-
- Create
- Create
- Create
- Create
-
-
-
-
-
-
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/panda/panda.vcxproj.filters b/panda/drivers/windows/panda/panda.vcxproj.filters
deleted file mode 100644
index afddad6e8..000000000
--- a/panda/drivers/windows/panda/panda.vcxproj.filters
+++ /dev/null
@@ -1,43 +0,0 @@
-
-
-
-
- {4FC737F1-C7A5-4376-A066-2A32D752A2FF}
- cpp;c;cc;cxx;def;odl;idl;hpj;bat;asm;asmx
-
-
- {93995380-89BD-4b04-88EB-625FBE52EBFB}
- h;hh;hpp;hxx;hm;inl;inc;xsd
-
-
- {67DA6AB6-F800-4c08-8B7A-83BB121AAD01}
- rc;ico;cur;bmp;dlg;rc2;rct;bin;rgs;gif;jpg;jpeg;jpe;resx;tiff;tif;png;wav;mfcribbon-ms
-
-
-
-
- Header Files
-
-
- Header Files
-
-
-
-
- Source Files
-
-
- Source Files
-
-
-
-
- Resource Files
-
-
-
-
- Resource Files
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/panda/resource.h b/panda/drivers/windows/panda/resource.h
deleted file mode 100644
index bf006ff4b..000000000
Binary files a/panda/drivers/windows/panda/resource.h and /dev/null differ
diff --git a/panda/drivers/windows/panda/stdafx.cpp b/panda/drivers/windows/panda/stdafx.cpp
deleted file mode 100644
index 8793e09b4..000000000
--- a/panda/drivers/windows/panda/stdafx.cpp
+++ /dev/null
@@ -1,8 +0,0 @@
-// stdafx.cpp : source file that includes just the standard includes
-// panda.pch will be the pre-compiled header
-// stdafx.obj will contain the pre-compiled type information
-
-#include "stdafx.h"
-
-// TODO: reference any additional headers you need in STDAFX.H
-// and not in this file
diff --git a/panda/drivers/windows/panda/stdafx.h b/panda/drivers/windows/panda/stdafx.h
deleted file mode 100644
index cc3d3b966..000000000
--- a/panda/drivers/windows/panda/stdafx.h
+++ /dev/null
@@ -1,19 +0,0 @@
-// stdafx.h : include file for standard system include files,
-// or project specific include files that are used frequently, but
-// are changed infrequently
-//
-
-#pragma once
-
-#include "targetver.h"
-
-#ifndef WIN32_LEAN_AND_MEAN
-#define WIN32_LEAN_AND_MEAN // Exclude rarely-used stuff from Windows headers
-#endif
-// Windows Header Files:
-#include
-
-#include
-#include
-#include
-#include
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/ECUsim_tests.cpp b/panda/drivers/windows/pandaJ2534DLL Test/ECUsim_tests.cpp
deleted file mode 100644
index 8a9161475..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/ECUsim_tests.cpp
+++ /dev/null
@@ -1,87 +0,0 @@
-#include "stdafx.h"
-#include "Loader4.h"
-#include "pandaJ2534DLL/J2534_v0404.h"
-#include "panda_shared/panda.h"
-#include "Timer.h"
-#include "ECUsim DLL\ECUsim.h"
-#include "TestHelpers.h"
-
-using namespace Microsoft::VisualStudio::CppUnitTestFramework;
-
-namespace pandaWCUsimTest
-{
-
- TEST_CLASS(ECUsimTests)
- {
- public:
-
- TEST_METHOD(ECUsim_ISO15765_SingleFrameTx_29bStandardAddrPad500k)
- {
- ECUsim sim("", 500000);
- auto p = getPanda(500);
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x02\x01\x00", 3, panda::PANDA_CAN1);
- auto msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x02\x01\x00", 3), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x06\x41\x00\xff\xff\xff\xfe\x00", 8), LINE_INFO());
- }
-
- TEST_METHOD(ECUsim_ISO15765_SingleFrameTx_29bStandardAddrPad250k)
- {
- ECUsim sim("", 250000);
- auto p = getPanda(250);
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x02\x01\x00", 3, panda::PANDA_CAN1);
- auto msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x02\x01\x00", 3), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x06""\x41\x00""\xff\xff\xff\xfe""\x00", 8), LINE_INFO());
- }
-
- TEST_METHOD(ECUsim_ISO15765_SingleFrameTx_29bExtAddrPad500k)
- {
- ECUsim sim("", 500000, TRUE);
- auto p = getPanda(500);
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x13""\x02\x01\x00", 4, panda::PANDA_CAN1);
- auto msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x13""\x02\x01\x00", 4), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x13""\x06""\x41\x00""\xff\xff\xff\xfe", 8), LINE_INFO());
- }
-
- TEST_METHOD(ECUsim_ISO15765_MultiFrameTx_29bStandardAddrPad500k)
- {
- ECUsim sim("", 500000);
- auto p = getPanda(500);
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x02\x09\x02", 3, panda::PANDA_CAN1);
- auto msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x02\x09\x02", 3), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x10\x14""\x49\x02\x01""1D4", 8), LINE_INFO());
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x30\x00\x00", 3, panda::PANDA_CAN1);
- msg_recv = panda_recv_loop(p, 3);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x30\x0\x0", 3), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x21""GP00R55", 8), LINE_INFO());
- check_panda_can_msg(msg_recv[2], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x22""B123456", 8), LINE_INFO());
- }
-
- TEST_METHOD(ECUsim_ISO15765_MultiFrameTx_29bExtAddrPad500k)
- {
- ECUsim sim("", 500000, TRUE);
- auto p = getPanda(500);
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x13""\x02\x09\x02", 4, panda::PANDA_CAN1);
- auto msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x13""\x02\x09\x02", 4), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x13""\x10\x14""\x49\x02\x01""1D", 8), LINE_INFO());
-
- p->can_send(0x18daeff1, TRUE, (const uint8_t*)"\x13""\x30\x00\x00", 4, panda::PANDA_CAN1);
- msg_recv = panda_recv_loop(p, 4);
- check_panda_can_msg(msg_recv[0], 0, 0x18daeff1, TRUE, TRUE, std::string("\x13""\x30\x0\x0", 4), LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x13""\x21""4GP00R", 8), LINE_INFO());
- check_panda_can_msg(msg_recv[2], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x13""\x22""55B123", 8), LINE_INFO());
- check_panda_can_msg(msg_recv[3], 0, 0x18daf1ef, TRUE, FALSE, std::string("\x13""\x23""456", 5), LINE_INFO());
- }
- };
-
-}
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/Loader4.cpp b/panda/drivers/windows/pandaJ2534DLL Test/Loader4.cpp
deleted file mode 100644
index f4a0b70fa..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/Loader4.cpp
+++ /dev/null
@@ -1,240 +0,0 @@
-// Loader4.cpp
-// (c) 2005 National Control Systems, Inc.
-// Portions (c) 2004 Drew Technologies, Inc.
-// Dynamic J2534 v04.04 dll loader for VB
-
-// This program is free software; you can redistribute it and/or
-// modify it under the terms of the GNU General Public License
-// as published by the Free Software Foundation; either version 2
-// of the License, or any later version.
-
-// This program is distributed in the hope that it will be useful,
-// but WITHOUT ANY WARRANTY; without even the implied warranty of
-// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-// GNU General Public License for more details.
-
-// You should have received a copy of the GNU General Public License
-// along with this program; if not, write to:
-// the Free Software Foundation, Inc.
-// 51 Franklin Street, Fifth Floor
-// Boston, MA 02110-1301, USA
-
-// National Control Systems, Inc.
-// 10737 Hamburg Rd
-// Hamburg, MI 48139
-// 810-231-2901
-
-// Drew Technologies, Inc.
-// 7012 E.M -36, Suite 3B
-// Whitmore Lake, MI 48189
-// 810-231-3171
-
-#define STRICT
-#include "stdafx.h"
-#include
-#include "Loader4.h"
-
-PTOPEN LocalOpen;
-PTCLOSE LocalClose;
-PTCONNECT LocalConnect;
-PTDISCONNECT LocalDisconnect;
-PTREADMSGS LocalReadMsgs;
-PTWRITEMSGS LocalWriteMsgs;
-PTSTARTPERIODICMSG LocalStartPeriodicMsg;
-PTSTOPPERIODICMSG LocalStopPeriodicMsg;
-PTSTARTMSGFILTER LocalStartMsgFilter;
-PTSTOPMSGFILTER LocalStopMsgFilter;
-PTSETPROGRAMMINGVOLTAGE LocalSetProgrammingVoltage;
-PTREADVERSION LocalReadVersion;
-PTGETLASTERROR LocalGetLastError;
-PTIOCTL LocalIoctl;
-
-HINSTANCE hDLL = NULL;
-//BOOL bIsCorrectVersion = FALSE;
-
-BOOL WINAPI DllMain(HINSTANCE hInstA, DWORD dwReason, LPVOID lpvReserved)
-{
- switch (dwReason) {
- case DLL_PROCESS_ATTACH:
- // The DLL is being mapped into the process's address space
-
- case DLL_THREAD_ATTACH:
- // A thread is being created
- break;
-
- case DLL_THREAD_DETACH:
- // A thread is exiting cleanly
- break;
-
- case DLL_PROCESS_DETACH:
- // The DLL is being unmapped from the process's address space
- break;
- }
-
- return TRUE;
-}
-
-
-long WINAPI LoadJ2534Dll(char *sLib)
-{
- long lFuncList = 0;
-
- if (hDLL != NULL) UnloadJ2534Dll();
- hDLL = LoadLibraryA (sLib);
- if (hDLL == NULL) return ERR_NO_DLL;
-
- LocalOpen = (PTOPEN)(GetProcAddress(hDLL, "PassThruOpen"));
- if (LocalOpen == NULL) lFuncList = lFuncList | ERR_NO_PTOPEN;
-
- LocalClose = (PTCLOSE)(GetProcAddress(hDLL, "PassThruClose"));
- if (LocalClose == NULL) lFuncList = lFuncList | ERR_NO_PTCLOSE;
-
- LocalConnect = (PTCONNECT)(GetProcAddress(hDLL,"PassThruConnect"));
- if (LocalConnect == NULL) lFuncList = lFuncList | ERR_NO_PTCONNECT;
-
- LocalDisconnect = (PTDISCONNECT)(GetProcAddress(hDLL,"PassThruDisconnect"));
- if (LocalDisconnect == NULL) lFuncList = lFuncList | ERR_NO_PTDISCONNECT;
-
- LocalReadMsgs = (PTREADMSGS)(GetProcAddress(hDLL,"PassThruReadMsgs"));
- if (LocalReadMsgs == NULL) lFuncList = lFuncList | ERR_NO_PTREADMSGS;
-
- LocalWriteMsgs = (PTWRITEMSGS)(GetProcAddress(hDLL,"PassThruWriteMsgs"));
- if (LocalWriteMsgs == NULL) lFuncList = lFuncList | ERR_NO_PTWRITEMSGS;
-
- LocalStartPeriodicMsg = (PTSTARTPERIODICMSG)(GetProcAddress(hDLL,"PassThruStartPeriodicMsg"));
- if (LocalStartPeriodicMsg == NULL) lFuncList = lFuncList | ERR_NO_PTSTARTPERIODICMSG;
-
- LocalStopPeriodicMsg = (PTSTOPPERIODICMSG)(GetProcAddress(hDLL,"PassThruStopPeriodicMsg"));
- if (LocalStopPeriodicMsg == NULL) lFuncList = lFuncList | ERR_NO_PTSTOPPERIODICMSG;
-
- LocalStartMsgFilter = (PTSTARTMSGFILTER)(GetProcAddress(hDLL,"PassThruStartMsgFilter"));
- if (LocalStartPeriodicMsg == NULL) lFuncList = lFuncList | ERR_NO_PTSTARTMSGFILTER;
-
- LocalStopMsgFilter = (PTSTOPMSGFILTER)(GetProcAddress(hDLL,"PassThruStopMsgFilter"));
- if (LocalStopMsgFilter == NULL) lFuncList = lFuncList | ERR_NO_PTSTOPMSGFILTER;
-
- LocalSetProgrammingVoltage = (PTSETPROGRAMMINGVOLTAGE)(GetProcAddress(hDLL,"PassThruSetProgrammingVoltage"));
- if (LocalSetProgrammingVoltage == NULL) lFuncList = lFuncList | ERR_NO_PTSETPROGRAMMINGVOLTAGE;
-
- LocalReadVersion = (PTREADVERSION)(GetProcAddress(hDLL,"PassThruReadVersion"));
- if (LocalReadVersion == NULL) lFuncList = lFuncList | ERR_NO_PTREADVERSION;
-
- LocalGetLastError = (PTGETLASTERROR)(GetProcAddress(hDLL,"PassThruGetLastError"));
- if (LocalGetLastError == NULL) lFuncList = lFuncList | ERR_NO_PTGETLASTERROR;
-
- LocalIoctl = (PTIOCTL)(GetProcAddress(hDLL,"PassThruIoctl"));
- if (LocalIoctl == NULL) lFuncList = lFuncList | ERR_NO_PTIOCTL;
-
- if (lFuncList == ERR_NO_FUNCTIONS) return ERR_WRONG_DLL_VER;
-
- return lFuncList;
-}
-
-long WINAPI UnloadJ2534Dll()
-{
- if (FreeLibrary(hDLL))
- {
- hDLL = NULL;
- LocalOpen = NULL;
- LocalClose = NULL;
- LocalConnect = NULL;
- LocalDisconnect = NULL;
- LocalReadMsgs = NULL;
- LocalWriteMsgs = NULL;
- LocalStartPeriodicMsg = NULL;
- LocalStopPeriodicMsg = NULL;
- LocalStartMsgFilter = NULL;
- LocalStopMsgFilter = NULL;
- LocalSetProgrammingVoltage = NULL;
- LocalReadVersion = NULL;
- LocalGetLastError = NULL;
- LocalIoctl = NULL;
- return 0;
- }
- return ERR_NO_DLL;
-}
-
-long WINAPI PassThruOpen(void *pName, unsigned long *pDeviceID)
-{
- if (LocalOpen == NULL) return ERR_FUNC_MISSING;
- return LocalOpen(pName, pDeviceID);
-}
-
-long WINAPI PassThruClose(unsigned long DeviceID)
-{
- if (LocalOpen == NULL) return ERR_FUNC_MISSING;
- return LocalClose(DeviceID);
-}
-
-long WINAPI PassThruConnect(unsigned long DeviceID, unsigned long ProtocolID, unsigned long Flags, unsigned long Baudrate, unsigned long *pChannelID)
-{
- if (LocalConnect == NULL) return ERR_FUNC_MISSING;
- return LocalConnect(DeviceID, ProtocolID, Flags, Baudrate, pChannelID);
-}
-
-long WINAPI PassThruDisconnect(unsigned long ChannelID)
-{
- if (LocalDisconnect == NULL) return ERR_FUNC_MISSING;
- return LocalDisconnect(ChannelID);
-}
-
-long WINAPI PassThruReadMsgs(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout)
-{
- if (LocalReadMsgs == NULL) return ERR_FUNC_MISSING;
- return LocalReadMsgs(ChannelID, pMsg, pNumMsgs, Timeout);
-}
-
-long WINAPI PassThruWriteMsgs(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout)
-{
- if (LocalWriteMsgs == NULL) return ERR_FUNC_MISSING;
- return LocalWriteMsgs(ChannelID, pMsg, pNumMsgs, Timeout);
-}
-
-long WINAPI PassThruStartPeriodicMsg(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pMsgID, unsigned long TimeInterval)
-{
- if (LocalStartPeriodicMsg == NULL) return ERR_FUNC_MISSING;
- return LocalStartPeriodicMsg(ChannelID, pMsg, pMsgID, TimeInterval);
-}
-
-long WINAPI PassThruStopPeriodicMsg(unsigned long ChannelID, unsigned long MsgID)
-{
- if (LocalStopPeriodicMsg == NULL) return ERR_FUNC_MISSING;
- return LocalStopPeriodicMsg(ChannelID, MsgID);
-}
-
-long WINAPI PassThruStartMsgFilter(unsigned long ChannelID, unsigned long FilterType,
- PASSTHRU_MSG *pMaskMsg, PASSTHRU_MSG *pPatternMsg, PASSTHRU_MSG *pFlowControlMsg, unsigned long *pFilterID)
-{
- if (LocalStartMsgFilter == NULL) return ERR_FUNC_MISSING;
- return LocalStartMsgFilter(ChannelID, FilterType, pMaskMsg, pPatternMsg, pFlowControlMsg, pFilterID);
-}
-
-long WINAPI PassThruStopMsgFilter(unsigned long ChannelID, unsigned long FilterID)
-{
- if (LocalStopMsgFilter == NULL) return ERR_FUNC_MISSING;
- return LocalStopMsgFilter(ChannelID, FilterID);
-}
-
-long WINAPI PassThruSetProgrammingVoltage(unsigned long DeviceID, unsigned long PinNumber, unsigned long Voltage)
-{
- if (LocalSetProgrammingVoltage == NULL) return ERR_FUNC_MISSING;
- return LocalSetProgrammingVoltage(DeviceID, PinNumber, Voltage);
-}
-
-long WINAPI PassThruReadVersion(unsigned long DeviceID, char *pFirmwareVersion, char *pDllVersion, char *pApiVersion)
-{
- if (LocalReadVersion == NULL) return ERR_FUNC_MISSING;
- return LocalReadVersion(DeviceID, pFirmwareVersion, pDllVersion, pApiVersion);
-}
-
-long WINAPI PassThruGetLastError(char *pErrorDescription)
-{
- if (LocalGetLastError == NULL) return ERR_FUNC_MISSING;
- return LocalGetLastError(pErrorDescription);
-}
-
-long WINAPI PassThruIoctl(unsigned long ChannelID, unsigned long IoctlID, void *pInput, void *pOutput)
-{
- if (LocalIoctl == NULL) return ERR_FUNC_MISSING;
- return LocalIoctl(ChannelID, IoctlID, pInput, pOutput);
-}
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/Loader4.h b/panda/drivers/windows/pandaJ2534DLL Test/Loader4.h
deleted file mode 100644
index 971014414..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/Loader4.h
+++ /dev/null
@@ -1,55 +0,0 @@
-// Loader4.h
-// (c) 2005 National Control Systems, Inc.
-// Portions (c) 2004 Drew Technologies, Inc.
-
-// This program is free software; you can redistribute it and/or
-// modify it under the terms of the GNU General Public License
-// as published by the Free Software Foundation; either version 2
-// of the License, or any later version.
-
-// This program is distributed in the hope that it will be useful,
-// but WITHOUT ANY WARRANTY; without even the implied warranty of
-// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-// GNU General Public License for more details.
-
-// You should have received a copy of the GNU General Public License
-// along with this program; if not, write to:
-// the Free Software Foundation, Inc.
-// 51 Franklin Street, Fifth Floor
-// Boston, MA 02110-1301, USA
-
-// National Control Systems, Inc.
-// 10737 Hamburg Rd
-// Hamburg, MI 48139
-// 810-231-2901
-
-// Drew Technologies, Inc.
-// 7012 E.M -36, Suite 3B
-// Whitmore Lake, MI 48189
-// 810-231-3171
-
-#include "pandaJ2534DLL/J2534_v0404.h"
-
-//Other Functions
-long WINAPI LoadJ2534Dll(char *);
-long WINAPI UnloadJ2534Dll();
-
-// NCS Returns of any functions not found
-#define ERR_NO_PTOPEN 0x0001
-#define ERR_NO_PTCLOSE 0x0002
-#define ERR_NO_PTCONNECT 0x0004
-#define ERR_NO_PTDISCONNECT 0x0008
-#define ERR_NO_PTREADMSGS 0x0010
-#define ERR_NO_PTWRITEMSGS 0x0020
-#define ERR_NO_PTSTARTPERIODICMSG 0x0040
-#define ERR_NO_PTSTOPPERIODICMSG 0x0080
-#define ERR_NO_PTSTARTMSGFILTER 0x0100
-#define ERR_NO_PTSTOPMSGFILTER 0x0200
-#define ERR_NO_PTSETPROGRAMMINGVOLTAGE 0x0400
-#define ERR_NO_PTREADVERSION 0x0800
-#define ERR_NO_PTGETLASTERROR 0x1000
-#define ERR_NO_PTIOCTL 0x2000
-#define ERR_NO_FUNCTIONS 0x3fff
-#define ERR_NO_DLL -1
-#define ERR_WRONG_DLL_VER -2
-#define ERR_FUNC_MISSING -3
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/TestHelpers.cpp b/panda/drivers/windows/pandaJ2534DLL Test/TestHelpers.cpp
deleted file mode 100644
index 1281eb9d6..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/TestHelpers.cpp
+++ /dev/null
@@ -1,254 +0,0 @@
-#include "stdafx.h"
-#include "TestHelpers.h"
-#include "Loader4.h"
-#include "pandaJ2534DLL/J2534_v0404.h"
-#include "panda_shared/panda.h"
-#include "Timer.h"
-
-using namespace Microsoft::VisualStudio::CppUnitTestFramework;
-
-void write_ioctl(unsigned int chanid, unsigned int param, unsigned int val, const __LineInfo* pLineInfo) {
- SCONFIG config = { param, val };
- SCONFIG_LIST inconfig = { 1, &config };
-
- Assert::AreEqual(STATUS_NOERROR, PassThruIoctl(chanid, SET_CONFIG, &inconfig, NULL), _T("Failed to set IOCTL."), pLineInfo);
-}
-
-std::vector panda_recv_loop_loose(std::unique_ptr& p, unsigned int min_num, unsigned long timeout_ms) {
- std::vector ret_messages;
- Timer t = Timer();
-
- while (t.getTimePassed() < timeout_ms) {
- Sleep(10);
- std::vectormsg_recv = p->can_recv();
- if (msg_recv.size() > 0) {
- ret_messages.insert(std::end(ret_messages), std::begin(msg_recv), std::end(msg_recv));
- }
- }
-
- Assert::IsTrue(min_num <= ret_messages.size(), _T("Received too few messages."));
- return ret_messages;
-}
-
-std::vector panda_recv_loop(std::unique_ptr& p, unsigned int num_expected, unsigned long timeout_ms) {
- std::vector ret_messages;
- Timer t = Timer();
-
- while (t.getTimePassed() < timeout_ms) {
- Sleep(10);
- std::vectormsg_recv = p->can_recv();
- if (msg_recv.size() > 0) {
- ret_messages.insert(std::end(ret_messages), std::begin(msg_recv), std::end(msg_recv));
- }
- if (ret_messages.size() >= num_expected) break;
- }
-
- std::ostringstream stringStream;
-
- stringStream << "j2534_recv_loop Broke at " << t.getTimePassed() << " ms size is " << ret_messages.size() << std::endl;
-
- if (num_expected != ret_messages.size()) {
- stringStream << "Incorrect number of messages received. Displaying the messages:" << std::endl;
- for (auto msg : ret_messages) {
- stringStream << " TS: " << msg.recv_time << "; Dat: ";
- for (int i = 0; i < msg.len; i++) stringStream << std::hex << std::setw(2) << std::setfill('0') << int(msg.dat[i] & 0xFF) << " ";
- stringStream << std::endl;
- }
- }
-
- Logger::WriteMessage(stringStream.str().c_str());
-
- Assert::AreEqual(num_expected, ret_messages.size(), _T("Received wrong number of messages."));
- return ret_messages;
-}
-
-void check_panda_can_msg(panda::PANDA_CAN_MSG& msgin, uint8_t bus, unsigned long addr, bool addr_29b,
- bool is_receipt, std::string dat, const __LineInfo* pLineInfo) {
- Assert::AreEqual(bus, msgin.bus, _T("Wrong msg bus"), pLineInfo);
- Assert::AreEqual(addr, msgin.addr, _T("Wrong msg addr"), pLineInfo);
- Assert::AreEqual(addr_29b, msgin.addr_29b, _T("Wrong msg 29b flag"), pLineInfo);
- Assert::AreEqual(is_receipt, msgin.is_receipt, _T("Wrong msg receipt flag"), pLineInfo);
-
- std::ostringstream logmsg;
- logmsg << "Expected Hex (";
- for (int i = 0; i < dat.size(); i++) logmsg << std::hex << std::setw(2) << std::setfill('0') << int(dat[i] & 0xFF) << " ";
- logmsg << "); Actual Hex (";
- for (int i = 0; i < msgin.len; i++) logmsg << std::hex << std::setw(2) << std::setfill('0') << int(((char*)msgin.dat)[i] & 0xFF) << " ";
- logmsg << ")";
- Logger::WriteMessage(logmsg.str().c_str());
-
- Assert::AreEqual(dat.size(), msgin.len, _T("Wrong msg len"), pLineInfo);
- Assert::AreEqual(dat, std::string((char*)msgin.dat, msgin.len), _T("Wrong msg payload"), pLineInfo);
-}
-
-unsigned long J2534_start_periodic_msg_checked(unsigned long chanid, unsigned long ProtocolID, unsigned long TxFlags, unsigned long DataSize,
- unsigned long ExtraDataIndex, const char * Data, unsigned long TimeInterval, const __LineInfo * pLineInfo) {
- PASSTHRU_MSG msg = { ProtocolID, 0, TxFlags, 0, DataSize, ExtraDataIndex };
- memcpy_s(msg.Data, 4128, Data, DataSize);
- unsigned long msgID;
- Assert::AreEqual(STATUS_NOERROR, J2534_start_periodic_msg(chanid, ProtocolID, TxFlags, DataSize,
- ExtraDataIndex, Data, TimeInterval, &msgID, pLineInfo), _T("Failed to start Periodic Message."), pLineInfo);
- return msgID;
-}
-
-unsigned long J2534_start_periodic_msg(unsigned long chanid, unsigned long ProtocolID, unsigned long TxFlags, unsigned long DataSize,
- unsigned long ExtraDataIndex, const char * Data, unsigned long TimeInterval, unsigned long* msgID, const __LineInfo * pLineInfo) {
- PASSTHRU_MSG msg = { ProtocolID, 0, TxFlags, 0, DataSize, ExtraDataIndex };
- memcpy_s(msg.Data, 4128, Data, DataSize);
- return PassThruStartPeriodicMsg(chanid, &msg, msgID, TimeInterval);
-}
-
-void J2534_send_msg_checked(unsigned long chanid, unsigned long ProtocolID, unsigned long RxStatus, unsigned long TxFlags,
- unsigned long Timestamp, unsigned long DataSize, unsigned long ExtraDataIndex, const char* Data, const __LineInfo* pLineInfo) {
-
- PASSTHRU_MSG msg = { ProtocolID, RxStatus, TxFlags, Timestamp, DataSize, ExtraDataIndex };
- memcpy_s(msg.Data, 4128, Data, DataSize);
- unsigned long msgcount = 1;
- Assert::AreEqual(STATUS_NOERROR, PassThruWriteMsgs(chanid, &msg, &msgcount, 0), _T("Failed to write message."), pLineInfo);
- Assert::AreEqual(1, msgcount, _T("Wrong message count after tx."), pLineInfo);
-}
-
-long J2534_send_msg(unsigned long chanid, unsigned long ProtocolID, unsigned long RxStatus, unsigned long TxFlags,
- unsigned long Timestamp, unsigned long DataSize, unsigned long ExtraDataIndex, const char* Data) {
-
- PASSTHRU_MSG msg = { ProtocolID, RxStatus, TxFlags, Timestamp, DataSize, ExtraDataIndex };
- memcpy_s(msg.Data, 4128, Data, DataSize);
- unsigned long msgcount = 1;
- return PassThruWriteMsgs(chanid, &msg, &msgcount, 0);
-}
-
-//Allow more messages to come in than the min.
-std::vector j2534_recv_loop_loose(unsigned int chanid, unsigned int min_num, unsigned long timeout_ms) {
- std::vector ret_messages;
- PASSTHRU_MSG recvbuff[4] = {};
- Timer t = Timer();
-
- while (t.getTimePassed() < timeout_ms) {
- unsigned long msgcount = 4;
- unsigned int res = PassThruReadMsgs(chanid, recvbuff, &msgcount, 0);
- if (res == ERR_BUFFER_EMPTY) continue;
- Assert::IsFalse(msgcount > 4, _T("PassThruReadMsgs returned more data than the buffer could hold."));
- Assert::AreEqual(STATUS_NOERROR, res, _T("Failed to read message."));
- if (msgcount > 0) {
- for (unsigned int i = 0; i < msgcount; i++) {
- ret_messages.push_back(recvbuff[i]);
- }
- }
- }
-
- Assert::IsTrue(min_num <= ret_messages.size(), _T("Received too few messages."));
- return ret_messages;
-}
-
-std::vector j2534_recv_loop(unsigned int chanid, unsigned int num_expected, unsigned long timeout_ms) {
- std::vector ret_messages;
- PASSTHRU_MSG recvbuff[4] = {};
- Timer t = Timer();
-
- while (t.getTimePassed() < timeout_ms) {
- unsigned long msgcount = 4;
- unsigned int res = PassThruReadMsgs(chanid, recvbuff, &msgcount, 0);
- if (res == ERR_BUFFER_EMPTY) continue;
- Assert::IsFalse(msgcount > 4, _T("PassThruReadMsgs returned more data than the buffer could hold."));
- Assert::AreEqual(STATUS_NOERROR, res, _T("Failed to read message."));
- if (msgcount > 0) {
- for (unsigned int i = 0; i < msgcount; i++) {
- ret_messages.push_back(recvbuff[i]);
- }
- }
- if (ret_messages.size() >= num_expected) break;
- }
-
- std::ostringstream stringStream;
- stringStream << "j2534_recv_loop Broke at " << t.getTimePassed() << " ms size is " << ret_messages.size() << std::endl;
-
- if (num_expected != ret_messages.size()) {
- stringStream << "Incorrect number of messages received. Displaying the messages:" << std::endl;
- for (auto msg : ret_messages) {
- stringStream << " TS: " << msg.Timestamp << "; Dat: ";
- for (int i = 0; i < msg.DataSize; i++) stringStream << std::hex << std::setw(2) << std::setfill('0') << int(msg.Data[i] & 0xFF) << " ";
- stringStream << std::endl;
- }
- }
-
- Logger::WriteMessage(stringStream.str().c_str());
-
- Assert::AreEqual(num_expected, ret_messages.size(), _T("Received wrong number of messages."));
- return ret_messages;
-}
-
-void check_J2534_can_msg(PASSTHRU_MSG& msgin, unsigned long ProtocolID, unsigned long RxStatus, unsigned long TxFlags,
- unsigned long DataSize, unsigned long ExtraDataIndex, const char* Data, const __LineInfo* pLineInfo) {
- Assert::AreEqual(DataSize, msgin.DataSize, _T("Wrong msg len"), pLineInfo);
-
- std::ostringstream logmsg;
- logmsg << "Expected Hex (";
- for (int i = 0; i < DataSize; i++) logmsg << std::hex << std::setw(2) << std::setfill('0') << int(Data[i] & 0xFF) << " ";
- logmsg << "); Actual Hex (";
- for (int i = 0; i < msgin.DataSize; i++) logmsg << std::hex << std::setw(2) << std::setfill('0') << int(((char*)msgin.Data)[i] & 0xFF) << " ";
- logmsg << ")";
- Logger::WriteMessage(logmsg.str().c_str());
- Assert::AreEqual(std::string(Data, DataSize), std::string((char*)msgin.Data, msgin.DataSize), _T("Wrong msg payload"), pLineInfo);
-
- Assert::AreEqual(ProtocolID, msgin.ProtocolID, _T("Wrong msg protocol"), pLineInfo);
- Assert::AreEqual(RxStatus, msgin.RxStatus, _T("Wrong msg receipt rxstatus"), pLineInfo);
- Assert::AreEqual(TxFlags, msgin.TxFlags, _T("Wrong msg receipt txflag"), pLineInfo);
- Assert::AreEqual(ExtraDataIndex, msgin.ExtraDataIndex, _T("Wrong msg ExtraDataIndex"), pLineInfo);
-}
-
-unsigned long J2534_set_PASS_filter(unsigned long chanid, unsigned long ProtocolID, unsigned long tx,
- unsigned long len, char* mask, char* pattern, const __LineInfo* pLineInfo) {
- unsigned long filterid;
- PASSTHRU_MSG mask_msg = { ProtocolID, 0, tx, 0, len, 0, 0 };
- PASSTHRU_MSG pattern_msg = { ProtocolID, 0, tx, 0, len, 0, 0 };
- memcpy(mask_msg.Data, mask, len);
- memcpy(pattern_msg.Data, pattern, len);
- Assert::AreEqual(STATUS_NOERROR, PassThruStartMsgFilter(chanid, PASS_FILTER, &mask_msg, &pattern_msg, NULL, &filterid),
- _T("Failed to create filter."), pLineInfo);
- return filterid;
-}
-
-unsigned long J2534_set_BLOCK_filter(unsigned long chanid, unsigned long ProtocolID, unsigned long tx,
- unsigned long len, char* mask, char* pattern, const __LineInfo* pLineInfo) {
- unsigned long filterid;
- PASSTHRU_MSG mask_msg = { ProtocolID, 0, tx, 0, len, 0, 0 };
- PASSTHRU_MSG pattern_msg = { ProtocolID, 0, tx, 0, len, 0, 0 };
- memcpy(mask_msg.Data, mask, len);
- memcpy(pattern_msg.Data, pattern, len);
- Assert::AreEqual(STATUS_NOERROR, PassThruStartMsgFilter(chanid, BLOCK_FILTER, &mask_msg, &pattern_msg, NULL, &filterid),
- _T("Failed to create filter."), pLineInfo);
- return filterid;
-}
-
-unsigned long J2534_set_flowctrl_filter(unsigned long chanid, unsigned long tx,
- unsigned long len, char* mask, char* pattern, char* flow, const __LineInfo* pLineInfo) {
- unsigned long filterid;
- PASSTHRU_MSG mask_msg = { ISO15765, 0, tx, 0, len, 0, 0 };
- PASSTHRU_MSG pattern_msg = { ISO15765, 0, tx, 0, len, 0, 0 };
- PASSTHRU_MSG flow_msg = { ISO15765, 0, tx, 0, len, 0, 0 };
- memcpy(mask_msg.Data, mask, len);
- memcpy(pattern_msg.Data, pattern, len);
- memcpy(flow_msg.Data, flow, len);
- Assert::AreEqual(STATUS_NOERROR, PassThruStartMsgFilter(chanid, FLOW_CONTROL_FILTER, &mask_msg, &pattern_msg, &flow_msg, &filterid),
- _T("Failed to create filter."), pLineInfo);
- return filterid;
-}
-
-std::unique_ptr getPanda(unsigned long kbaud, BOOL loopback) {
- auto p = panda::Panda::openPanda("");
- Assert::IsTrue(p != nullptr, _T("Could not open raw panda device to test communication."));
- p->set_can_speed_kbps(panda::PANDA_CAN1, kbaud);
- p->set_safety_mode(panda::SAFETY_ALLOUTPUT);
- p->set_can_loopback(loopback);
- p->can_clear(panda::PANDA_CAN_RX);
- return p;
-}
-
-std::vector checked_panda_send(std::unique_ptr& p, uint32_t addr, bool is_29b,
- char* msg, uint8_t len, unsigned int num_expected, const __LineInfo* pLineInfo, unsigned long timeout_ms) {
- Assert::IsTrue(p->can_send(addr, is_29b, (const uint8_t*)msg, len, panda::PANDA_CAN1), _T("Panda send says it failed."), pLineInfo);
- auto panda_msg_recv = panda_recv_loop(p, 1 + num_expected, timeout_ms);
- check_panda_can_msg(panda_msg_recv[0], 0, addr, is_29b, TRUE, std::string(msg, len), pLineInfo);
- panda_msg_recv.erase(panda_msg_recv.begin());
- return panda_msg_recv;
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/TestHelpers.h b/panda/drivers/windows/pandaJ2534DLL Test/TestHelpers.h
deleted file mode 100644
index 9df59d7b5..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/TestHelpers.h
+++ /dev/null
@@ -1,48 +0,0 @@
-#pragma once
-#include "stdafx.h"
-#include "pandaJ2534DLL/J2534_v0404.h"
-#include "panda_shared/panda.h"
-
-using namespace Microsoft::VisualStudio::CppUnitTestFramework;
-
-extern void write_ioctl(unsigned int chanid, unsigned int param, unsigned int val, const __LineInfo* pLineInfo = NULL);
-
-extern std::vector panda_recv_loop_loose(std::unique_ptr& p, unsigned int min_num, unsigned long timeout_ms = 100);
-
-extern std::vector panda_recv_loop(std::unique_ptr& p, unsigned int num_expected, unsigned long timeout_ms = 100);
-
-extern void check_panda_can_msg(panda::PANDA_CAN_MSG& msgin, uint8_t bus, unsigned long addr, bool addr_29b,
- bool is_receipt, std::string dat, const __LineInfo* pLineInfo = NULL);
-
-extern unsigned long J2534_start_periodic_msg_checked(unsigned long chanid, unsigned long ProtocolID, unsigned long TxFlags, unsigned long DataSize,
- unsigned long ExtraDataIndex, const char * Data, unsigned long TimeInterval, const __LineInfo * pLineInfo);
-
-extern unsigned long J2534_start_periodic_msg(unsigned long chanid, unsigned long ProtocolID, unsigned long TxFlags, unsigned long DataSize,
- unsigned long ExtraDataIndex, const char* Data, unsigned long TimeInterval, unsigned long* msgID, const __LineInfo* pLineInfo = NULL);
-
-extern void J2534_send_msg_checked(unsigned long chanid, unsigned long ProtocolID, unsigned long RxStatus, unsigned long TxFlags,
- unsigned long Timestamp, unsigned long DataSize, unsigned long ExtraDataIndex, const char* Data, const __LineInfo* pLineInfo = NULL);
-
-extern long J2534_send_msg(unsigned long chanid, unsigned long ProtocolID, unsigned long RxStatus, unsigned long TxFlags,
- unsigned long Timestamp, unsigned long DataSize, unsigned long ExtraDataIndex, const char* Data);
-
-extern std::vector j2534_recv_loop_loose(unsigned int chanid, unsigned int min_num, unsigned long timeout_ms = 100);
-
-extern std::vector j2534_recv_loop(unsigned int chanid, unsigned int num_expected, unsigned long timeout_ms = 100);
-
-extern void check_J2534_can_msg(PASSTHRU_MSG& msgin, unsigned long ProtocolID, unsigned long RxStatus, unsigned long TxFlags,
- unsigned long DataSize, unsigned long ExtraDataIndex, const char* Data, const __LineInfo* pLineInfo = NULL);
-
-extern unsigned long J2534_set_PASS_filter(unsigned long chanid, unsigned long ProtocolID, unsigned long tx,
- unsigned long len, char* mask, char* pattern, const __LineInfo* pLineInfo = NULL);
-
-extern unsigned long J2534_set_BLOCK_filter(unsigned long chanid, unsigned long ProtocolID, unsigned long tx,
- unsigned long len, char* mask, char* pattern, const __LineInfo* pLineInfo = NULL);
-
-extern unsigned long J2534_set_flowctrl_filter(unsigned long chanid, unsigned long tx,
- unsigned long len, char* mask, char* pattern, char* flow, const __LineInfo* pLineInfo = NULL);
-
-extern std::unique_ptr getPanda(unsigned long kbaud = 500, BOOL loopback = FALSE);
-
-extern std::vector checked_panda_send(std::unique_ptr& p, uint32_t addr, bool is_29b,
- char* msg, uint8_t len, unsigned int num_expected=0, const __LineInfo* pLineInfo = NULL, unsigned long timeout_ms = 100);
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/Timer.cpp b/panda/drivers/windows/pandaJ2534DLL Test/Timer.cpp
deleted file mode 100644
index 33d029e84..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/Timer.cpp
+++ /dev/null
@@ -1,21 +0,0 @@
-#include "stdafx.h"
-#include "Timer.h"
-
-
-Timer::Timer()
-{
- reset();
-}
-
-// gets the time elapsed from construction.
-unsigned long long /*milliseconds*/ Timer::getTimePassed(){
- // get the new time
- auto end = std::chrono::time_point_cast(clock::now());
-
- // return the difference of the times
- return (end - start).count();
-}
-
-void Timer::reset() {
- start = std::chrono::time_point_cast(clock::now());
-}
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/Timer.h b/panda/drivers/windows/pandaJ2534DLL Test/Timer.h
deleted file mode 100644
index cbf5579a5..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/Timer.h
+++ /dev/null
@@ -1,20 +0,0 @@
-#pragma once
-#include
-
-//Copied from https://stackoverflow.com/a/31488113
-
-class Timer
-{
- using clock = std::chrono::steady_clock;
- using time_point_type = std::chrono::time_point < clock, std::chrono::milliseconds >;
-public:
- Timer();
-
- // gets the time elapsed from construction.
- unsigned long long /*milliseconds*/ getTimePassed();
-
- void reset();
-
-private:
- time_point_type start;
-};
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/j2534_tests.cpp b/panda/drivers/windows/pandaJ2534DLL Test/j2534_tests.cpp
deleted file mode 100644
index 674569acc..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/j2534_tests.cpp
+++ /dev/null
@@ -1,1602 +0,0 @@
-#include "stdafx.h"
-#include "Loader4.h"
-#include "pandaJ2534DLL/J2534_v0404.h"
-#include "panda_shared/panda.h"
-#include "Timer.h"
-#include "ECUsim DLL\ECUsim.h"
-#include "TestHelpers.h"
-
-using namespace Microsoft::VisualStudio::CppUnitTestFramework;
-
-namespace pandaJ2534DLLTest
-{
- TEST_CLASS(J2534DLLInitialization)
- {
- public:
-
- TEST_CLASS_CLEANUP(deinit) {
- UnloadJ2534Dll();
- }
-
- TEST_METHOD(J2534_Driver_Init)
- {
- long err = LoadJ2534Dll("pandaJ2534_0404_32.dll");
- Assert::IsTrue(err == 0, _T("Library failed to load properly. Check the export names and library location."));
- }
-
- };
-
- TEST_CLASS(J2534DeviceInitialization)
- {
- public:
-
- TEST_METHOD_INITIALIZE(init) {
- LoadJ2534Dll("pandaJ2534_0404_32.dll");
- }
-
- TEST_METHOD_CLEANUP(deinit) {
- if (didopen) {
- PassThruClose(devid);
- didopen = FALSE;
- }
- UnloadJ2534Dll();
- }
-
- TEST_METHOD(J2534_Device_OpenDevice__Empty)
- {
- Assert::AreEqual(STATUS_NOERROR, open_dev(""), _T("Failed to open device."), LINE_INFO());
- }
-
- TEST_METHOD(J2534_Device_OpenDevice__J2534_2)
- {
- Assert::AreEqual(STATUS_NOERROR, open_dev("J2534-2:"), _T("Failed to open device."), LINE_INFO());
- }
-
- TEST_METHOD(J2534_Device_OpenDevice__SN)
- {
- auto pandas_available = panda::Panda::listAvailablePandas();
- Assert::IsTrue(pandas_available.size() > 0, _T("No pandas detected."));
-
- Assert::AreEqual(STATUS_NOERROR, open_dev(pandas_available[0].c_str()), _T("Failed to open device."), LINE_INFO());
-
- auto pandas_available_2 = panda::Panda::listAvailablePandas();
- for (auto panda_sn : pandas_available_2)
- Assert::AreNotEqual(panda_sn, pandas_available[0]);
- }
-
- TEST_METHOD(J2534_Device_CloseDevice)
- {
- Assert::AreEqual(STATUS_NOERROR, open_dev(""), _T("Failed to open device."), LINE_INFO());
- Assert::AreEqual(STATUS_NOERROR, close_dev(devid), _T("Failed to close device."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_DEVICE_ID, PassThruClose(devid), _T("The 2nd close should have failed with ERR_INVALID_DEVICE_ID."), LINE_INFO());
- }
-
- TEST_METHOD(J2534_Device_ConnectDisconnect)
- {
- unsigned long chanid;
- Assert::AreEqual(STATUS_NOERROR, open_dev(""), _T("Failed to open device."), LINE_INFO());
- Assert::AreEqual(STATUS_NOERROR, PassThruConnect(devid, CAN, 0, 500000, &chanid), _T("Failed to open channel."), LINE_INFO());
-
- Assert::AreEqual(STATUS_NOERROR, PassThruDisconnect(chanid), _T("Failed to close channel."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_CHANNEL_ID, PassThruDisconnect(chanid), _T("The 2nd disconnect should have failed with ERR_INVALID_CHANNEL_ID."), LINE_INFO());
- }
-
- TEST_METHOD(J2534_Device_ConnectInvalidProtocol)
- {
- unsigned long chanid;
- Assert::AreEqual(STATUS_NOERROR, open_dev(""), _T("Failed to open device."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_PROTOCOL_ID, PassThruConnect(devid, 999, 0, 500000, &chanid),
- _T("Did not report ERR_INVALID_PROTOCOL_ID."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_CHANNEL_ID, PassThruDisconnect(chanid), _T("The channel should not have been created."), LINE_INFO());
- }
-
- bool didopen = FALSE;
- unsigned long devid;
-
- unsigned long open_dev(const char* name, long assert_err = STATUS_NOERROR, TCHAR* failmsg = _T("Failed to open device.")) {
- unsigned int res = PassThruOpen((void*)name, &devid);
- if (res == STATUS_NOERROR) didopen = TRUE;
- return res;
- }
-
- unsigned long close_dev(unsigned long devid) {
- unsigned long res = PassThruClose(devid);
- if (res == STATUS_NOERROR) didopen = FALSE;
- return res;
- }
-
- };
-
- TEST_CLASS(J2534DeviceCAN)
- {
- public:
-
- TEST_METHOD_INITIALIZE(init) {
- LoadJ2534Dll("pandaJ2534_0404_32.dll");
- }
-
- TEST_METHOD_CLEANUP(deinit) {
- if (didopen) {
- PassThruClose(devid);
- didopen = FALSE;
- }
- UnloadJ2534Dll();
- }
-
- //Test that the BAUD rate of a CAN connection can be changed.
- TEST_METHOD(J2534_CAN_SetBaud)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO()); // ENABLE J2534 ECHO/LOOPBACK
- auto p = getPanda(250);
-
- J2534_send_msg_checked(chanid, CAN, 0, 0, 0, 4 + 2, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
- j2534_recv_loop(chanid, 0);
- panda_recv_loop(p, 0);
-
- write_ioctl(chanid, DATA_RATE, 250000, LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, TX_MSG_TYPE, 0, 4 + 2, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_11b_Tx)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, CAN, 0, 0, 0, 6, 6, "\x0\x0\x3\xAB""HI", LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
-
- j2534_recv_loop(chanid, 0, 50); // Check no message is returned (since loopback is off)
- }
-
- TEST_METHOD(J2534_CAN_29b_Tx)
- {
- auto chanid = J2534_open_and_connect("", CAN, CAN_29BIT_ID, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- Assert::AreEqual(ERR_INVALID_MSG, J2534_send_msg(chanid, CAN, 0, 0, 0, 6, 6, "\x0\x0\x3\xAB""HI"), _T("11b address should fail to tx."), LINE_INFO());
- J2534_send_msg_checked(chanid, CAN, 0, CAN_29BIT_ID, 0, 6, 6, "\x0\x0\x3\xAB""YO", LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, TRUE, FALSE, "YO", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_11b29b_Tx)
- {
- auto chanid = J2534_open_and_connect("", CAN, CAN_ID_BOTH, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, CAN, 0, 0, 0, 6, 6, "\x0\x0\x3\xAB""HI", LINE_INFO());
- J2534_send_msg_checked(chanid, CAN, 0, CAN_29BIT_ID, 0, 6, 6, "\x0\x0\x3\xAB""YO", LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x3AB, TRUE, FALSE, "YO", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_TxEcho)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, CAN, 0, 0, 0, 9, 9, "\x0\x0\x3\xAB""HIDOG", LINE_INFO());
-
- auto msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HIDOG", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 0);
-
- /////////////////////////////////
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO()); // ENABLE J2534 ECHO/LOOPBACK
-
- J2534_send_msg_checked(chanid, CAN, 0, 0, 0, 7, 7, "\x0\x0\x3\xAB""SUP", LINE_INFO());
-
- msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "SUP", LINE_INFO());
-
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, TX_MSG_TYPE, 0, 3 + 4, 0, "\x0\x0\x3\xAB""SUP", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_RxAndPassAllFilters)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- J2534_set_PASS_filter(chanid, CAN, 0, 4, "\x0\x0\x0\x0", "\x0\x0\x0\x0", LINE_INFO());
- auto p = getPanda(500);
-
- p->can_send(0x1FA, FALSE, (const uint8_t*)"ABCDE", 5, panda::PANDA_CAN1);
- p->can_send(0x2AC, FALSE, (const uint8_t*)"HIJKL", 5, panda::PANDA_CAN1);
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x1\xFA""ABCDE", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x2\xAC""HIJKL", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_RxAndLimitedPassFilter)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- J2534_set_PASS_filter(chanid, CAN, 0, 4, "\xFF\xFF\xFF\xFF", "\x0\x0\x02\xAC", LINE_INFO());
- auto p = getPanda(500);
-
- p->can_send(0x1FA, FALSE, (const uint8_t*)"ABCDE", 5, panda::PANDA_CAN1);
- p->can_send(0x2AC, FALSE, (const uint8_t*)"HIJKL", 5, panda::PANDA_CAN1);
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x2\xAC""HIJKL", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_RxAndPassBlockFilter)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- J2534_set_PASS_filter(chanid, CAN, 0, 4, "\x0\x0\x0\x0", "\x0\x0\x0\x0", LINE_INFO());
- J2534_set_BLOCK_filter(chanid, CAN, 0, 4, "\xFF\xFF\xFF\xFF", "\x0\x0\x02\xAC", LINE_INFO());
- auto p = getPanda(500);
-
- p->can_send(0x1FA, FALSE, (const uint8_t*)"ABCDE", 5, panda::PANDA_CAN1);
- p->can_send(0x2AC, FALSE, (const uint8_t*)"HIJKL", 5, panda::PANDA_CAN1);
- p->can_send(0x3FA, FALSE, (const uint8_t*)"MNOPQ", 5, panda::PANDA_CAN1);
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2, 1000);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x1\xFA""ABCDE", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x3\xFA""MNOPQ", LINE_INFO());
- }
-
- //Check that the order of the pass and block filter do not matter
- TEST_METHOD(J2534_CAN_RxAndFilterBlockPass)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- J2534_set_BLOCK_filter(chanid, CAN, 0, 4, "\xFF\xFF\xFF\xFF", "\x0\x0\x02\xAC", LINE_INFO());
- J2534_set_PASS_filter(chanid, CAN, 0, 4, "\x0\x0\x0\x0", "\x0\x0\x0\x0", LINE_INFO());
- auto p = getPanda(500);
-
- p->can_send(0x1FA, FALSE, (const uint8_t*)"ABCDE", 5, panda::PANDA_CAN1);
- p->can_send(0x2AC, FALSE, (const uint8_t*)"HIJKL", 5, panda::PANDA_CAN1); // Should not pass filter
- p->can_send(0x3FA, FALSE, (const uint8_t*)"MNOPQ", 5, panda::PANDA_CAN1);
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2, 2000);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x1\xFA""ABCDE", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x3\xFA""MNOPQ", LINE_INFO());
- }
-
- //Check that the order of the pass and block filter do not matter
- TEST_METHOD(J2534_CAN_RxAndFilterRemoval)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- auto filterid0 = J2534_set_BLOCK_filter(chanid, CAN, 0, 4, "\xFF\xFF\xFF\xFF", "\x0\x0\x02\xAC", LINE_INFO());
- auto filterid1 = J2534_set_PASS_filter(chanid, CAN, 0, 4, "\x0\x0\x0\x0", "\x0\x0\x0\x0", LINE_INFO());
-
- Assert::AreEqual(STATUS_NOERROR, PassThruStopMsgFilter(chanid, filterid0), _T("Failed to delete filter."), LINE_INFO());
-
- auto p = getPanda(500);
-
- p->can_send(0x1FA, FALSE, (const uint8_t*)"ABCDE", 5, panda::PANDA_CAN1);
- p->can_send(0x2AC, FALSE, (const uint8_t*)"HIJKL", 5, panda::PANDA_CAN1);
- p->can_send(0x3FA, FALSE, (const uint8_t*)"MNOPQ", 5, panda::PANDA_CAN1);
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 3, 1000);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x1\xFA""ABCDE", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x2\xAC""HIJKL", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[2], CAN, 0, 0, 5 + 4, 0, "\x0\x0\x3\xFA""MNOPQ", LINE_INFO());
- }
-
- //Check that the order of the pass and block filter do not matter
- TEST_METHOD(J2534_CAN_RxWithTimeout)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- J2534_set_PASS_filter(chanid, CAN, 0, 4, "\x0\x0\x0\x0", "\x0\x0\x0\x0", LINE_INFO());
- auto p = getPanda(500);
-
- PASSTHRU_MSG recvbuff;
- unsigned long msgcount = 1;
- unsigned int res = PassThruReadMsgs(chanid, &recvbuff, &msgcount, 100); // Here is where we test the timeout
- Assert::AreEqual(ERR_BUFFER_EMPTY, res, _T("No message should be found"), LINE_INFO());
- Assert::AreEqual(0, msgcount, _T("Received wrong number of messages."));
-
- //TODO Test that the timings work right instead of just testing it doesn't crash.
- }
-
- TEST_METHOD(J2534_CAN_Baud)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 250000, LINE_INFO());
- auto p = getPanda(250);
-
- J2534_send_msg_checked(chanid, CAN, 0, 0, 0, 6, 6, "\x0\x0\x3\xAB""HI", LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- }
-
- TEST_METHOD(J2534_CAN_PeriodicMessageStartStop)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- auto msgid = J2534_start_periodic_msg_checked(chanid, CAN, 0, 6, 0, "\x0\x0\x3\xAB""HI", 100, LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 3, 250);
- Assert::AreEqual(STATUS_NOERROR, PassThruStopPeriodicMsg(chanid, msgid), _T("Failed to delete filter."), LINE_INFO());
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[2], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
-
- auto timediff_1_0 = msg_recv[1].recv_time - msg_recv[0].recv_time;
- auto timediff_2_1 = msg_recv[2].recv_time - msg_recv[1].recv_time;
-
- std::ostringstream stringStream1;
- stringStream1 << "times1: " << timediff_1_0 << ", " << timediff_2_1 << std::endl;
- Logger::WriteMessage(stringStream1.str().c_str());
-
- Assert::IsTrue(timediff_1_0 > 90000);
- Assert::IsTrue(timediff_1_0 < 110000);
- Assert::IsTrue(timediff_2_1 > 90000);
- Assert::IsTrue(timediff_2_1 < 110000);
-
- msg_recv = panda_recv_loop(p, 0, 300);
- }
-
- TEST_METHOD(J2534_CAN_PeriodicMessageMultipleStartStop)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- auto msgid0 = J2534_start_periodic_msg_checked(chanid, CAN, 0, 6, 0, "\x0\x0\x3\xAB""HI", 100, LINE_INFO());
- auto msgid1 = J2534_start_periodic_msg_checked(chanid, CAN, 0, 6, 0, "\x0\x0\x1\x23""YO", 80, LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 9, 370);
- Assert::AreEqual(STATUS_NOERROR, PassThruStopPeriodicMsg(chanid, msgid0), _T("Failed to delete filter."), LINE_INFO());
- Assert::AreEqual(STATUS_NOERROR, PassThruStopPeriodicMsg(chanid, msgid1), _T("Failed to delete filter."), LINE_INFO());
- //time diagram. 10 ms per character. * is send event. : is termination of periodic messages.
- //*---------*---------*---------*-----:----* HI
- //*-------*-------*-------*-------*---:----* YO
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x123, FALSE, FALSE, "YO", LINE_INFO());
- check_panda_can_msg(msg_recv[2], 0, 0x123, FALSE, FALSE, "YO", LINE_INFO());
- check_panda_can_msg(msg_recv[3], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[4], 0, 0x123, FALSE, FALSE, "YO", LINE_INFO());
- check_panda_can_msg(msg_recv[5], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[6], 0, 0x123, FALSE, FALSE, "YO", LINE_INFO());
- check_panda_can_msg(msg_recv[7], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[8], 0, 0x123, FALSE, FALSE, "YO", LINE_INFO());
-
- auto timediff_HI_3_0 = msg_recv[3].recv_time - msg_recv[0].recv_time;
- auto timediff_HI_5_3 = msg_recv[5].recv_time - msg_recv[3].recv_time;
- auto timediff_HI_7_5 = msg_recv[7].recv_time - msg_recv[5].recv_time;
-
- auto timediff_YO_2_1 = msg_recv[2].recv_time - msg_recv[1].recv_time;
- auto timediff_YO_4_2 = msg_recv[4].recv_time - msg_recv[2].recv_time;
- auto timediff_YO_6_4 = msg_recv[6].recv_time - msg_recv[4].recv_time;
- auto timediff_YO_8_6 = msg_recv[8].recv_time - msg_recv[6].recv_time;
-
- std::ostringstream stringStreamHi;
- stringStreamHi << "HiTimes: " << timediff_HI_3_0 << ", " << timediff_HI_5_3 << ", " << timediff_HI_7_5 << std::endl;
- Logger::WriteMessage(stringStreamHi.str().c_str());
-
- std::ostringstream stringStreamYo;
- stringStreamYo << "HiTimes: " << timediff_YO_2_1 << ", " << timediff_YO_4_2 << ", " << timediff_YO_6_4 << ", " << timediff_YO_8_6 << std::endl;
- Logger::WriteMessage(stringStreamYo.str().c_str());
-
- Assert::IsTrue(timediff_HI_3_0 > 90000);
- Assert::IsTrue(timediff_HI_3_0 < 110000);
- Assert::IsTrue(timediff_HI_5_3 > 90000);
- Assert::IsTrue(timediff_HI_5_3 < 110000);
- Assert::IsTrue(timediff_HI_7_5 > 90000);
- Assert::IsTrue(timediff_HI_7_5 < 110000);
-
- Assert::IsTrue(timediff_YO_2_1 > 80000-10000);
- Assert::IsTrue(timediff_YO_2_1 < 80000+1000);
- Assert::IsTrue(timediff_YO_4_2 > 80000 - 10000);
- Assert::IsTrue(timediff_YO_4_2 < 80000 + 10000);
- Assert::IsTrue(timediff_YO_6_4 > 80000 - 10000);
- Assert::IsTrue(timediff_YO_6_4 < 80000 + 10000);
- Assert::IsTrue(timediff_YO_8_6 > 80000 - 10000);
- Assert::IsTrue(timediff_YO_8_6 < 80000 + 10000);
-
- msg_recv = panda_recv_loop(p, 0, 300);
- }
-
- TEST_METHOD(J2534_CAN_PeriodicMessageStartStop_Loopback)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO()); // ENABLE J2534 ECHO/LOOPBACK
- auto p = getPanda(500);
- auto msgid = J2534_start_periodic_msg_checked(chanid, CAN, 0, 6, 0, "\x0\x0\x3\xAB""HI", 100, LINE_INFO());
-
- std::vector msg_recv = panda_recv_loop(p, 3, 250);
- Assert::AreEqual(STATUS_NOERROR, PassThruStopPeriodicMsg(chanid, msgid), _T("Failed to delete filter."), LINE_INFO());
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[2], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 3);
- check_J2534_can_msg(j2534_msg_recv[0], CAN, TX_MSG_TYPE, 0, 6, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], CAN, TX_MSG_TYPE, 0, 6, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[2], CAN, TX_MSG_TYPE, 0, 6, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
-
- auto timediff_1_0 = j2534_msg_recv[1].Timestamp - j2534_msg_recv[0].Timestamp;
- auto timediff_2_1 = j2534_msg_recv[2].Timestamp - j2534_msg_recv[1].Timestamp;
-
- std::ostringstream stringStream1;
- stringStream1 << "times1: " << timediff_1_0 << ", " << timediff_2_1 << std::endl;
- Logger::WriteMessage(stringStream1.str().c_str());
-
- Assert::IsTrue(timediff_1_0 > 90000);
- Assert::IsTrue(timediff_1_0 < 110000);
- Assert::IsTrue(timediff_2_1 > 90000);
- Assert::IsTrue(timediff_2_1 < 110000);
-
- msg_recv = panda_recv_loop(p, 0, 300);
- }
-
- TEST_METHOD(J2534_CAN_PeriodicMessageWithTx)
- {
- auto chanid = J2534_open_and_connect("", CAN, 0, 500000, LINE_INFO());
- auto p = getPanda(500);
- auto msgid = J2534_start_periodic_msg_checked(chanid, CAN, 0, 6, 0, "\x0\x0\x3\xAB""HI", 100, LINE_INFO());
-
- J2534_send_msg(chanid, CAN, 0, 0, 0, 7, 0, "\x0\x0\x3\xAB""LOL");
-
- std::vector msg_recv = panda_recv_loop(p, 4, 250);
- Assert::AreEqual(STATUS_NOERROR, PassThruStopPeriodicMsg(chanid, msgid), _T("Failed to delete filter."), LINE_INFO());
- check_panda_can_msg(msg_recv[0], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[1], 0, 0x3AB, FALSE, FALSE, "LOL", LINE_INFO());//Staggered write inbetween multiple scheduled TXs
- check_panda_can_msg(msg_recv[2], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
- check_panda_can_msg(msg_recv[3], 0, 0x3AB, FALSE, FALSE, "HI", LINE_INFO());
-
- auto timediff_2_0 = msg_recv[2].recv_time - msg_recv[0].recv_time;
- auto timediff_3_2 = msg_recv[3].recv_time - msg_recv[2].recv_time;
-
- std::ostringstream stringStream1;
- stringStream1 << "times1: " << timediff_2_0 << ", " << timediff_3_2 << std::endl;
- Logger::WriteMessage(stringStream1.str().c_str());
-
- Assert::IsTrue(timediff_2_0 > 90000);
- Assert::IsTrue(timediff_2_0 < 110000);
- Assert::IsTrue(timediff_3_2 > 90000);
- Assert::IsTrue(timediff_3_2 < 110000);
-
- msg_recv = panda_recv_loop(p, 0, 300);
- }
-
- TEST_METHOD(J2534_CAN_BaudInvalid)
- {
- unsigned long chanid;
- Assert::AreEqual(STATUS_NOERROR, open_dev(""), _T("Failed to open device."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_BAUDRATE, PassThruConnect(devid, CAN, 0, 6000000, &chanid), _T("Baudrate should have been invalid."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_BAUDRATE, PassThruConnect(devid, CAN, 0, 200, &chanid), _T("Baudrate should have been invalid."), LINE_INFO());
- Assert::AreEqual(ERR_INVALID_BAUDRATE, PassThruConnect(devid, CAN, 0, 250010, &chanid), _T("Baudrate should have been invalid."), LINE_INFO());
- }
-
- bool didopen = FALSE;
- unsigned long devid;
-
- unsigned long open_dev(const char* name, long assert_err = STATUS_NOERROR, TCHAR* failmsg = _T("Failed to open device.")) {
- unsigned int res = PassThruOpen((void*)name, &devid);
- if (res == STATUS_NOERROR) didopen = TRUE;
- return res;
- }
-
- unsigned long J2534_open_and_connect(const char* name, unsigned long ProtocolID, unsigned long Flags, unsigned long bps, const __LineInfo* pLineInfo = NULL) {
- unsigned long chanid;
- Assert::AreEqual(STATUS_NOERROR, open_dev(name), _T("Failed to open device."), pLineInfo);
- Assert::AreEqual(STATUS_NOERROR, PassThruConnect(devid, ProtocolID, Flags, bps, &chanid), _T("Failed to open channel."), pLineInfo);
- write_ioctl(chanid, LOOPBACK, FALSE, LINE_INFO()); // DISABLE J2534 ECHO/LOOPBACK
- return chanid;
- }
-
- };
-
- TEST_CLASS(J2534DeviceISO15765)
- {
- public:
-
- TEST_METHOD_INITIALIZE(init) {
- LoadJ2534Dll("pandaJ2534_0404_32.dll");
- }
-
- TEST_METHOD_CLEANUP(deinit) {
- if (didopen) {
- PassThruClose(devid);
- didopen = FALSE;
- }
- UnloadJ2534Dll();
- }
-
- //Test that the BAUD rate of a ISO15765 connection can be changed.
- TEST_METHOD(J2534_ISO15765_SetBaud)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, 0, 500000, LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO()); // ENABLE J2534 ECHO/LOOPBACK
- auto p = getPanda(250);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, 0, 0, 4 + 2, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
- j2534_recv_loop(chanid, 0);
- panda_recv_loop(p, 0);
-
- write_ioctl(chanid, DATA_RATE, 250000, LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, TX_INDICATION, 0, 4, 0, "\x0\x0\x3\xAB", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, TX_MSG_TYPE, 0, 4 + 2, 0, "\x0\x0\x3\xAB""HI", LINE_INFO());
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x3AB, FALSE, FALSE, "\x2""HI", LINE_INFO());
- }
-
- ///////////////////// Tests checking things don't send/receive /////////////////////
-
- //Check tx PASSES and rx FAIL WITHOUT a filter. 29 bit. NO Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_PassTxFailRx_29b_NoFilter_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- //TX: works because all single frame writes should work (with or without a flow contorl filter)
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x07""TX_TEST", LINE_INFO());
-
- //RX: Reads require a flow control filter, and should fail without one.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x06\x41\x00\xff\xff\xff\xfe", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
- }
-
- //Check tx and rx FAIL WITHOUT a filter. 29 bit. NO Filter. NoPadding. STD address. First Frame.
- TEST_METHOD(J2534_ISO15765_FailTxRx_29b_NoFilter_NoPad_STD_FF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- auto p = getPanda(500);
-
- //TX
- Assert::AreEqual(ERR_NO_FLOW_CONTROL, J2534_send_msg(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 12, 0, "\x18\xda\xef\xf1\xA1\xB2\xC3\xD4\xE5\xF6\x09\x1A"),
- _T("Should fail to tx without a filter."), LINE_INFO());
- j2534_recv_loop(chanid, 0);
- panda_recv_loop(p, 0);
-
- //RX; Send full response and check didn't receive flow control from J2534 device
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x14\x49\x02\x01""1D4", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""GP00R55", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""B123456", 8, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);//Check a full message is not accepted.
- }
-
- //Check tx PASSES and rx FAIL with a MISMATCHED filter. 29 bit. Mismatch Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_PassTxFailRx_29b_MismatchFilter_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //TX: works because all single frame writes should work (with or without a flow contorl filter)
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 6, 0, "\x18\xda\xe0\xf1""\x11\x22", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xe0\xf1", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAE0F1, TRUE, FALSE, "\x02""\x11\x22", LINE_INFO());
-
- //RX. Send ISO15765 single frame to device. Address still doesn't match filter, so should not be received.
- checked_panda_send(p, 0x18DAF1E0, TRUE, "\x06\x41\x00\xff\xff\xff\xfe", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
- }
-
- //Check tx and rx FAIL with a MISMATCHED filter. 29 bit. Mismatch Filter. NoPadding. STD address. First Frame.
- TEST_METHOD(J2534_ISO15765_FailTxRx_29b_MismatchFilter_NoPad_STD_FF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //TX
- Assert::AreEqual(ERR_NO_FLOW_CONTROL, J2534_send_msg(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 12, 0, "\x18\xda\xe0\xf1""USELESS STUFF"),
- _T("Should fail to tx without a filter."), LINE_INFO());
- j2534_recv_loop(chanid, 0);
- panda_recv_loop(p, 0);
-
- //RX; Send a full response and check didn't receive flow control from J2534 device
- checked_panda_send(p, 0x18DAF1E0, TRUE, "\x10\x14\x49\x02\x01""1D4", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1E0, TRUE, "\x21""GP00R55", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1E0, TRUE, "\x22""B123456", 8, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);//Check a full message is not accepted.
- }
-
- //Check tx FAILS with a MISMATCHED filter 29bit flag. 29 bit. Mismatch Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_FailTxRx_29b_MismatchFilterFlag29b_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x0\x0\x1\xab", "\x0\x0\x1\xcd", LINE_INFO());
- auto p = getPanda(500);
-
- //TX
- Assert::AreEqual(ERR_INVALID_MSG, J2534_send_msg(chanid, ISO15765, 0, 0, 0, 6, 0, "\x0/x0/x1/xcd\x01\x00"),
- _T("mismatched address should fail to tx."), LINE_INFO());
- j2534_recv_loop(chanid, 0);
- panda_recv_loop(p, 0);
-
- //RX. Send ISO15765 single frame to device. Address still doesn't match filter, so should not be received.
- checked_panda_send(p, 0x1ab, FALSE, "\x06\x41\x00\xff\xff\xff\xfe", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
- }
-
- ///////////////////// Tests checking things actually send/receive. Standard Addressing /////////////////////
-
- //Check rx passes with filter. 29 bit. Good Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessRx_29b_Filter_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x07""ABCD123", 8, 0, LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID, 0, 11, 11, "\x18\xda\xf1\xef""ABCD123", LINE_INFO());
- }
-
- //Check tx passes with filter. 29 bit. Good Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x07""TX_TEST", LINE_INFO());
- }
-
- //Check tx passes with filter. 29 bit. Good Filter. NoPadding. STD address. Single Frame. Loopback.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_SF_LOOPBACK)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x07""TX_TEST", LINE_INFO());
- }
-
- //Check rx passes with filter. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_SuccessRx_29b_Filter_NoPad_STD_FFCF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ninete", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the rest of the message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""en byte", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""s here", 7, 0, LINE_INFO());
-
- //Check J2534 constructed the whole message
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID, 0, 4 + 0x13, 4 + 0x13, "\x18\xda\xf1\xef""nineteen bytes here", LINE_INFO());
- }
-
- //Check multi frame tx passes with filter. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_FFCF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 14, 0, "\x18\xda\xef\xf1""\xAA\xBB\xCC\xDD\xEE\xFF\x11\x22\x33\x44", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 0); // No TxDone msg until after the final tx frame is sent
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x0A""\xAA\xBB\xCC\xDD\xEE\xFF", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x0\x0", 3, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""\x11\x22\x33\x44", LINE_INFO());
-
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- }
-
- //Check rx passes with filter. 11 bit. Good Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessRx_11b_Filter_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, 0, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, 0, 4, "\xff\xff\xff\xff", "\x0\x0\x1\xab", "\x0\x0\x1\xcd", LINE_INFO());
- auto p = getPanda(500);
-
- checked_panda_send(p, 0x1ab, FALSE, "\x07""ABCD123", 8, 0, LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, 0, 0, 11, 11, "\x0\x0\x1\xab""ABCD123", LINE_INFO());
- }
-
- //Check tx passes with filter. 11 bit. Good Filter. NoPadding. STD address. Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessTx_11b_Filter_NoPad_STD_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, 0, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, 0, 4, "\xff\xff\xff\xff", "\x0\x0\x1\xab", "\x0\x0\x1\xcd", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, 0, 0, 11, 0, "\x0\x0\x1\xcd""TX_TEST", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, TX_INDICATION, 0, 4, 0, "\x0\x0\x1\xcd", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x1CD, FALSE, FALSE, "\x07""TX_TEST", LINE_INFO());
- }
-
- //Check tx passes with filter multiple times. 29 bit. Good Filter. NoPadding. STD address. Multiple Single Frames.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MultipleSF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 9, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 4);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[2], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[3], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 9, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x07""TX_TEST", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x05""HELLO", LINE_INFO());
- }
-
- //Check that receiver's flow control block size requests are respected. 29 bit. Good Filter. NoPadding. STD address. Multiple Frames with multiple flow control.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MF_FLOWCONTROLBlockSize)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 52, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXXYYZZ", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x34""AABBCC", LINE_INFO());
-
- // [flow_status, block_size, st_min]
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x01\x00", 3, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x02\x00", 3, 2, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x01\x00", 3, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x00\x00", 3, 3, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x27""YYZZ", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- }
-
- //Check that receiver's flow control separation time requests are respected. 29 bit. Good Filter. NoPadding. STD address. Multiple Frames with multiple flow control.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MF_FLOWCONTROLSTMinMultiFc)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 52, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXXYYZZ", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x34""AABBCC", LINE_INFO());
-
- // [flow_status, block_size, st_min]
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x03\x0A", 3, 3, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- auto timediff0_1_0 = panda_msg_recv[1].recv_time - panda_msg_recv[0].recv_time;
- auto timediff0_2_1 = panda_msg_recv[2].recv_time - panda_msg_recv[1].recv_time;
-
- std::ostringstream stringStream0;
- stringStream0 << "times0: " << timediff0_1_0 << ", " << timediff0_2_1 << std::endl;
- Logger::WriteMessage(stringStream0.str().c_str());
-
- Assert::IsTrue(timediff0_1_0 > 10000);
- Assert::IsTrue(timediff0_1_0 < 32000);//Flexible, but trying to make sure things don't just all lag for a second or something
- Assert::IsTrue(timediff0_2_1 > 10000);
- Assert::IsTrue(timediff0_2_1 < 32000);
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x04\x20", 3, 4, LINE_INFO(), 500);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x27""YYZZ", LINE_INFO());
- auto timediff1_1_0 = panda_msg_recv[1].recv_time - panda_msg_recv[0].recv_time;
- auto timediff1_2_1 = panda_msg_recv[2].recv_time - panda_msg_recv[1].recv_time;
- auto timediff1_3_2 = panda_msg_recv[3].recv_time - panda_msg_recv[2].recv_time;
-
- std::ostringstream stringStream1;
- stringStream1 << "times1: " << timediff1_1_0 << ", " << timediff1_2_1 << ", " << timediff1_3_2 << std::endl;
- Logger::WriteMessage(stringStream1.str().c_str());
-
- Assert::IsTrue(timediff1_1_0 > 32000);
- Assert::IsTrue(timediff1_2_1 > 32000);
- Assert::IsTrue(timediff1_3_2 > 32000);
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- }
-
- //Check that receiver's flow control separation time requests are respected 2. 29 bit. Good Filter. NoPadding. STD address. Multiple Frames with one flow control.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MF_FLOWCONTROLSTMinSingleFc)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 52, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXXYYZZ", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x34""AABBCC", LINE_INFO());
-
- // [flow_status, block_size, st_min]
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x07\x0A", 3, 7, LINE_INFO(), 500);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[4], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[5], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[6], 0, 0x18DAEFF1, TRUE, FALSE, "\x27""YYZZ", LINE_INFO());
-
- auto timediff_1_0 = panda_msg_recv[1].recv_time - panda_msg_recv[0].recv_time;
- auto timediff_2_1 = panda_msg_recv[2].recv_time - panda_msg_recv[1].recv_time;
- auto timediff_3_2 = panda_msg_recv[3].recv_time - panda_msg_recv[2].recv_time;
- auto timediff_4_3 = panda_msg_recv[4].recv_time - panda_msg_recv[3].recv_time;
- auto timediff_5_4 = panda_msg_recv[5].recv_time - panda_msg_recv[4].recv_time;
- auto timediff_6_5 = panda_msg_recv[6].recv_time - panda_msg_recv[5].recv_time;
-
- std::ostringstream stringStream1;
- stringStream1 << "times1: " << timediff_1_0 << ", " << timediff_2_1 << ", " << timediff_3_2 <<
- ", " << timediff_4_3 << ", " << timediff_5_4 << ", " << timediff_6_5 << std::endl;
- Logger::WriteMessage(stringStream1.str().c_str());
-
- Assert::IsTrue(timediff_1_0 > 10000);
- Assert::IsTrue(timediff_2_1 > 10000);
- Assert::IsTrue(timediff_3_2 > 10000);
- Assert::IsTrue(timediff_4_3 > 10000);
- Assert::IsTrue(timediff_5_4 > 10000);
- Assert::IsTrue(timediff_6_5 > 10000);
- }
-
- //Check that tx works for messages with more than 16 frames. 29 bit. Good Filter. NoPadding. STD address. Large multiframe message.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MF_LotsOfFrames)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 125, 0,
- "\x18\xda\xef\xf1"
- "AABBCC""DDEEFFG""GHHIIJJ""KKLLMMN""NOOPPQQ""RRSSTTU""UVVWWXX""YYZZ112""2334455""6677889"
- "900abcd""efghijk""lmnopqr""stuvwxy""z!@#$%^""&*()_+-""=`~ABCD""EFGHIJK", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x7D""AABBCC", LINE_INFO());
-
- // [flow_status, block_size, st_min]
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x00\x00", 3, 17, LINE_INFO(), 1000);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[4], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[5], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[6], 0, 0x18DAEFF1, TRUE, FALSE, "\x27""YYZZ112", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[7], 0, 0x18DAEFF1, TRUE, FALSE, "\x28""2334455", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[8], 0, 0x18DAEFF1, TRUE, FALSE, "\x29""6677889", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[9], 0, 0x18DAEFF1, TRUE, FALSE, "\x2A""900abcd", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[10], 0, 0x18DAEFF1, TRUE, FALSE, "\x2B""efghijk", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[11], 0, 0x18DAEFF1, TRUE, FALSE, "\x2C""lmnopqr", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[12], 0, 0x18DAEFF1, TRUE, FALSE, "\x2D""stuvwxy", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[13], 0, 0x18DAEFF1, TRUE, FALSE, "\x2E""z!@#$%^", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[14], 0, 0x18DAEFF1, TRUE, FALSE, "\x2F""&*()_+-", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[15], 0, 0x18DAEFF1, TRUE, FALSE, "\x20""=`~ABCD", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[16], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""EFGHIJK", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- }
-
- //Check tx passes with filter multiple times. 29 bit. Good Filter. NoPadding. STD address. Multiple Single Frames.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MultipleMFSF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 23, 0, "\x18\xda\xef\xf1""Long data because I can", LINE_INFO());
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 9, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x17""Long d", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x00\x00", 3, 4, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""ata bec", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""ause I ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""can", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x05""HELLO", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 4);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 23, 0, "\x18\xda\xef\xf1""Long data because I can", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[2], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[3], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 5, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
- }
-
- //Check tx passes after message timeout. 29 bit. Good Filter. NoPadding. STD address. Multiple Frame timeout then Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MFTimeoutSFSuccess)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 23, 0, "\x18\xda\xef\xf1""Long data because I can", LINE_INFO());
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 9, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 2, 1000);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x17""Long d", LINE_INFO()); //First Frame. Not replying so it needs to time out.
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x05""HELLO", LINE_INFO()); //Reply to the next message.
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 5, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
- }
-
- //Check tx passes after mid-message timeout. 29 bit. Good Filter. NoPadding. STD address. Multiple Frame mid-timeout then Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MFMidTimeoutSFSuccess)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 23, 0, "\x18\xda\xef\xf1""Long data because I can", LINE_INFO());
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 9, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x17""Long d", LINE_INFO()); //First Frame. Not replying so it needs to time out.
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x01\x00", 3, 2, LINE_INFO(), 1000);//Start a conversation
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""ata bec", LINE_INFO());//Check passthru device sent more data, but don't reply to it
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x05""HELLO", LINE_INFO()); //Reply to the next message.
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 5, 0, "\x18\xda\xef\xf1""HELLO", LINE_INFO());
- }
-
- //Check slow tx passes without hitting FC timeout. 29 bit. Good Filter. NoPadding. STD address. Long STmin, catches if FC timeout applies before needed.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_SLOWMF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x06\x7F", 3, 6, LINE_INFO(), 3000);//Start a conversation... but slow. FC timeout is 250 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());//Check this convo doesn't trigger that timeout.
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[4], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());//Some of these should fail to recv if there is an issue.
- check_panda_can_msg(panda_msg_recv[5], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
- }
-
- //Check MF tx can be sent along side of a periodic message. 29 bit. Good Filter. NoPadding. STD address. Long STmin, checks that MF tx and periodic TX don't break each other.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_SLOWMF_WithPeriodicMsg)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- //Timing diagram of this test.
- //* is a periodic msg transfer; F is first frame, L is Flow control, C is Consecutive Frame.
- // *~~~~~~~*~~~~~~~*~~~~~~~* (The alignment here is unimportant. The exact order is not checked.
- //F C----C----C----C----C----C (100 ms between Cs)
- // L
-
- auto msgid = J2534_start_periodic_msg_checked(chanid, ISO15765, CAN_29BIT_ID, 6, 0, "\x18\xda\xef\xf1""HI", 130, LINE_INFO());
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x02""HI", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- Assert::IsTrue(p->can_send(0x18DAF1EF, TRUE, (const uint8_t*)"\x30\x06\x64", 3, panda::PANDA_CAN1), _T("Panda send says it failed."), LINE_INFO());
-
- Timer t_permsg = Timer();
- Timer t_MFmsg = Timer();
- unsigned int MFframesReceived = 0;
- unsigned int PeriodicMsgReceived = 1; //Because of the first panda_recv_loop above.
- std::array const mfMsgExpectedParts{ "\x21""DDEEFFG", "\x22""GHHIIJJ", "\x23""KKLLMMN", "\x24""NOOPPQQ", "\x25""RRSSTTU", "\x26""UVVWWXX" };
-
- while (TRUE) {
- std::vectormsg_recv = p->can_recv();
- for (auto msg : msg_recv) {
- if (msg.is_receipt) continue;
- if ((msg.dat[0] & 0xf0) == 0x20) {
- Assert::AreEqual(mfMsgExpectedParts[MFframesReceived], std::string((const char*)msg.dat, msg.len), _T("Got wrong part of MF msg."), LINE_INFO());
- MFframesReceived++;
- t_MFmsg.reset();
- } else if (std::string((const char*)msg.dat, msg.len) == "\x02HI") {
- PeriodicMsgReceived++;
- t_permsg.reset();
- } else {
- Assert::IsTrue(FALSE, _T("Got impossible message. Something is very wrong. Check other tests."), LINE_INFO());
- }
- }
-
- if (MFframesReceived >= 6) break;
- Assert::IsTrue(300 > t_permsg.getTimePassed(), _T("Timed out waiting for periodic msessage frame."), LINE_INFO());
- Assert::IsTrue(300 > t_MFmsg.getTimePassed(), _T("Timed out waiting for multiframe msessage frame."), LINE_INFO());
-
- if (msg_recv.size() == 0)
- Sleep(10);
- }
-
- //Stop the periodic message and grab any data it may have sent since we last checked.
- //Not sure if this is needed.
- Assert::AreEqual(STATUS_NOERROR, PassThruStopPeriodicMsg(chanid, msgid), _T("Failed to delete filter."), LINE_INFO());
- auto extra_panda_msg = panda_recv_loop_loose(p, 0, 200);
- for (auto msg : extra_panda_msg) {
- if (std::string((const char*)msg.dat, msg.len) == "\x02HI") {
- PeriodicMsgReceived++;
- Logger::WriteMessage("Received extra periodic message.");
- } else {
- Assert::IsTrue(FALSE, _T("Got impossible message. Something is very wrong. Check other tests."), LINE_INFO());
- }
- }
-
- Assert::IsTrue(PeriodicMsgReceived > 3, _T("Did not receive enough periodic messages. Likely canceled or delayed."), LINE_INFO());
-
- std::ostringstream stringStream;
- stringStream << "PeriodicMsgReceived = " << PeriodicMsgReceived << std::endl;
- Logger::WriteMessage(stringStream.str().c_str());
-
- unsigned int periodicTxIndicationCount = 0;
- unsigned int TxIndicationCount = 0;
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2 + (PeriodicMsgReceived * 2));
- for (int i = 0; i < PeriodicMsgReceived + 1; i++) {
- check_J2534_can_msg(j2534_msg_recv[(i * 2) + 0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- switch (j2534_msg_recv[(i * 2) + 1].DataSize) {
- case 4 + 2:
- check_J2534_can_msg(j2534_msg_recv[(i * 2) + 1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 2, 0, "\x18\xda\xef\xf1""HI", LINE_INFO());
- break;
- case 4 + 48:
- check_J2534_can_msg(j2534_msg_recv[(i * 2) + 1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
- break;
- default:
- Assert::IsTrue(FALSE, _T("Got unexpected data!"), LINE_INFO());
- }
- }
-
- Assert::AreNotEqual(PeriodicMsgReceived, periodicTxIndicationCount, _T("Wrong number of periodic msgs reported by passthru device."), LINE_INFO());
- Assert::AreNotEqual(1, TxIndicationCount, _T("Wrong number of TX msgs reported by passthru device."), LINE_INFO());
- }
-
- ///////////////////// Tests checking things break or recover during send/receive /////////////////////
-
- //Check rx FAILS when frame is dropped. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_FailRx_29b_Filter_NoPad_STD_FFCF_DropFrame)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ninete", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the rest of the message
- //Missing the 2nd frame "\x21""en byte"
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""s here", 7, 0, LINE_INFO());
-
- //Check J2534 DOES NOT construct the incomplete message
- j2534_recv_loop(chanid, 0);
- }
-
- //Check rx ignores frames that arrive out of order. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_PassRx_29b_Filter_NoPad_STD_FFCF_FrameNumSkip)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ABCDEF", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the rest of the message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""XXXXXX", 7, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""GHIJKLM", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x23""ZZZZZZ", 7, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""NOPQRS", 7, 0, LINE_INFO());
-
- //Check J2534 constructa the complete message from the correctly numbered frames.
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID, 0, 4 + 0x13, 4 + 0x13, "\x18\xda\xf1\xef""ABCDEFGHIJKLMNOPQRS", LINE_INFO());
- }
-
- //Check Single Frame rx RESETS ongoing multiframe transmission. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_PassRx_29b_Filter_NoPad_STD_SFRxResetsMFRx)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ABCDEF", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the next part of the message multi message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""GHIJKLM", 8, 0, LINE_INFO());
-
- //ABORTING MESSAGE
- //Send a NEW single frame message and check the J2534 device gets it (but not the original message it was receiving.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x06""ABC123", 7, 0, LINE_INFO());
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID, 0, 10, 10, "\x18\xda\xf1\xef""ABC123", LINE_INFO());
-
- //Resume sending the old message, and check th eJ2534 device didn't get a message.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""NOPQRS", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
- }
-
- //The documentation says that a s ingle channel can not send and receive messages trhough a
- //single conversation (flow control filter) at the same time. However, the required behavior
- //when this is detected is not described. This test was my best understanding of how it was
- //wanted, but I no longer see the point. For now I am disabling it.
- /*//Check Single Frame tx RESETS ongoing multiframe rx transmission. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_PassRx_29b_Filter_NoPad_STD_SFTxResetsMFRx)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ABCDEF", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the next part of the message multi message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""GHIJKLM", 8, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
-
- //ABORTING MESSAGE
- //Send a NEW single frame message and check the J2534 device gets it (but not the original message it was receiving.
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 11, 0, "\x18\xda\xef\xf1""TX_TEST", LINE_INFO());
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
-
- panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x07""TX_TEST", LINE_INFO());
- ///////////////////////////
-
- //Resume sending the old message, and check th eJ2534 device didn't get a message.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""NOPQRS", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
- }*/
-
- //TODO check rx is cleared by tx (multi). Or not.... read above note.
-
- //Check multiframe rx RESETS ongoing multiframe transmission. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_PassRx_29b_Filter_NoPad_STD_FFCF_MFRxResetsMFRx)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ABCDEF", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the next part of the multi message A
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""GHIJKLM", 8, 0, LINE_INFO());
-
- //ABORTING MESSAGE A
- //Send a NEW multi frame message (B) and check the J2534 device gets it (but not the original message it was receiving.
- //Send first frame, then check we get a flow control frame
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ninete", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the rest of the message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""en byte", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""s here", 7, 0, LINE_INFO());
-
- //Check J2534 constructed the whole message
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID, 0, 4 + 0x13, 4 + 0x13, "\x18\xda\xf1\xef""nineteen bytes here", LINE_INFO());
- //////////////////////// End sending B
-
- //Resume sending the multi message A, and check th eJ2534 device didn't get a message.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""NOPQRS", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
- }
-
- //Check rx fails gracefully if final CF of MF rx is too short. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_FailRxFinalCFTooShort_29b_Filter_NoPad_STD_FFCF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ninete", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x30\x00\x00", 3), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE, 0, 4, 0, "\x18\xda\xf1\xef", LINE_INFO());
-
- //Send the rest of the message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""en byte", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""s her", 6, 0, LINE_INFO()); //The transaction should reset here because more data could have been sent.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x23""e", 2, 0, LINE_INFO());
-
- //Check J2534 constructed the whole message
- j2534_msg_recv = j2534_recv_loop(chanid, 0);
- }
-
- //Check rx fails gracefully if first frame is too short. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_FailRxFFTooShort_29b_Filter_NoPad_STD_FFCF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame. The transaction should reset immediately because more data could have been sent in this frame.
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x10\x13""ninet", 7, 0, LINE_INFO());
- j2534_recv_loop(chanid, 0);
-
- //Send the rest of the message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x21""een byt", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x22""es here", 8, 0, LINE_INFO());
-
- //Check J2534 constructed the whole message
- j2534_recv_loop(chanid, 0);
- }
-
- //Check MF tx will stop upon receiving a flow control ABORT. 29 bit. Good Filter. NoPadding. STD address. Large STmin, then abort, then send SF.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD__MF_FCAbort_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x02\x20", 3, 2, LINE_INFO());//Start a conversation. FC timeout is 32 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x32\x0\x0", 3, 0, LINE_INFO());//Abort the conversation
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 4, 0, "\x18\xda\xef\xf1""SUP!", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 4, 0, "\x18\xda\xef\xf1""SUP!", LINE_INFO());
- }
-
- //Check MF tx will stop upon receiving a flow control ABORT during valid blocksize. 29 bit. Good Filter. NoPadding. STD address. Large STmin, then mid tx abort, then send SF.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD__MF_FCMixTXAbort_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x06\x7F", 3, 1, LINE_INFO(), 200);//Start a conversation. FC timeout is 127 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x32\x0\x0", 3, 0, LINE_INFO());//Abort the conversation
- panda_recv_loop(p, 0, 200);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 4, 0, "\x18\xda\xef\xf1""SUP!", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 4, 0, "\x18\xda\xef\xf1""SUP!", LINE_INFO());
- }
-
- //Check slow tx can be stalled past timeout with CF WAIT frames. 29 bit. Good Filter. NoPadding. STD address. MF tx that would timeout without WAIT frames.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MFWithWaitFrames)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- write_ioctl(chanid, ISO15765_WFT_MAX, 10, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x02\x40", 3, 2, LINE_INFO(), 3000);//Start a conversation. FC timeout is 250 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
-
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x0\x0", 3, 4, LINE_INFO(), 3000);//Start a conversation. FC timeout is 250 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());//Some of these should fail to recv if there is an issue.
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
- }
-
- //Check slow tx can be stalled past timeout with CF WAIT frames during normal TX. 29 bit. Good Filter. NoPadding. STD address. Stalling working MF tx.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MFWithMidTXWaitFrames)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- write_ioctl(chanid, ISO15765_WFT_MAX, 10, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x06\x64", 3, 2, LINE_INFO(), 120);//Start a conversation. STmin 100. FC timeout is 250 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x0\x0", 3, 4, LINE_INFO(), 3000);//Start a conversation. FC timeout is 250 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[2], 0, 0x18DAEFF1, TRUE, FALSE, "\x25""RRSSTTU", LINE_INFO());//Some of these should fail to recv if there is an issue.
- check_panda_can_msg(panda_msg_recv[3], 0, 0x18DAEFF1, TRUE, FALSE, "\x26""UVVWWXX", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
- }
-
- //Check that too many WAIT frames will abort the transfer. 29 bit. Good Filter. NoPadding. STD address. Too much stalling causes abort.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_STD_MFTooManyWaitFrames)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID, 4, "\xff\xff\xff\xff", "\x18\xda\xf1\xef", "\x18\xda\xef\xf1", LINE_INFO());
- write_ioctl(chanid, LOOPBACK, TRUE, LINE_INFO());
- write_ioctl(chanid, ISO15765_WFT_MAX, 2, LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 48, 0, "\x18\xda\xef\xf1""AABBCCDDEEFFGGHHIIJJKKLLMMNNOOPPQQRRSSTTUUVVWWXX", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x10\x30""AABBCC", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x02\x64", 3, 2, LINE_INFO(), 120);//Start a conversation. STmin 100. FC timeout is 250 ms.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x21""DDEEFFG", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x22""GHHIIJJ", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x02\x64", 3, 2, LINE_INFO(), 120);//Resume the conversation.
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x23""KKLLMMN", LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, "\x24""NOOPPQQ", LINE_INFO());
-
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x31\x0\x0", 3, 0, LINE_INFO(), 100);//Delay the conversation.
- Sleep(100);
-
- //Should not resume because the conversation has been delayed too long.
- panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x30\x0\x0", 3, 0, LINE_INFO(), 300);
-
- //Send a SF message to check the tubes are not clogged.
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID, 0, 4 + 4, 0, "\x18\xda\xef\xf1""SUP!", LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 2);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION, 0, 4, 0, "\x18\xda\xef\xf1", LINE_INFO());
- check_J2534_can_msg(j2534_msg_recv[1], ISO15765, CAN_29BIT_ID | TX_MSG_TYPE, 0, 4 + 4, 0, "\x18\xda\xef\xf1""SUP!", LINE_INFO());
- }
-
- ///////////////////// Tests checking things actually send/receive. Ext 5 byte Addressing /////////////////////
-
- //Check rx passes with filter. 29 bit. Good Filter. NoPadding. EXT address. Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessRx_29b_Filter_NoPad_EXT_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 5, "\xff\xff\xff\xff\xff", "\x18\xda\xf1\xef\x13", "\x18\xda\xef\xf1\x13", LINE_INFO());
- auto p = getPanda(500);
-
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13""\x06""ABC123", 8, 0, LINE_INFO());
-
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 0, 11, 11, "\x18\xda\xf1\xef\x13""ABC123", LINE_INFO());
- }
-
- //Check tx passes with filter. 29 bit. Good Filter. NoPadding. EXT address. Single Frame.
- TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_EXT_SF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 5, "\xff\xff\xff\xff\xff", "\x18\xda\xf1\xef\x13", "\x18\xda\xef\xf1\x13", LINE_INFO());
- auto p = getPanda(500);
-
- J2534_send_msg_checked(chanid, ISO15765, 0, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 0, 11, 0, "\x18\xda\xef\xf1\x13""DERP!!", LINE_INFO());
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | TX_INDICATION | ISO15765_ADDR_TYPE, 0, 5, 0, "\x18\xda\xef\xf1\x13", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, "\x13""\x06""DERP!!", LINE_INFO());
- }
-
- //Check rx passes with filter. 29 bit. Good Filter. NoPadding. EXT address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_SuccessRx_29b_Filter_NoPad_EXT_FFCF)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 5, "\xff\xff\xff\xff\xff", "\x18\xda\xf1\xef\x13", "\x18\xda\xef\xf1\x13", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- Assert::IsTrue(p->can_send(0x18DAF1EF, TRUE, (const uint8_t*)"\x13""\x10\x13""ninet", 8, panda::PANDA_CAN1), _T("Panda send says it failed."), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE | ISO15765_ADDR_TYPE, 0, 5, 0, "\x18\xda\xf1\xef\x13", LINE_INFO());
-
- auto panda_msg_recv = panda_recv_loop(p, 2);
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAF1EF, TRUE, TRUE, std::string("\x13""\x10\x13""ninet", 8), LINE_INFO());
- check_panda_can_msg(panda_msg_recv[1], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x13""\x30\x00\x00", 4), LINE_INFO());
-
- //Send the rest of the message
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13""\x21""een by", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13""\x22""tes he", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13""\x23""re", 8, 0, LINE_INFO());
-
- //Check J2534 constructed the whole message
- j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 0, 5 + 0x13, 5 + 0x13, "\x18\xda\xf1\xef\x13""nineteen bytes here", LINE_INFO());
- }
-
- //Check tx passes with filter. 29 bit. Good Filter. NoPadding. EXT address. Multi Frame.
- /*TEST_METHOD(J2534_ISO15765_SuccessTx_29b_Filter_NoPad_EXT_FFCF)
- { //TODO when TX works with flow control}*/
-
- ///////////////////// Tests checking things break or recover during send/receive. Ext 5 byte Addressing /////////////////////
-
- //Check rx FAILS when frame is dropped. 29 bit. Good Filter. NoPadding. STD address. Multi Frame.
- TEST_METHOD(J2534_ISO15765_FailRx_29b_Filter_NoPad_EXT_FFCF_DropFrame)
- {
- auto chanid = J2534_open_and_connect("", ISO15765, CAN_29BIT_ID, 500000, LINE_INFO());
- J2534_set_flowctrl_filter(chanid, CAN_29BIT_ID | ISO15765_ADDR_TYPE, 5, "\xff\xff\xff\xff\xff", "\x18\xda\xf1\xef\x13", "\x18\xda\xef\xf1\x13", LINE_INFO());
- auto p = getPanda(500);
-
- //Send first frame, then check we get a flow control frame
- auto panda_msg_recv = checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13\x10\x13""ninet", 8, 1, LINE_INFO());
- check_panda_can_msg(panda_msg_recv[0], 0, 0x18DAEFF1, TRUE, FALSE, std::string("\x13\x30\x00\x00", 4), LINE_INFO());
-
- //Check first frame is registered with J2534
- auto j2534_msg_recv = j2534_recv_loop(chanid, 1);
- check_J2534_can_msg(j2534_msg_recv[0], ISO15765, CAN_29BIT_ID | START_OF_MESSAGE | ISO15765_ADDR_TYPE, 0, 5, 0, "\x18\xda\xf1\xef\x13", LINE_INFO());
-
- //Send the rest of the message
- //Missing the 2nd frame "\x13""\x21""een by"
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13""\x22""tes he", 8, 0, LINE_INFO());
- checked_panda_send(p, 0x18DAF1EF, TRUE, "\x13""\x23""re", 8, 0, LINE_INFO());
-
- //Check J2534 DOES NOT construct the incomplete message
- j2534_recv_loop(chanid, 0);
- }
-
- bool didopen = FALSE;
- unsigned long devid;
-
- unsigned long open_dev(const char* name, long assert_err = STATUS_NOERROR, TCHAR* failmsg = _T("Failed to open device.")) {
- unsigned int res = PassThruOpen((void*)name, &devid);
- if (res == STATUS_NOERROR) didopen = TRUE;
- return res;
- }
-
- unsigned long J2534_open_and_connect(const char* name, unsigned long ProtocolID, unsigned long Flags, unsigned long bps, const __LineInfo* pLineInfo = NULL) {
- unsigned long chanid;
- Assert::AreEqual(STATUS_NOERROR, open_dev(name), _T("Failed to open device."), pLineInfo);
- Assert::AreEqual(STATUS_NOERROR, PassThruConnect(devid, ProtocolID, Flags, bps, &chanid), _T("Failed to open channel."), pLineInfo);
- write_ioctl(chanid, LOOPBACK, FALSE, LINE_INFO()); // DISABLE J2534 ECHO/LOOPBACK
- return chanid;
- }
-
- };
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/pandaJ2534DLL Test.vcxproj b/panda/drivers/windows/pandaJ2534DLL Test/pandaJ2534DLL Test.vcxproj
deleted file mode 100644
index f19c74346..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/pandaJ2534DLL Test.vcxproj
+++ /dev/null
@@ -1,122 +0,0 @@
-
-
-
-
- Debug
- Win32
-
-
- Release
- Win32
-
-
-
- {7912F978-B48C-4C5D-8BFD-5D1E22158E47}
- Win32Proj
- pandaJ2534DLLTest
- 10.0.16299.0
- Tests
-
-
- DynamicLibrary
- true
- v141
- Unicode
- false
-
-
- DynamicLibrary
- false
- v141
- true
- Unicode
- false
-
-
-
-
-
-
-
-
-
-
- true
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
- true
- $(SolutionDir)$(Configuration)_$(PlatformShortName)\
-
-
-
- Use
- Level3
- Disabled
- $(VCInstallDir)UnitTest\include;%(AdditionalIncludeDirectories);$(SolutionDir)
- WIN32;_DEBUG;%(PreprocessorDefinitions)
- true
-
- Windows
- $(VCInstallDir)UnitTest\lib;%(AdditionalLibraryDirectories)
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)panda.lib
-
-
-
-
- Level3
- Use
- MaxSpeed
- true
- true
- $(VCInstallDir)UnitTest\include;%(AdditionalIncludeDirectories);$(SolutionDir)
- WIN32;NDEBUG;%(PreprocessorDefinitions)
- true
-
- Windows
- true
- true
- $(VCInstallDir)UnitTest\lib;%(AdditionalLibraryDirectories)
- kernel32.lib;user32.lib;gdi32.lib;winspool.lib;comdlg32.lib;advapi32.lib;shell32.lib;ole32.lib;oleaut32.lib;uuid.lib;odbc32.lib;odbccp32.lib;%(AdditionalDependencies);$(OutDir)panda.lib
-
-
-
-
-
-
- Create
- Create
-
-
-
-
- {96e0e646-ee76-444d-9a77-a0cd7f781deb}
-
-
- {a2bb18a5-f26b-48d6-bbb5-b83d64473c77}
-
-
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/pandaJ2534DLL Test.vcxproj.filters b/panda/drivers/windows/pandaJ2534DLL Test/pandaJ2534DLL Test.vcxproj.filters
deleted file mode 100644
index 476ce458d..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/pandaJ2534DLL Test.vcxproj.filters
+++ /dev/null
@@ -1,63 +0,0 @@
-
-
-
-
- {4FC737F1-C7A5-4376-A066-2A32D752A2FF}
- cpp;c;cc;cxx;def;odl;idl;hpj;bat;asm;asmx
-
-
- {93995380-89BD-4b04-88EB-625FBE52EBFB}
- h;hh;hpp;hxx;hm;inl;inc;xsd
-
-
- {67DA6AB6-F800-4c08-8B7A-83BB121AAD01}
- rc;ico;cur;bmp;dlg;rc2;rct;bin;rgs;gif;jpg;jpeg;jpe;resx;tiff;tif;png;wav;mfcribbon-ms
-
-
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
- Header Files
-
-
-
-
- Source Files
-
-
- Source Files
-
-
- Source Files
-
-
- Source Files
-
-
- Source Files
-
-
- Source Files
-
-
- Source Files
-
-
-
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/panda_tests.cpp b/panda/drivers/windows/pandaJ2534DLL Test/panda_tests.cpp
deleted file mode 100644
index 51b0bfcf2..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/panda_tests.cpp
+++ /dev/null
@@ -1,187 +0,0 @@
-#include "stdafx.h"
-#include "panda_shared/panda.h"
-#include "TestHelpers.h"
-
-#include
-
-using namespace Microsoft::VisualStudio::CppUnitTestFramework;
-using namespace panda;
-
-namespace pandaTestNative
-{
- TEST_CLASS(DeviceDiscovery)
- {
- public:
-
- TEST_METHOD(Panda_DevDiscover_ListDevices)
- {
- auto pandas_available = Panda::listAvailablePandas();
- Assert::IsTrue(pandas_available.size() > 0, _T("No pandas were found."));
- for (auto sn : pandas_available) {
- Assert::IsTrue(sn.size() == 24, _T("panda Serial Number not 24 characters long."));
- }
- }
-
- TEST_METHOD(Panda_DevDiscover_OpenFirstDevice)
- {
- auto pandas_available = Panda::listAvailablePandas();
- Assert::IsTrue(pandas_available.size() > 0, _T("No pandas were found."));
-
- auto p1 = Panda::openPanda(pandas_available[0]);
- Assert::IsFalse(p1 == nullptr, _T("Could not open panda."));
- }
-
- TEST_METHOD(Panda_DevDiscover_OpenDeviceNoName)
- {
- auto pandas_available = Panda::listAvailablePandas();
- Assert::IsTrue(pandas_available.size() > 0, _T("No pandas were found."));
-
- auto p1 = Panda::openPanda("");
- Assert::IsFalse(p1 == nullptr, _T("Could not open panda."));
- Assert::IsTrue(p1->get_usb_sn() == pandas_available[0], _T("Could not open panda."));
- }
-
- TEST_METHOD(Panda_DevDiscover_OpenDeviceUnavailable)
- {
- auto p1 = Panda::openPanda("ZZZZZZZZZZZZZZZZZZZZZZZZ");
- Assert::IsTrue(p1 == nullptr, _T("Invalid sn still worked."));
- }
-
- TEST_METHOD(Panda_DevDiscover_WillNotOpenAlreadyOpenedDevice)
- {
- auto pandas_available = Panda::listAvailablePandas();
- Assert::IsTrue(pandas_available.size() > 0, _T("No pandas were found."));
-
- auto p1 = Panda::openPanda(pandas_available[0]);
- Assert::IsFalse(p1 == nullptr, _T("Could not open panda."));
-
- auto p2 = Panda::openPanda(pandas_available[0]);
- Assert::IsTrue(p2 == nullptr, _T("Opened an already open panda."));
- }
-
- TEST_METHOD(Panda_DevDiscover_OpenedDeviceNotListed)
- {
- auto pandas_available = Panda::listAvailablePandas();
- Assert::IsTrue(pandas_available.size() > 0, _T("No pandas were found."));
-
- auto p1 = Panda::openPanda(pandas_available[0]);
- Assert::IsFalse(p1 == nullptr, _T("Could not open panda."));
-
- auto pandas_available2 = Panda::listAvailablePandas();
- for (auto sn : pandas_available2) {
- Assert::IsFalse(p1->get_usb_sn() == sn, _T("Opened panda appears in list of available pandas."));
- }
-
- }
- };
-
- TEST_CLASS(CANOperations)
- {
- public:
-
- TEST_METHOD(Panda_CAN_Echo)
- {
- auto p0 = getPanda(500, TRUE);
-
- uint32_t addr = 0xAA;
- bool is_29b = FALSE;
- uint8_t candata[8];
-
- for (auto canbus : { PANDA_CAN1, PANDA_CAN2, PANDA_CAN3 }) {
- uint8_t len = (rand() % 8) + 1;
- for (size_t i = 0; i < len; i++)
- candata[i] = rand() % 256;
-
- p0->can_send(addr, is_29b, candata, len, canbus);
- Sleep(10);
-
- auto can_msgs = p0->can_recv();
-
- Assert::AreEqual(2, can_msgs.size(), _T("Received the wrong number of CAN messages."), LINE_INFO());
-
- for (auto msg : can_msgs) {
- Assert::IsTrue(msg.addr == addr, _T("Wrong addr."));
- Assert::IsTrue(msg.bus == canbus, _T("Wrong bus."));
- Assert::IsTrue(msg.len == len, _T("Wrong len."));
- Assert::AreEqual(memcmp(msg.dat, candata, msg.len), 0, _T("Received CAN data not equal"));
- for (int i = msg.len; i < 8; i++)
- Assert::IsTrue(msg.dat[i] == 0, _T("Received CAN data not trailed by 0s"));
- }
-
- Assert::IsTrue(can_msgs[0].is_receipt, _T("Didn't get receipt."));
- Assert::IsFalse(can_msgs[1].is_receipt, _T("Didn't get echo."));
- }
- }
-
- TEST_METHOD(Panda_CAN_ChangeBaud)
- {
- auto p0 = getPanda(250);
- auto p1 = getPanda(500);
-
- p0->can_send(0xAA, FALSE, (const uint8_t*)"\x1\x2\x3\x4\x5\x6\x7\x8", 8, panda::PANDA_CAN1);
- panda_recv_loop(p0, 0);
- panda_recv_loop(p1, 0);
-
- p0->set_can_speed_kbps(panda::PANDA_CAN1, 500);
-
- auto panda_msg_recv = panda_recv_loop(p0, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0xAA, FALSE, TRUE, "\x1\x2\x3\x4\x5\x6\x7\x8", LINE_INFO());
- panda_msg_recv = panda_recv_loop(p1, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0xAA, FALSE, FALSE, "\x1\x2\x3\x4\x5\x6\x7\x8", LINE_INFO());
-
- //////////////////
-
- p0->set_can_speed_kbps(panda::PANDA_CAN1, 250);
- p0->can_send(0xC4, FALSE, (const uint8_t*)"\xA\B\xC\xD\xE\xF\x10\x11", 8, panda::PANDA_CAN1);
- panda_recv_loop(p0, 0);
- panda_recv_loop(p1, 0);
-
- p1->set_can_speed_kbps(panda::PANDA_CAN1, 250);
-
- panda_msg_recv = panda_recv_loop(p0, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0xC4, FALSE, TRUE, "\xA\B\xC\xD\xE\xF\x10\x11", LINE_INFO());
- panda_msg_recv = panda_recv_loop(p1, 1);
- check_panda_can_msg(panda_msg_recv[0], 0, 0xC4, FALSE, FALSE, "\xA\B\xC\xD\xE\xF\x10\x11", LINE_INFO());
- }
-
- TEST_METHOD(Panda_CAN_ClearClears)
- {
- auto p0 = getPanda(500, TRUE);
- p0->can_send(0xAA, FALSE, (const uint8_t*)"\x0\x1\x2\x3\x4\x5\x6\x7", 8, panda::PANDA_CAN1);
- Sleep(100);
- p0->can_clear(PANDA_CAN_RX);
-
- auto can_msgs = p0->can_recv();
- Assert::IsTrue(can_msgs.size() == 0, _T("Received messages after a clear."));
- }
- };
-
- TEST_CLASS(SerialOperations)
- {
- public:
-
- TEST_METHOD(Panda_LIN_Echo)
- {
- auto p0 = getPanda(500);
-
- for (auto lin_port : { SERIAL_LIN1, SERIAL_LIN2 }) {
- p0->serial_clear(lin_port);
-
- for (int i = 0; i < 10; i++) {
- uint8_t len = (rand() % LIN_MSG_MAX_LEN) + 1;
- std::string lindata;
- lindata.reserve(len);
-
- for (size_t j = 0; j < len; j++)
- lindata += (const char)(rand() % 256);
-
- p0->serial_write(lin_port, lindata.c_str(), len);
- Sleep(10);
-
- auto retdata = p0->serial_read(lin_port);
- Assert::AreEqual(retdata, lindata);
- }
- }
- }
- };
-}
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/stdafx.cpp b/panda/drivers/windows/pandaJ2534DLL Test/stdafx.cpp
deleted file mode 100644
index 84a1f0aaf..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/stdafx.cpp
+++ /dev/null
@@ -1,8 +0,0 @@
-// stdafx.cpp : source file that includes just the standard includes
-// pandaJ2534DLL Test.pch will be the pre-compiled header
-// stdafx.obj will contain the pre-compiled type information
-
-#include "stdafx.h"
-
-// TODO: reference any additional headers you need in STDAFX.H
-// and not in this file
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/stdafx.h b/panda/drivers/windows/pandaJ2534DLL Test/stdafx.h
deleted file mode 100644
index 1ac8bd8dc..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/stdafx.h
+++ /dev/null
@@ -1,14 +0,0 @@
-#pragma once
-
-#include "targetver.h"
-
-#define WIN32_LEAN_AND_MEAN // Exclude rarely-used stuff from Windows headers
-// Windows Header Files:
-#include
-#include
-
-// Headers for CppUnitTest
-#include "CppUnitTest.h"
-#include //Used for formatting in TestHelpers.cpp
-#include
-#include
diff --git a/panda/drivers/windows/pandaJ2534DLL Test/targetver.h b/panda/drivers/windows/pandaJ2534DLL Test/targetver.h
deleted file mode 100644
index 87c0086de..000000000
--- a/panda/drivers/windows/pandaJ2534DLL Test/targetver.h
+++ /dev/null
@@ -1,8 +0,0 @@
-#pragma once
-
-// Including SDKDDKVer.h defines the highest available Windows platform.
-
-// If you wish to build your application for a previous Windows platform, include WinSDKVer.h and
-// set the _WIN32_WINNT macro to the platform you wish to support before including SDKDDKVer.h.
-
-#include
diff --git a/panda/drivers/windows/pandaJ2534DLL/Action.h b/panda/drivers/windows/pandaJ2534DLL/Action.h
deleted file mode 100644
index e9721c2ed..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/Action.h
+++ /dev/null
@@ -1,57 +0,0 @@
-#pragma once
-#include
-
-#include "J2534Frame.h"
-
-class J2534Connection;
-
-/**
-An Action represents a unit of work that can be scheduled for execution at a later time.
-Actions are not guaranteed to be run at their specified time, but a best effort is made.
-An Action will never execute early, but can execute later depending on what is in the
-queus.
-Many different operations are based on this base class. Instead of making a thread,
-consider if the work can be offloaded to the Task Queue.
-*/
-class Action
-{
-public:
- Action(
- std::weak_ptr connection,
- std::chrono::microseconds delay
- ) : connection(connection), delay(delay) { };
-
- Action(
- std::weak_ptr connection
- ) : connection(connection), delay(std::chrono::microseconds(0)) { };
-
- //The function called by the task runner when this action is to be invoked.
- virtual void execute() = 0;
-
- //Reschedule this Action for now().
- void scheduleImmediate() {
- expire = std::chrono::steady_clock::now();
- }
-
- //Reschedule this Action relative to its last expiration time.
- void scheduleDelay() {
- expire += this->delay;
- }
-
- //Reschedule this action {delay} after now().
- void scheduleImmediateDelay() {
- expire = std::chrono::steady_clock::now() + this->delay;
- }
-
- //Reschedule this Action based on a specific base time.
- void schedule(std::chrono::time_point starttine, BOOL adddelayed) {
- this->expire = starttine;
- if (adddelayed)
- expire += this->delay;
- }
-
- std::weak_ptr connection;
- std::chrono::microseconds delay;
- //The timestamp at which point this Action is ready to be executed.
- std::chrono::time_point expire;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Connection.cpp b/panda/drivers/windows/pandaJ2534DLL/J2534Connection.cpp
deleted file mode 100644
index aa364b0f8..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Connection.cpp
+++ /dev/null
@@ -1,283 +0,0 @@
-#include "stdafx.h"
-#include "J2534Connection.h"
-#include "Timer.h"
-
-J2534Connection::J2534Connection(
- std::shared_ptr panda_dev,
- unsigned long ProtocolID,
- unsigned long Flags,
- unsigned long BaudRate
-) : panda_dev(panda_dev), ProtocolID(ProtocolID), Flags(Flags), BaudRate(BaudRate), port(0) { }
-
-unsigned long J2534Connection::validateTxMsg(PASSTHRU_MSG* msg) {
- if (msg->DataSize < this->getMinMsgLen() || msg->DataSize > this->getMaxMsgLen())
- return ERR_INVALID_MSG;
- return STATUS_NOERROR;
-}
-
-long J2534Connection::PassThruReadMsgs(PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout) {
- //Timeout of 0 means return immediately. Non zero means WAIT for that time then return. Dafuk.
- long err_code = STATUS_NOERROR;
- Timer t = Timer();
-
- unsigned long msgnum = 0;
- while (msgnum < *pNumMsgs) {
- if (Timeout > 0 && t.getTimePassed() >= Timeout) {
- err_code = ERR_TIMEOUT;
- break;
- }
-
- //Synchronized won't work where we have to break out of a loop
- messageRxBuff_mutex.lock();
- if (this->messageRxBuff.empty()) {
- messageRxBuff_mutex.unlock();
- if (Timeout == 0)
- break;
- Sleep(2);
- continue;
- }
-
- auto msg_in = this->messageRxBuff.front();
- this->messageRxBuff.pop();
- messageRxBuff_mutex.unlock();
-
- PASSTHRU_MSG *msg_out = &pMsg[msgnum++];
- msg_out->ProtocolID = this->ProtocolID;
- msg_out->DataSize = msg_in.Data.size();
- memcpy(msg_out->Data, msg_in.Data.c_str(), msg_in.Data.size());
- msg_out->Timestamp = msg_in.Timestamp;
- msg_out->RxStatus = msg_in.RxStatus;
- msg_out->ExtraDataIndex = msg_in.ExtraDataIndex;
- msg_out->TxFlags = 0;
- if (msgnum == *pNumMsgs) break;
- }
-
- if (msgnum == 0)
- err_code = ERR_BUFFER_EMPTY;
- *pNumMsgs = msgnum;
- return err_code;
-}
-
-long J2534Connection::PassThruWriteMsgs(PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout) {
- //There doesn't seem to be much reason to implement the timeout here.
- for (int msgnum = 0; msgnum < *pNumMsgs; msgnum++) {
- PASSTHRU_MSG* msg = &pMsg[msgnum];
- if (msg->ProtocolID != this->ProtocolID) {
- *pNumMsgs = msgnum;
- return ERR_MSG_PROTOCOL_ID;
- }
-
- auto retcode = this->validateTxMsg(msg);
- if (retcode != STATUS_NOERROR) {
- *pNumMsgs = msgnum;
- return retcode;
- }
-
- auto msgtx = this->parseMessageTx(*pMsg);
- if (msgtx != nullptr) //Nullptr is supported for unimplemented connection types.
- this->schedultMsgTx(std::dynamic_pointer_cast(msgtx));
- }
- return STATUS_NOERROR;
-}
-
-//The docs say that a device has to support 10 periodic messages, though more is ok.
-//It is easier to store them on the connection, so 10 per connection it is.
-long J2534Connection::PassThruStartPeriodicMsg(PASSTHRU_MSG *pMsg, unsigned long *pMsgID, unsigned long TimeInterval) {
- if (pMsg->DataSize < getMinMsgLen() || pMsg->DataSize > getMaxMsgSingleFrameLen()) return ERR_INVALID_MSG;
- if (pMsg->ProtocolID != this->ProtocolID) return ERR_MSG_PROTOCOL_ID;
- if (TimeInterval < 5 || TimeInterval > 65535) return ERR_INVALID_TIME_INTERVAL;
-
- for (int i = 0; i < this->periodicMessages.size(); i++) {
- if (periodicMessages[i] != nullptr) continue;
-
- *pMsgID = i;
- auto msgtx = this->parseMessageTx(*pMsg);
- if (msgtx != nullptr) {
- periodicMessages[i] = std::make_shared(std::chrono::microseconds(TimeInterval*1000), msgtx);
- periodicMessages[i]->scheduleImmediate();
- if (auto panda_dev = this->getPandaDev()) {
- panda_dev->insertActionIntoTaskList(periodicMessages[i]);
- }
- }
- return STATUS_NOERROR;
- }
- return ERR_EXCEEDED_LIMIT;
-}
-
-long J2534Connection::PassThruStopPeriodicMsg(unsigned long MsgID) {
- if (MsgID >= this->periodicMessages.size() || this->periodicMessages[MsgID] == nullptr)
- return ERR_INVALID_MSG_ID;
- this->periodicMessages[MsgID]->cancel();
- this->periodicMessages[MsgID] = nullptr;
- return STATUS_NOERROR;
-}
-
-long J2534Connection::PassThruStartMsgFilter(unsigned long FilterType, PASSTHRU_MSG *pMaskMsg, PASSTHRU_MSG *pPatternMsg,
- PASSTHRU_MSG *pFlowControlMsg, unsigned long *pFilterID) {
- for (int i = 0; i < this->filters.size(); i++) {
- if (filters[i] == nullptr) {
- try {
- auto newfilter = std::make_shared(this, FilterType, pMaskMsg, pPatternMsg, pFlowControlMsg);
- for (int check_idx = 0; check_idx < filters.size(); check_idx++) {
- if (filters[check_idx] == nullptr) continue;
- if (filters[check_idx] == newfilter) {
- filters[i] = nullptr;
- return ERR_NOT_UNIQUE;
- }
- }
- *pFilterID = i;
- filters[i] = newfilter;
- return STATUS_NOERROR;
- } catch (int e) {
- return e;
- }
- }
- }
- return ERR_EXCEEDED_LIMIT;
-}
-
-long J2534Connection::PassThruStopMsgFilter(unsigned long FilterID) {
- if (FilterID >= this->filters.size() || this->filters[FilterID] == nullptr)
- return ERR_INVALID_FILTER_ID;
- this->filters[FilterID] = nullptr;
- return STATUS_NOERROR;
-}
-
-long J2534Connection::PassThruIoctl(unsigned long IoctlID, void *pInput, void *pOutput) {
- return STATUS_NOERROR;
-}
-
-long J2534Connection::init5b(SBYTE_ARRAY* pInput, SBYTE_ARRAY* pOutput) { return ERR_FAILED; }
-long J2534Connection::initFast(PASSTHRU_MSG* pInput, PASSTHRU_MSG* pOutput) { return ERR_FAILED; }
-long J2534Connection::clearTXBuff() {
- if (auto panda_ps = this->panda_dev.lock()) {
- synchronized(staged_writes_lock) {
- this->txbuff = {};
- panda_ps->panda->can_clear(panda::PANDA_CAN1_TX);
- }
- }
- return STATUS_NOERROR;
-}
-long J2534Connection::clearRXBuff() {
- if (auto panda_ps = this->panda_dev.lock()) {
- synchronized(messageRxBuff_mutex) {
- this->messageRxBuff = {};
- panda_ps->panda->can_clear(panda::PANDA_CAN_RX);
- }
- }
- return STATUS_NOERROR;
-}
-long J2534Connection::clearPeriodicMsgs() {
- for (int i = 0; i < this->periodicMessages.size(); i++) {
- if (periodicMessages[i] == nullptr) continue;
- this->periodicMessages[i]->cancel();
- this->periodicMessages[i] = nullptr;
- }
-
- return STATUS_NOERROR;
-}
-long J2534Connection::clearMsgFilters() {
- for (auto& filter : this->filters) filter = nullptr;
- return STATUS_NOERROR;
-}
-
-void J2534Connection::setBaud(unsigned long baud) {
- this->BaudRate = baud;
-}
-
-void J2534Connection::schedultMsgTx(std::shared_ptr msgout) {
- if (auto panda_ps = this->panda_dev.lock()) {
- synchronized(staged_writes_lock) {
- this->txbuff.push(msgout);
- panda_ps->registerConnectionTx(shared_from_this());
- }
- }
-}
-
-void J2534Connection::rescheduleExistingTxMsgs() {
- if (auto panda_ps = this->panda_dev.lock()) {
- synchronized(staged_writes_lock) {
- panda_ps->unstallConnectionTx(shared_from_this());
- }
- }
-}
-
-//Works well as long as the protocol doesn't support flow control.
-void J2534Connection::processMessage(const J2534Frame& msg) {
- FILTER_RESULT filter_res = FILTER_RESULT_NEUTRAL;
-
- for (auto filter : this->filters) {
- if (filter == nullptr) continue;
- FILTER_RESULT current_check_res = filter->check(msg);
- if (current_check_res == FILTER_RESULT_BLOCK) return;
- if (current_check_res == FILTER_RESULT_PASS) filter_res = FILTER_RESULT_PASS;
- }
-
- if (filter_res == FILTER_RESULT_PASS) {
- addMsgToRxQueue(msg);
- }
-}
-
-void J2534Connection::processIOCTLSetConfig(unsigned long Parameter, unsigned long Value) {
- switch (Parameter) {
- case DATA_RATE: // 5-500000
- this->setBaud(Value);
- break;
- case LOOPBACK: // 0 (OFF), 1 (ON) [0]
- this->loopback = (Value != 0);
- break;
- case ISO15765_WFT_MAX:
- break;
- case NODE_ADDRESS: // J1850PWM Related (Not supported by panda). HDS requires these to 'work'.
- case NETWORK_LINE:
- case P1_MIN: // A bunch of stuff relating to ISO9141 and ISO14230 that the panda
- case P1_MAX: // currently doesn't support. Don't let HDS know we can't use these.
- case P2_MIN:
- case P2_MAX:
- case P3_MIN:
- case P3_MAX:
- case P4_MIN:
- case P4_MAX:
- case W0:
- case W1:
- case W2:
- case W3:
- case W4:
- case W5:
- case TIDLE:
- case TINIL:
- case TWUP:
- case PARITY:
- case T1_MAX: // SCI related options. The panda does not appear to support this
- case T2_MAX:
- case T3_MAX:
- case T4_MAX:
- case T5_MAX:
- break; // Just smile and nod.
- default:
- printf("Got unknown SET code %X\n", Parameter);
- }
-
- // reserved parameters usually mean special equiptment is required
- if (Parameter >= 0x20) {
- throw ERR_NOT_SUPPORTED;
- }
-}
-
-unsigned long J2534Connection::processIOCTLGetConfig(unsigned long Parameter) {
- switch (Parameter) {
- case DATA_RATE:
- return this->getBaud();
- case LOOPBACK:
- return this->loopback;
- break;
- case BIT_SAMPLE_POINT:
- return 80;
- case SYNC_JUMP_WIDTH:
- return 15;
- default:
- // HDS rarely reads off values through ioctl GET_CONFIG, but it often
- // just wants the call to pass without erroring, so just don't do anything.
- printf("Got unknown code %X\n", Parameter);
- }
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Connection.h b/panda/drivers/windows/pandaJ2534DLL/J2534Connection.h
deleted file mode 100644
index 70f25a106..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Connection.h
+++ /dev/null
@@ -1,141 +0,0 @@
-#pragma once
-#include "panda_shared/panda.h"
-#include "J2534_v0404.h"
-#include "synchronize.h"
-#include "J2534Frame.h"
-#include "PandaJ2534Device.h"
-#include "J2534MessageFilter.h"
-#include "MessagePeriodic.h"
-
-class J2534Frame;
-class Action;
-class PandaJ2534Device;
-class J2534MessageFilter;
-
-#define check_bmask(num, mask)(((num) & mask) == mask)
-
-/**
-Class representing a generic J2534 Connection created by PassThruConnect,
-and is associated with a channelID given to the J2534 API user.
-Subclasses implement specific J2534 supported protocols.
-*/
-class J2534Connection : public std::enable_shared_from_this {
- friend class PandaJ2534Device;
-
-public:
- J2534Connection(
- std::shared_ptr panda_dev,
- unsigned long ProtocolID,
- unsigned long Flags,
- unsigned long BaudRate
- );
- virtual ~J2534Connection() {};
-
- //J2534 API functions
-
- virtual long PassThruReadMsgs(PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout);
- long PassThruWriteMsgs(PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout);
- virtual long PassThruStartPeriodicMsg(PASSTHRU_MSG *pMsg, unsigned long *pMsgID, unsigned long TimeInterval);
- virtual long PassThruStopPeriodicMsg(unsigned long MsgID);
-
- virtual long PassThruStartMsgFilter(unsigned long FilterType, PASSTHRU_MSG *pMaskMsg, PASSTHRU_MSG *pPatternMsg,
- PASSTHRU_MSG *pFlowControlMsg, unsigned long *pFilterID);
-
- virtual long PassThruStopMsgFilter(unsigned long FilterID);
- virtual long PassThruIoctl(unsigned long IoctlID, void *pInput, void *pOutput);
-
- //Functions for parsing messages to be send with PassThruWriteMsgs.
-
- virtual unsigned long validateTxMsg(PASSTHRU_MSG* msg);
- virtual std::shared_ptr parseMessageTx(PASSTHRU_MSG& msg) { return nullptr; };
-
- //IOCTL functions
-
- long init5b(SBYTE_ARRAY* pInput, SBYTE_ARRAY* pOutput);
- long initFast(PASSTHRU_MSG* pInput, PASSTHRU_MSG* pOutput);
- long clearTXBuff();
- long clearRXBuff();
- long clearPeriodicMsgs();
- long clearMsgFilters();
-
- virtual void setBaud(unsigned long baud);
-
- unsigned long getBaud() {
- return this->BaudRate;
- }
-
- unsigned long getProtocol() {
- return this->ProtocolID;
- };
-
- virtual bool isProtoCan() {
- return FALSE;
- }
-
- //Port is used in a protocol specific way to differentiate tranceivers.
- unsigned long getPort() {
- return this->port;
- }
-
- virtual void processIOCTLSetConfig(unsigned long Parameter, unsigned long Value);
-
- virtual unsigned long processIOCTLGetConfig(unsigned long Parameter);
-
- //Called when the passthru device has received a message for this connection
- //Loopback messages are processed separately.
- virtual void processMessage(const J2534Frame& msg);
-
- //Limitations on message size. Override in every subclass.
-
- virtual unsigned long getMinMsgLen() {
- return 1;
- }
-
- virtual unsigned long getMaxMsgLen() {
- return 4128;
- }
-
- virtual unsigned long getMaxMsgSingleFrameLen() {
- return 12;
- }
-
- //Add an Action to the Task Queue for future processing.
- //The task should be set its expire time before being submitted.
- void schedultMsgTx(std::shared_ptr msgout);
-
- void rescheduleExistingTxMsgs();
-
- std::shared_ptr getPandaDev() {
- if (auto panda_dev_sp = this->panda_dev.lock())
- return panda_dev_sp;
- return nullptr;
- }
-
- //Add a message to the queue read by PassThruReadMsgs().
- void addMsgToRxQueue(const J2534Frame& frame) {
- synchronized(messageRxBuff_mutex) {
- messageRxBuff.push(frame);
- }
- }
-
- bool loopback = FALSE;
-
-protected:
- unsigned long ProtocolID;
- unsigned long Flags;
- unsigned long BaudRate;
- unsigned long port;
-
- std::weak_ptr panda_dev;
-
- Mutex messageRxBuff_mutex;
- std::queue messageRxBuff;
-
- std::array, 10> filters;
- std::queue> txbuff;
-
- std::array, 10> periodicMessages;
-
-private:
- Mutex staged_writes_lock;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_CAN.cpp b/panda/drivers/windows/pandaJ2534DLL/J2534Connection_CAN.cpp
deleted file mode 100644
index 342616900..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_CAN.cpp
+++ /dev/null
@@ -1,41 +0,0 @@
-#include "stdafx.h"
-#include "J2534Connection_CAN.h"
-#include "MessageTx_CAN.h"
-#include "Timer.h"
-
-J2534Connection_CAN::J2534Connection_CAN(
- std::shared_ptr panda_dev,
- unsigned long ProtocolID,
- unsigned long Flags,
- unsigned long BaudRate
- ) : J2534Connection(panda_dev, ProtocolID, Flags, BaudRate) {
- this->port = 0;
-
- if (BaudRate % 100 || BaudRate < 10000 || BaudRate > 5000000)
- throw ERR_INVALID_BAUDRATE;
-
- panda_dev->panda->set_can_speed_cbps(panda::PANDA_CAN1, BaudRate/100);
-};
-
-unsigned long J2534Connection_CAN::validateTxMsg(PASSTHRU_MSG* msg) {
- if ((msg->DataSize < this->getMinMsgLen() || msg->DataSize > this->getMaxMsgLen() ||
- (val_is_29bit(msg->TxFlags) != this->_is_29bit() && !check_bmask(this->Flags, CAN_ID_BOTH))))
- return ERR_INVALID_MSG;
- return STATUS_NOERROR;
-}
-
-std::shared_ptr J2534Connection_CAN::parseMessageTx(PASSTHRU_MSG& msg) {
- return std::dynamic_pointer_cast(std::make_shared(shared_from_this(), msg));
-}
-
-void J2534Connection_CAN::setBaud(unsigned long BaudRate) {
- if (auto panda_dev = this->getPandaDev()) {
- if (BaudRate % 100 || BaudRate < 10000 || BaudRate > 5000000)
- throw ERR_NOT_SUPPORTED;
-
- panda_dev->panda->set_can_speed_cbps(panda::PANDA_CAN1, (uint16_t)(BaudRate / 100));
- return J2534Connection::setBaud(BaudRate);
- } else {
- throw ERR_DEVICE_NOT_CONNECTED;
- }
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_CAN.h b/panda/drivers/windows/pandaJ2534DLL/J2534Connection_CAN.h
deleted file mode 100644
index 3971351ee..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_CAN.h
+++ /dev/null
@@ -1,43 +0,0 @@
-#pragma once
-
-#include "J2534Connection.h"
-#include "panda_shared/panda.h"
-
-#define val_is_29bit(num) check_bmask(num, CAN_29BIT_ID)
-
-class J2534Connection_CAN : public J2534Connection {
-public:
- J2534Connection_CAN(
- std::shared_ptr panda_dev,
- unsigned long ProtocolID,
- unsigned long Flags,
- unsigned long BaudRate
- );
-
- virtual unsigned long validateTxMsg(PASSTHRU_MSG* msg);
-
- virtual std::shared_ptr parseMessageTx(PASSTHRU_MSG& pMsg);
-
- virtual void setBaud(unsigned long baud);
-
- virtual unsigned long getMinMsgLen() {
- return 4;
- }
-
- virtual unsigned long getMaxMsgLen() {
- return 12;
- }
-
- virtual unsigned long getMaxMsgSingleFrameLen() {
- return 12;
- }
-
- virtual bool isProtoCan() {
- return TRUE;
- }
-
- bool _is_29bit() {
- return (this->Flags & CAN_29BIT_ID) == CAN_29BIT_ID;
- }
-
-};
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_ISO15765.cpp b/panda/drivers/windows/pandaJ2534DLL/J2534Connection_ISO15765.cpp
deleted file mode 100644
index a83f6f433..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_ISO15765.cpp
+++ /dev/null
@@ -1,232 +0,0 @@
-#include "stdafx.h"
-#include "J2534Connection_ISO15765.h"
-#include "Timer.h"
-#include "constants_ISO15765.h"
-#include
-
-J2534Connection_ISO15765::J2534Connection_ISO15765(
- std::shared_ptr panda_dev,
- unsigned long ProtocolID,
- unsigned long Flags,
- unsigned long BaudRate
-) : J2534Connection(panda_dev, ProtocolID, Flags, BaudRate), wftMax(0) {
- this->port = 0;
-
- if (BaudRate % 100 || BaudRate < 10000 || BaudRate > 5000000)
- throw ERR_INVALID_BAUDRATE;
-
- panda_dev->panda->set_can_speed_cbps(panda::PANDA_CAN1, (uint16_t)(BaudRate / 100));
-}
-
-unsigned long J2534Connection_ISO15765::validateTxMsg(PASSTHRU_MSG* msg) {
- if ((msg->DataSize < this->getMinMsgLen() + (msg_is_extaddr(msg) ? 1 : 0) ||
- msg->DataSize > this->getMaxMsgLen() + (msg_is_extaddr(msg) ? 1 : 0) ||
- (val_is_29bit(msg->TxFlags) != this->_is_29bit() && !check_bmask(this->Flags, CAN_ID_BOTH))))
- return ERR_INVALID_MSG;
-
- int fid = get_matching_out_fc_filter_id(std::string((const char*)msg->Data, msg->DataSize), msg->TxFlags, 0xFFFFFFFF);
- if (msg->DataSize > getMaxMsgSingleFrameLen() && fid == -1) return ERR_NO_FLOW_CONTROL; //11 bytes (4 for CANid, 7 payload) is max length of input frame.
-
- return STATUS_NOERROR;
-}
-
-std::shared_ptr J2534Connection_ISO15765::parseMessageTx(PASSTHRU_MSG& msg) {
- int fid = get_matching_out_fc_filter_id(std::string((const char*)msg.Data, msg.DataSize), msg.TxFlags, 0xFFFFFFFF);
- if (msg.DataSize > getMaxMsgSingleFrameLen() && fid == -1) 1;
-
- return std::dynamic_pointer_cast(
- std::make_shared(shared_from_this(), msg, (fid == -1) ? nullptr : this->filters[fid])
- );
-}
-
-//https://happilyembedded.wordpress.com/2016/02/15/can-multiple-frame-transmission/
-void J2534Connection_ISO15765::processMessage(const J2534Frame& msg) {
- if (msg.ProtocolID != CAN) return;
-
- int fid = get_matching_in_fc_filter_id(msg, this->Flags);
- if (fid == -1) return;
-
- auto filter = this->filters[fid];
- bool is_ext_addr = check_bmask(filter->flags, ISO15765_ADDR_TYPE);
- uint8_t addrlen = is_ext_addr ? 5 : 4;
-
- switch (msg_get_type(msg, addrlen)) {
- case FRAME_FLOWCTRL:
- {
- if (this->txbuff.size() == 0)
- return;
- if (msg.Data.size() < addrlen + 3) return;
- uint8_t flow_status = msg.Data[addrlen] & 0x0F;
- uint8_t block_size = msg.Data[addrlen + 1];
- uint8_t st_min = msg.Data[addrlen + 2];
-
- auto txConvo = std::static_pointer_cast(this->txbuff.front());
- switch (flow_status) {
- case FLOWCTRL_CONTINUE: {
- if (st_min > 0xF9) break;
- if (st_min >= 0xf1 && st_min <= 0xf9) {
- txConvo->flowControlContinue(block_size, std::chrono::microseconds((st_min & 0x0F) * 100));
- } else if(st_min <= 0x7f) {
- txConvo->flowControlContinue(block_size, std::chrono::microseconds(st_min * 1000));
- } else {
- break;
- }
- txConvo->scheduleImmediate();
- this->rescheduleExistingTxMsgs();
- break;
- }
- case FLOWCTRL_WAIT:
- txConvo->flowControlWait(this->wftMax);
- break;
- case FLOWCTRL_ABORT:
- txConvo->flowControlAbort();
- break;
- }
- break;
- }
- case FRAME_SINGLE:
- {
- this->rxConversations[fid] = nullptr; //Reset any current transaction.
-
- if (is_ext_addr) {
- if ((msg.Data[5] & 0x0F) > 6) return;
- } else {
- if ((msg.Data[4] & 0x0F) > 7) return;
- }
-
- J2534Frame outframe(ISO15765, msg.RxStatus, 0, msg.Timestamp);
- if (msg.Data.size() != 8 && check_bmask(this->Flags, ISO15765_FRAME_PAD))
- outframe.RxStatus |= ISO15765_PADDING_ERROR;
- if (is_ext_addr)
- outframe.RxStatus |= ISO15765_ADDR_TYPE;
- outframe.Data = msg.Data.substr(0, addrlen) + msg.Data.substr(addrlen + 1, msg.Data[addrlen]);
- outframe.ExtraDataIndex = outframe.Data.size();
-
- addMsgToRxQueue(outframe);
- break;
- }
- case FRAME_FIRST:
- {
- if (msg.Data.size() < 12) {
- //A frame was received that could have held more data.
- //No examples of this protocol show that happening, so
- //it will be assumed that it is grounds to reset rx.
- this->rxConversations[fid] = nullptr;
- return;
- }
-
- J2534Frame outframe(ISO15765, msg.RxStatus | START_OF_MESSAGE, 0, msg.Timestamp);
- if (is_ext_addr)
- outframe.RxStatus |= ISO15765_ADDR_TYPE;
- outframe.Data = msg.Data.substr(0, addrlen);
-
- addMsgToRxQueue(outframe);
-
- this->rxConversations[fid] = std::make_shared(
- ((msg.Data[addrlen] & 0x0F) << 8) | msg.Data[addrlen + 1],
- msg.Data.substr(addrlen + 2, 12 - (addrlen + 2)),
- msg.RxStatus, filter);
-
- //TODO maybe the flow control should also be scheduled in the TX list.
- //Doing it this way because the filter can be 5 bytes in ext address mode.
- std::string flowfilter = filter->get_flowctrl();
- uint32_t flow_addr = (((uint8_t)flowfilter[0]) << 24) | ((uint8_t)(flowfilter[1]) << 16) | ((uint8_t)(flowfilter[2]) << 8) | ((uint8_t)flowfilter[3]);
-
- std::string flowstrlresp;
- if (flowfilter.size() > 4)
- flowstrlresp += flowfilter[4];
- flowstrlresp += std::string("\x30\x00\x00", 3);
- if (check_bmask(filter->flags, ISO15765_FRAME_PAD)) {
- flowstrlresp += std::string(8 - flowstrlresp.size(), '\x00');
- }
-
- if (auto panda_dev_sp = this->panda_dev.lock()) {
- panda_dev_sp->panda->can_send(flow_addr, val_is_29bit(msg.RxStatus), (const uint8_t *)flowstrlresp.c_str(), (uint8_t)flowstrlresp.size(), panda::PANDA_CAN1);
- }
- break;
- }
- case FRAME_CONSEC:
- {
- auto& convo = this->rxConversations[fid];
- if (convo == nullptr) return;
-
- if (!convo->rx_add_frame(msg.Data[addrlen], (is_ext_addr ? 6 : 7), msg.Data.substr(addrlen + 1))) {
- //Delete this conversation.
- convo = nullptr;
- return;
- }
-
- std::string final_msg;
- if (convo->flush_result(final_msg)) {
- convo = nullptr;
- J2534Frame outframe(ISO15765, msg.RxStatus, 0, msg.Timestamp);
- if (is_ext_addr)
- outframe.RxStatus |= ISO15765_ADDR_TYPE;
- outframe.Data = msg.Data.substr(0, addrlen) + final_msg;
- outframe.ExtraDataIndex = outframe.Data.size();
-
- addMsgToRxQueue(outframe);
- }
- break;
- }
- }
-}
-
-void J2534Connection_ISO15765::setBaud(unsigned long BaudRate) {
- if (auto panda_dev = this->getPandaDev()) {
- if (BaudRate % 100 || BaudRate < 10000 || BaudRate > 5000000)
- throw ERR_NOT_SUPPORTED;
-
- panda_dev->panda->set_can_speed_cbps(panda::PANDA_CAN1, (uint16_t)(BaudRate / 100));
- return J2534Connection::setBaud(BaudRate);
- } else {
- throw ERR_DEVICE_NOT_CONNECTED;
- }
-}
-
-long J2534Connection_ISO15765::PassThruStartMsgFilter(unsigned long FilterType, PASSTHRU_MSG *pMaskMsg, PASSTHRU_MSG *pPatternMsg,
- PASSTHRU_MSG *pFlowControlMsg, unsigned long *pFilterID) {
-
- if (FilterType != FLOW_CONTROL_FILTER) return ERR_INVALID_FILTER_ID;
- return J2534Connection::PassThruStartMsgFilter(FilterType, pMaskMsg, pPatternMsg, pFlowControlMsg, pFilterID);
-}
-
-int J2534Connection_ISO15765::get_matching_out_fc_filter_id(const std::string& msgdata, unsigned long flags, unsigned long flagmask) {
- for (unsigned int i = 0; i < this->filters.size(); i++) {
- if (this->filters[i] == nullptr) continue;
- auto filter = this->filters[i]->get_flowctrl();
- if (filter == msgdata.substr(0, filter.size()) &&
- (this->filters[i]->flags & flagmask) == (flags & flagmask))
- return i;
- }
- return -1;
-}
-
-int J2534Connection_ISO15765::get_matching_in_fc_filter_id(const J2534Frame& msg, unsigned long flagmask) {
- for (unsigned int i = 0; i < this->filters.size(); i++) {
- if (this->filters[i] == nullptr) continue;
- if (this->filters[i]->check(msg) == FILTER_RESULT_MATCH &&
- (this->filters[i]->flags & flagmask) == (msg.RxStatus & flagmask))
- return i;
- }
- return -1;
-}
-
-void J2534Connection_ISO15765::processIOCTLSetConfig(unsigned long Parameter, unsigned long Value) {
- switch (Parameter) {
- case ISO15765_WFT_MAX:
- this->wftMax = Value;
- break;
- default:
- J2534Connection::processIOCTLSetConfig(Parameter, Value);
- }
-}
-
-unsigned long J2534Connection_ISO15765::processIOCTLGetConfig(unsigned long Parameter) {
- switch (Parameter) {
- case ISO15765_WFT_MAX:
- return this->wftMax;
- default:
- return J2534Connection::processIOCTLGetConfig(Parameter);
- }
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_ISO15765.h b/panda/drivers/windows/pandaJ2534DLL/J2534Connection_ISO15765.h
deleted file mode 100644
index beb9f012e..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Connection_ISO15765.h
+++ /dev/null
@@ -1,65 +0,0 @@
-#pragma once
-#include
-#include "J2534Connection.h"
-#include "J2534Connection_CAN.h"
-#include "MessageTx_ISO15765.h"
-#include "MessageRx.h"
-
-class MessageTx_ISO15765;
-
-typedef struct {
- std::string dispatched_msg;
- std::string remaining_payload;
-} PRESTAGED_WRITE;
-
-class J2534Connection_ISO15765 : public J2534Connection {
-public:
- J2534Connection_ISO15765(
- std::shared_ptr panda_dev,
- unsigned long ProtocolID,
- unsigned long Flags,
- unsigned long BaudRate
- );
-
- virtual long PassThruStartMsgFilter(unsigned long FilterType, PASSTHRU_MSG * pMaskMsg, PASSTHRU_MSG * pPatternMsg, PASSTHRU_MSG * pFlowControlMsg, unsigned long * pFilterID);
-
- int get_matching_out_fc_filter_id(const std::string & msgdata, unsigned long flags, unsigned long flagmask);
-
- int get_matching_in_fc_filter_id(const J2534Frame& msg, unsigned long flagmask);
-
- virtual unsigned long validateTxMsg(PASSTHRU_MSG* msg);
-
- virtual std::shared_ptr parseMessageTx(PASSTHRU_MSG& msg);
-
- virtual void processMessage(const J2534Frame& msg);
-
- virtual void setBaud(unsigned long baud);
-
- virtual void processIOCTLSetConfig(unsigned long Parameter, unsigned long Value);
-
- virtual unsigned long processIOCTLGetConfig(unsigned long Parameter);
-
- virtual unsigned long getMinMsgLen() {
- return 4;
- }
-
- virtual unsigned long getMaxMsgLen() {
- return 4099;
- };
-
- virtual unsigned long getMaxMsgSingleFrameLen() {
- return 11;
- }
-
- virtual bool _is_29bit() {
- return (this->Flags & CAN_29BIT_ID) == CAN_29BIT_ID;
- }
-
- virtual bool isProtoCan() {
- return TRUE;
- }
-
-private:
- std::array, 10> rxConversations;
- unsigned int wftMax;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534Frame.h b/panda/drivers/windows/pandaJ2534DLL/J2534Frame.h
deleted file mode 100644
index 2549216b6..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534Frame.h
+++ /dev/null
@@ -1,48 +0,0 @@
-#pragma once
-#include "J2534_v0404.h"
-#include "panda_shared/panda.h"
-
-/*A move convenient container for J2534 Messages than the static buffer provided by default.*/
-class J2534Frame {
-public:
- J2534Frame(unsigned long ProtocolID, unsigned long RxStatus=0, unsigned long TxFlags=0, unsigned long Timestamp=0) :
- ProtocolID(ProtocolID), RxStatus(RxStatus), TxFlags(TxFlags), Timestamp(Timestamp), ExtraDataIndex(0), Data("") { };
-
- J2534Frame(const panda::PANDA_CAN_MSG& msg_in) {
- ProtocolID = CAN;
- ExtraDataIndex = msg_in.len + 4;
- Data.reserve(msg_in.len + 4);
- Data += msg_in.addr >> 24;
- Data += (msg_in.addr >> 16) & 0xFF;
- Data += (msg_in.addr >> 8) & 0xFF;
- Data += msg_in.addr & 0xFF;
- Data += std::string((char*)&msg_in.dat, msg_in.len);
- Timestamp = msg_in.recv_time;
- RxStatus = (msg_in.addr_29b ? CAN_29BIT_ID : 0) |
- (msg_in.is_receipt ? TX_MSG_TYPE : 0);
- }
-
- J2534Frame(const PASSTHRU_MSG& msg) {
- this->ProtocolID = msg.ProtocolID;
- this->RxStatus = msg.RxStatus;
- this->TxFlags = msg.TxFlags;
- this->Timestamp = msg.Timestamp;
- this->ExtraDataIndex = msg.ExtraDataIndex;
- this->Data = std::string((const char*)msg.Data, msg.DataSize);
- }
-
- J2534Frame() {
- this->ProtocolID = 0;
- this->RxStatus = 0;
- this->TxFlags = 0;
- this->Timestamp = 0;
- this->ExtraDataIndex = 0;
- }
-
- unsigned long ProtocolID;
- unsigned long RxStatus;
- unsigned long TxFlags;
- unsigned long Timestamp;
- unsigned long ExtraDataIndex;
- std::string Data;
-};
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534MessageFilter.cpp b/panda/drivers/windows/pandaJ2534DLL/J2534MessageFilter.cpp
deleted file mode 100644
index 2d19e1f4e..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534MessageFilter.cpp
+++ /dev/null
@@ -1,104 +0,0 @@
-#include "stdafx.h"
-#include "J2534MessageFilter.h"
-#include "J2534Frame.h"
-
-J2534MessageFilter::J2534MessageFilter(
- J2534Connection *const conn,
- unsigned int filtertype,
- PASSTHRU_MSG *pMaskMsg,
- PASSTHRU_MSG *pPatternMsg,
- PASSTHRU_MSG *pFlowControlMsg
-) : filtertype(filtertype), flags(0), conn(conn) {
- switch (filtertype) {
- case PASS_FILTER:
- case BLOCK_FILTER:
- if (pMaskMsg == NULL || pPatternMsg == NULL)
- throw ERR_NULL_PARAMETER;
- if (pFlowControlMsg != NULL)
- throw ERR_INVALID_FILTER_ID;
- if (pMaskMsg->DataSize != pPatternMsg->DataSize)
- throw ERR_INVALID_MSG;
- break;
- case FLOW_CONTROL_FILTER:
- if (conn->getProtocol() != ISO15765) throw ERR_MSG_PROTOCOL_ID; //CHECK
- if (pFlowControlMsg == NULL || pMaskMsg == NULL || pPatternMsg == NULL)
- throw ERR_NULL_PARAMETER;
- break;
- default:
- throw ERR_INVALID_MSG;
- }
-
- if (!(conn->getMinMsgLen() < pMaskMsg->DataSize || pMaskMsg->DataSize < conn->getMaxMsgLen()))
- throw ERR_INVALID_MSG;
- if (conn->getProtocol() != pMaskMsg->ProtocolID)
- throw ERR_MSG_PROTOCOL_ID;
- this->maskMsg = std::string((char*)pMaskMsg->Data, pMaskMsg->DataSize);
-
- if (!(conn->getMinMsgLen() < pPatternMsg->DataSize || pPatternMsg->DataSize < conn->getMaxMsgLen()))
- throw ERR_INVALID_MSG;
- if (conn->getProtocol() != pPatternMsg->ProtocolID)
- throw ERR_MSG_PROTOCOL_ID;
- this->patternMsg = std::string((char*)pPatternMsg->Data, pPatternMsg->DataSize);
- if (this->maskMsg.size() != this->patternMsg.size())
- throw ERR_INVALID_MSG;
-
- if (pFlowControlMsg) {
- if (!(conn->getMinMsgLen() < pFlowControlMsg->DataSize || pFlowControlMsg->DataSize < conn->getMaxMsgLen()))
- throw ERR_INVALID_MSG;
- if (conn->getProtocol() != pFlowControlMsg->ProtocolID)
- throw ERR_MSG_PROTOCOL_ID;
- if (pMaskMsg->TxFlags != pPatternMsg->TxFlags || pMaskMsg->TxFlags != pFlowControlMsg->TxFlags)
- throw ERR_INVALID_MSG;
- if(pFlowControlMsg->TxFlags & ~(ISO15765_FRAME_PAD | CAN_29BIT_ID | ISO15765_ADDR_TYPE))
- throw ERR_INVALID_MSG;
- if ((pFlowControlMsg->TxFlags & ISO15765_ADDR_TYPE) == ISO15765_ADDR_TYPE) {
- if(pFlowControlMsg->DataSize != 5)
- throw ERR_INVALID_MSG;
- } else {
- if (pFlowControlMsg->DataSize != 4)
- throw ERR_INVALID_MSG;
- }
- this->flowCtrlMsg = std::string((char*)pFlowControlMsg->Data, pFlowControlMsg->DataSize);
- if (this->flowCtrlMsg.size() != this->patternMsg.size())
- throw ERR_INVALID_MSG;
- this->flags = pFlowControlMsg->TxFlags;
- }
-}
-
-bool J2534MessageFilter::operator ==(const J2534MessageFilter &b) const {
- if (this->filtertype != b.filtertype) return FALSE;
- if (this->maskMsg != b.maskMsg) return FALSE;
- if (this->patternMsg != b.patternMsg) return FALSE;
- if (this->flowCtrlMsg != b.flowCtrlMsg) return FALSE;
- if (this->flags != b.flags) return FALSE;
- return TRUE;
-}
-
-FILTER_RESULT J2534MessageFilter::check(const J2534Frame& msg) {
- bool matches = TRUE;
- if (msg.Data.size() < this->maskMsg.size()) {
- matches = FALSE;
- } else {
- for (int i = 0; i < this->maskMsg.size(); i++) {
- if (this->patternMsg[i] != (msg.Data[i] & this->maskMsg[i])) {
- matches = FALSE;
- break;
- }
- }
- }
-
- switch (this->filtertype) {
- case PASS_FILTER:
- return matches ? FILTER_RESULT_PASS : FILTER_RESULT_NEUTRAL;
- case BLOCK_FILTER:
- return matches ? FILTER_RESULT_BLOCK: FILTER_RESULT_NEUTRAL;
- case FLOW_CONTROL_FILTER:
- return matches ? FILTER_RESULT_MATCH : FILTER_RESULT_NOMATCH;
- default:
- throw std::out_of_range("Filtertype should not be able to be anything but PASS, BLOCK, or FLOW_CONTROL");
- }
-}
-
-std::string J2534MessageFilter::get_flowctrl() {
- return std::string(this->flowCtrlMsg);
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534MessageFilter.h b/panda/drivers/windows/pandaJ2534DLL/J2534MessageFilter.h
deleted file mode 100644
index c5e9a6839..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534MessageFilter.h
+++ /dev/null
@@ -1,47 +0,0 @@
-#pragma once
-#include "J2534_v0404.h"
-#include "J2534Connection.h"
-#include "J2534Frame.h"
-
-typedef enum {
- FILTER_RESULT_BLOCK,
- FILTER_RESULT_NEUTRAL,
- FILTER_RESULT_PASS,
- FILTER_RESULT_NOMATCH = FILTER_RESULT_BLOCK,
- FILTER_RESULT_MATCH = FILTER_RESULT_PASS,
-} FILTER_RESULT;
-
-//Forward declare
-class J2534Connection;
-
-/* Represents a J2534 Message Filter created by PassThruStartMsgFilter.
-
-J2534 uses filters to sort out messages in a simple and sane way. Except for
-flow control filters. J2534 v04.04 uses filters to manage 'conversations' in
-protocols that support flow control like ISO15765. The whole solution is a
-hack, and J2534 v05.00 greatly simplifies this concept. But we are using
-v04.04 so, here we are.
-*/
-class J2534MessageFilter {
-public:
- J2534MessageFilter(
- J2534Connection *const conn,
- unsigned int filtertype,
- PASSTHRU_MSG *pMaskMsg,
- PASSTHRU_MSG *pPatternMsg,
- PASSTHRU_MSG *pFlowControlMsg
- );
-
- bool J2534MessageFilter::operator ==(const J2534MessageFilter &b) const;
-
- FILTER_RESULT check(const J2534Frame& msg);
- std::string get_flowctrl();
-
- unsigned long flags;
- J2534Connection *const conn;
-private:
- unsigned int filtertype;
- std::string maskMsg;
- std::string patternMsg;
- std::string flowCtrlMsg;
-};
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534_v0404.h b/panda/drivers/windows/pandaJ2534DLL/J2534_v0404.h
deleted file mode 100644
index 7cccf6b42..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/J2534_v0404.h
+++ /dev/null
@@ -1,428 +0,0 @@
-//
-// Copyright (c) 2015-2016 DashLogic, Inc.
-// All Rights Reserved.
-//
-// http://www.dashlogic.com
-// sales@dashlogic.com
-//
-// Redistribution and use in source and binary forms, with or without
-// modification, including use for commercial purposes, are permitted
-// provided that the following conditions are met:
-//
-// 1. Redistributions of source code must retain the above copyright
-// notice, this list of conditions and the following disclaimer.
-//
-// 2. Redistributions in binary form must reproduce the above copyright
-// notice, this list of conditions and the following disclaimer in
-// the documentation and/or other materials provided with the
-// distribution.
-//
-// 3. Neither the name of the copyright holder nor the names of its
-// contributors may be used to endorse or promote products derived
-// from this software without specific prior written permission.
-//
-// 4. Redistributions of any form whatsoever must retain the following
-// acknowledgment: 'This product includes software developed by
-// "DashLogic, Inc." (http://www.dashlogic.com/).'
-//
-// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
-// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
-// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
-// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
-// HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
-// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
-// TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
-// PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
-// LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
-// NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-// SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-//
-
-
-//
-// Formatting:
-// Indents: Use tabs only (1 tab per indent)
-// Tab Size: 4 spaces
-//
-// File Revision:
-// $Rev: 5216 $
-// $Date: 2016-03-15 09:32:34 -0600 (Tue, 15 Mar 2016) $
-//
-
-#pragma once
-
-#ifdef PANDAJ2534DLL_EXPORTS
-#define PANDAJ2534DLL_API extern "C" __declspec(dllexport)
-#else
-#define PANDAJ2534DLL_API
-//__declspec(dllimport)
-#endif
-
-//
-// Platform-specific Defines:
-//
-// PTAPI: Define this yourself if you want a specific calling
-// convention or other modifiers on the Pass-Thru API
-// functions. Typically, on Windows, PTAPI will be defined
-// as WINAPI, which enables the __stdcall convention.
-//
-#define PTAPI __stdcall //WINAPI
-
-//
-// J2534-1 v04.04 ProtocolID Values
-//
-#define J1850VPW 0x01
-#define J1850PWM 0x02
-#define ISO9141 0x03
-#define ISO14230 0x04
-#define CAN 0x05
-#define ISO15765 0x06
-#define SCI_A_ENGINE 0x07
-#define SCI_A_TRANS 0x08
-#define SCI_B_ENGINE 0x09
-#define SCI_B_TRANS 0x0A
-
-
-//
-// J2534-2 ProtocolID Values
-//
-#define J1850VPW_PS 0x00008000
-#define J1850PWM_PS 0x00008001
-#define ISO9141_PS 0x00008002
-#define ISO14230_PS 0x00008003
-#define CAN_PS 0x00008004
-#define ISO15765_PS 0x00008005
-#define J2610_PS 0x00008006
-#define SW_ISO15765_PS 0x00008007
-#define SW_CAN_PS 0x00008008
-#define GM_UART_PS 0x00008009
-#define CAN_CH1 0x00009000
-#define CAN_CH2 (CAN_CH1 + 1)
-#define CAN_CH128 (CAN_CH1 + 127)
-#define J1850VPW_CH1 0x00009080
-#define J1850VPW_CH2 (J1850VPW_CH1 + 1)
-#define J1850VPW_CH128 (J1850VPW_CH1 + 127)
-#define J1850PWM_CH1 0x00009160
-#define J1850PWM_CH2 (J1850PWM_CH1 + 1)
-#define J1850PWM_CH128 (J1850PWM_CH1 + 127)
-#define ISO9141_CH1 0x00009240
-#define ISO9141_CH2 (ISO9141_CH1 + 1)
-#define ISO9141_CH128 (ISO9141_CH1 + 127)
-#define ISO14230_CH1 0x00009320
-#define ISO14230_CH2 (ISO14230_CH1 + 1)
-#define ISO14230_CH128 (ISO14230_CH1 + 127)
-#define ISO15765_CH1 0x00009400
-#define ISO15765_CH2 (ISO15765_CH1 + 1)
-#define ISO15765_CH128 (ISO15765_CH1 + 127)
-#define SW_CAN_CAN_CH1 0x00009480
-#define SW_CAN_CAN_CH2 (SW_CAN_CAN_CH1 + 1)
-#define SW_CAN_CAN_CH128 (SW_CAN_CAN_CH1 + 127)
-#define SW_CAN_ISO15765_CH1 0x00009560
-#define SW_CAN_ISO15765_CH2 (SW_CAN_ISO15765_CH1 + 1)
-#define SW_CAN_ISO15765_CH128 (SW_CAN_ISO15765_CH1 + 127)
-#define J2610_CH1 0x00009640
-#define J2610_CH2 (J2610_CH1 + 1)
-#define J2610_CH128 (J2610_CH1 + 127)
-#define ANALOG_IN_CH1 0x0000C000
-#define ANALOG_IN_CH2 0x0000C001
-#define ANALOG_IN_CH32 0x0000C01F
-
-
-//
-// J2534-1 v04.04 Error Values
-//
-#define STATUS_NOERROR 0x00 // Function call successful.
-#define ERR_NOT_SUPPORTED 0x01 // Device cannot support requested functionality mandated in J2534. Device is not fully SAE J2534 compliant.
-#define ERR_INVALID_CHANNEL_ID 0x02 // Invalid ChannelID value.
-#define ERR_INVALID_PROTOCOL_ID 0x03 // Invalid or unsupported ProtocolID, or there is a resource conflict (i.e. trying to connect to multiple mutually exclusive protocols such as J1850PWM and J1850VPW, or CAN and SCI, etc.).
-#define ERR_NULL_PARAMETER 0x04 // NULL pointer supplied where a valid pointer is required.
-#define ERR_INVALID_IOCTL_VALUE 0x05 // Invalid value for Ioctl parameter.
-#define ERR_INVALID_FLAGS 0x06 // Invalid flag values.
-#define ERR_FAILED 0x07 // Undefined error, use PassThruGetLastError() for text description.
-#define ERR_DEVICE_NOT_CONNECTED 0x08 // Unable to communicate with device.
-#define ERR_TIMEOUT 0x09 // Read or write timeout:
- // PassThruReadMsgs() - No message available to read or could not read the specified number of messages. The actual number of messages read is placed in .
- // PassThruWriteMsgs() - Device could not write the specified number of messages. The actual number of messages sent on the vehicle network is placed in .
-#define ERR_INVALID_MSG 0x0A // Invalid message structure pointed to by pMsg.
-#define ERR_INVALID_TIME_INTERVAL 0x0B // Invalid TimeInterval value.
-#define ERR_EXCEEDED_LIMIT 0x0C // Exceeded maximum number of message IDs or allocated space.
-#define ERR_INVALID_MSG_ID 0x0D // Invalid MsgID value.
-#define ERR_DEVICE_IN_USE 0x0E // Device is currently open.
-#define ERR_INVALID_IOCTL_ID 0x0F // Invalid IoctlID value.
-#define ERR_BUFFER_EMPTY 0x10 // Protocol message buffer empty, no messages available to read.
-#define ERR_BUFFER_FULL 0x11 // Protocol message buffer full. All the messages specified may not have been transmitted.
-#define ERR_BUFFER_OVERFLOW 0x12 // Indicates a buffer overflow occurred and messages were lost.
-#define ERR_PIN_INVALID 0x13 // Invalid pin number, pin number already in use, or voltage already applied to a different pin.
-#define ERR_CHANNEL_IN_USE 0x14 // Channel number is currently connected.
-#define ERR_MSG_PROTOCOL_ID 0x15 // Protocol type in the message does not match the protocol associated with the Channel ID
-#define ERR_INVALID_FILTER_ID 0x16 // Invalid Filter ID value.
-#define ERR_NO_FLOW_CONTROL 0x17 // No flow control filter set or matched (for ProtocolID ISO15765 only).
-#define ERR_NOT_UNIQUE 0x18 // A CAN ID in pPatternMsg or pFlowControlMsg matches either ID in an existing FLOW_CONTROL_FILTER
-#define ERR_INVALID_BAUDRATE 0x19 // The desired baud rate cannot be achieved within the tolerance specified in SAE J2534-1 Section 6.5
-#define ERR_INVALID_DEVICE_ID 0x1A // Device ID invalid.
-
-
-//
-// J2534-1 v04.04 Connect Flags
-//
-#define CAN_29BIT_ID 0x0100
-#define ISO9141_NO_CHECKSUM 0x0200
-#define CAN_ID_BOTH 0x0800
-#define ISO9141_K_LINE_ONLY 0x1000
-
-
-//
-// J2534-1 v04.04 Filter Type Values
-//
-#define PASS_FILTER 0x00000001
-#define BLOCK_FILTER 0x00000002
-#define FLOW_CONTROL_FILTER 0x00000003
-
-
-//
-// J2534-1 v04.04 Programming Voltage Pin Numbers
-//
-#define AUXILIARY_OUTPUT_PIN 0
-#define SAE_J1962_CONNECTOR_PIN_6 6
-#define SAE_J1962_CONNECTOR_PIN_9 9
-#define SAE_J1962_CONNECTOR_PIN_11 11
-#define SAE_J1962_CONNECTOR_PIN_12 12
-#define SAE_J1962_CONNECTOR_PIN_13 13
-#define SAE_J1962_CONNECTOR_PIN_14 14
-#define SAE_J1962_CONNECTOR_PIN_15 15 // Short to ground only
-
-
-//
-// J2534-1 v04.04 Programming Voltage Values
-//
-#define SHORT_TO_GROUND 0xFFFFFFFE
-#define VOLTAGE_OFF 0xFFFFFFFF
-
-
-//
-// J2534-1 v04.04 API Version Values
-//
-#define J2534_APIVER_FEBRUARY_2002 "02.02"
-#define J2534_APIVER_NOVEMBER_2004 "04.04"
-
-
-//
-// J2534-1 v04.04 IOCTL ID Values
-//
-#define GET_CONFIG 0x01 // pInput = SCONFIG_LIST, pOutput = NULL
-#define SET_CONFIG 0x02 // pInput = SCONFIG_LIST, pOutput = NULL
-#define READ_VBATT 0x03 // pInput = NULL, pOutput = unsigned long
-#define FIVE_BAUD_INIT 0x04 // pInput = SBYTE_ARRAY, pOutput = SBYTE_ARRAY
-#define FAST_INIT 0x05 // pInput = PASSTHRU_MSG, pOutput = PASSTHRU_MSG
-#define CLEAR_TX_BUFFER 0x07 // pInput = NULL, pOutput = NULL
-#define CLEAR_RX_BUFFER 0x08 // pInput = NULL, pOutput = NULL
-#define CLEAR_PERIODIC_MSGS 0x09 // pInput = NULL, pOutput = NULL
-#define CLEAR_MSG_FILTERS 0x0A // pInput = NULL, pOutput = NULL
-#define CLEAR_FUNCT_MSG_LOOKUP_TABLE 0x0B // pInput = NULL, pOutput = NULL
-#define ADD_TO_FUNCT_MSG_LOOKUP_TABLE 0x0C // pInput = SBYTE_ARRAY, pOutput = NULL
-#define DELETE_FROM_FUNCT_MSG_LOOKUP_TABLE 0x0D // pInput = SBYTE_ARRAY, pOutput = NULL
-#define READ_PROG_VOLTAGE 0x0E // pInput = NULL, pOutput = unsigned long
-
-
-//
-// J2534-2 IOCTL ID Values
-//
-#define SW_CAN_HS 0x00008000 // pInput = NULL, pOutput = NULL
-#define SW_CAN_NS 0x00008001 // pInput = NULL, pOutput = NULL
-#define SET_POLL_RESPONSE 0x00008002 // pInput = SBYTE_ARRAY, pOutput = NULL
-#define BECOME_MASTER 0x00008003 // pInput = unsigned char, pOutput = NULL
-
-
-//
-// J2534-1 v04.04 Configuration Parameter Values
-// Default value is enclosed in square brackets "[" and "]"
-//
-#define DATA_RATE 0x01 // 5-500000
-#define LOOPBACK 0x03 // 0 (OFF), 1 (ON) [0]
-#define NODE_ADDRESS 0x04 // J1850PWM: 0x00-0xFF
-#define NETWORK_LINE 0x05 // J1850PWM: 0 (BUS_NORMAL), 1 (BUS_PLUS), 2 (BUS_MINUS) [0]
-#define P1_MIN 0x06 // ISO9141 or ISO14230: Not used by interface
-#define P1_MAX 0x07 // ISO9141 or ISO14230: 0x1-0xFFFF (.5 ms per bit) [40 (20ms)]
-#define P2_MIN 0x08 // ISO9141 or ISO14230: Not used by interface
-#define P2_MAX 0x09 // ISO9141 or ISO14230: Not used by interface
-#define P3_MIN 0x0A // ISO9141 or ISO14230: 0x0-0xFFFF (.5 ms per bit) [110 (55ms)]
-#define P3_MAX 0x0B // ISO9141 or ISO14230: Not used by interface
-#define P4_MIN 0x0C // ISO9141 or ISO14230: 0x0-0xFFFF (.5 ms per bit) [10 (5ms)]
-#define P4_MAX 0x0D // ISO9141 or ISO14230: Not used by interface
-#define W0 0x19 // ISO9141: 0x0-0xFFFF (1 ms per bit) [300]
-#define W1 0x0E // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [300]
-#define W2 0x0F // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [20]
-#define W3 0x10 // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [20]
-#define W4 0x11 // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [50]
-#define W5 0x12 // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [300]
-#define TIDLE 0x13 // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [300]
-#define TINIL 0x14 // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [25]
-#define TWUP 0x15 // ISO9141 or ISO14230: 0x0-0xFFFF (1 ms per bit) [50]
-#define PARITY 0x16 // ISO9141 or ISO14230: 0 (NO_PARITY), 1 (ODD_PARITY), 2 (EVEN_PARITY) [0]
-#define BIT_SAMPLE_POINT 0x17 // CAN: 0-100 (1% per bit) [80]
-#define SYNC_JUMP_WIDTH 0x18 // CAN: 0-100 (1% per bit) [15]
-#define T1_MAX 0x1A // SCI: 0x0-0xFFFF (1 ms per bit) [20]
-#define T2_MAX 0x1B // SCI: 0x0-0xFFFF (1 ms per bit) [100]
-#define T3_MAX 0x24 // SCI: 0x0-0xFFFF (1 ms per bit) [50]
-#define T4_MAX 0x1C // SCI: 0x0-0xFFFF (1 ms per bit) [20]
-#define T5_MAX 0x1D // SCI: 0x0-0xFFFF (1 ms per bit) [100]
-#define ISO15765_BS 0x1E // ISO15765: 0x0-0xFF [0]
-#define ISO15765_STMIN 0x1F // ISO15765: 0x0-0xFF [0]
-#define ISO15765_BS_TX 0x22 // ISO15765: 0x0-0xFF,0xFFFF [0xFFFF]
-#define ISO15765_STMIN_TX 0x23 // ISO15765: 0x0-0xFF,0xFFFF [0xFFFF]
-#define DATA_BITS 0x20 // ISO9141 or ISO14230: 0 (8 data bits), 1 (7 data bits) [0]
-#define FIVE_BAUD_MOD 0x21 // ISO9141 or ISO14230: 0 (ISO 9141-2/14230-4), 1 (Inv KB2), 2 (Inv Addr), 3 (ISO 9141) [0]
-#define ISO15765_WFT_MAX 0x25 // ISO15765: 0x0-0xFF [0]
-
-
-//
-// J2534-2 Configuration Parameter Values
-// Default value is enclosed in square brackets "[" and "]"
-//
-#define CAN_MIXED_FORMAT 0x00008000 // See #defines below. [0]
-#define J1962_PINS 0x00008001 // 0xPPSS PP: 0x00-0x10 SS: 0x00-0x10 PP!=SS, except 0x0000. Exclude pins 4, 5, and 16. [0]
-#define SW_CAN_HS_DATA_RATE 0x00008010 // SWCAN: 5-500000 [83333]
-#define SW_CAN_SPEEDCHANGE_ENABLE 0x00008011 // SWCAN: 0 (DISABLE_SPDCHANGE), 1 (ENABLE_SPDCHANGE) [0]
-#define SW_CAN_RES_SWITCH 0x00008012 // SWCAN: 0 (DISCONNECT_RESISTOR), 1 (CONNECT_RESISTOR), 2 (AUTO_ RESISTOR) [0]
-#define ACTIVE_CHANNELS 0x00008020 // ANALOG: 0-0xFFFFFFFF
-#define SAMPLE_RATE 0x00008021 // ANALOG: 0-0xFFFFFFFF [0] (high bit changes meaning from samples/sec to seconds/sample)
-#define SAMPLES_PER_READING 0x00008022 // ANALOG: 1-0xFFFFFFFF [1]
-#define READINGS_PER_MSG 0x00008023 // ANALOG: 1-0x00000408 (1 - 1032) [1]
-#define AVERAGING_METHOD 0x00008024 // ANALOG: 0-0xFFFFFFFF [0]
-#define SAMPLE_RESOLUTION 0x00008025 // ANALOG READ-ONLY: 0x1-0x20 (1 - 32)
-#define INPUT_RANGE_LOW 0x00008026 // ANALOG READ-ONLY: 0x80000000-0x7FFFFFFF (-2147483648-2147483647)
-#define INPUT_RANGE_HIGH 0x00008027 // ANALOG READ-ONLY: 0x80000000-0x7FFFFFFF (-2147483648-2147483647)
-
-
-//
-// J2534-2 Mixed-Mode/Format CAN Definitions
-//
-#define CAN_MIXED_FORMAT_OFF 0 // Messages will be treated as ISO 15765 ONLY.
-#define CAN_MIXED_FORMAT_ON 1 // Messages will be treated as either ISO 15765 or an unformatted CAN frame.
-#define CAN_MIXED_FORMAT_ALL_FRAMES 2 // Messages will be treated as ISO 15765, an unformatted CAN frame, or both.
-
-
-//
-// J2534-2 Analog Channel Averaging Method Definitions
-//
-#define SIMPLE_AVERAGE 0x00000000 // Simple arithmetic mean
-#define MAX_LIMIT_AVERAGE 0x00000001 // Choose the biggest value
-#define MIN_LIMIT_AVERAGE 0x00000002 // Choose the lowest value
-#define MEDIAN_AVERAGE 0x00000003 // Choose arithmetic median
-
-
-//
-// J2534-1 v04.04 RxStatus Definitions
-//
-#define TX_MSG_TYPE 0x0001
-#define START_OF_MESSAGE 0x0002
-#define RX_BREAK 0x0004
-#define TX_INDICATION 0x0008
-#define ISO15765_PADDING_ERROR 0x0010
-#define ISO15765_ADDR_TYPE 0x0080
-//#define CAN_29BIT_ID 0x0100 // Defined above
-
-
-//
-// J2534-2 RxStatus Definitions
-//
-#define SW_CAN_HV_RX 0x00010000 // SWCAN Channels Only
-#define SW_CAN_HS_RX 0x00020000 // SWCAN Channels Only
-#define SW_CAN_NS_RX 0x00040000 // SWCAN Channels Only
-#define OVERFLOW_ 0x00010000 // Analog Input Channels Only
-
-
-//
-// J2534-1 v04.04 TxFlags Definitions
-//
-#define ISO15765_FRAME_PAD 0x0040
-//#define ISO15765_ADDR_TYPE 0x0080 // Defined above
-//#define CAN_29BIT_ID 0x0100 // Defined above
-#define WAIT_P3_MIN_ONLY 0x0200
-#define SCI_MODE 0x400000
-#define SCI_TX_VOLTAGE 0x800000
-
-
-//
-// J2534-2 TxFlags Definitions
-//
-#define SW_CAN_HV_TX 0x00000400
-
-
-//
-// J2534-1 v04.04 Structure Definitions
-//
-typedef struct
-{
- unsigned long Parameter; // Name of parameter
- unsigned long Value; // Value of the parameter
-} SCONFIG;
-
-
-typedef struct
-{
- unsigned long NumOfParams; // Number of SCONFIG elements
- SCONFIG* ConfigPtr; // Array of SCONFIG
-} SCONFIG_LIST;
-
-
-typedef struct
-{
- unsigned long NumOfBytes; // Number of bytes in the array
- unsigned char* BytePtr; // Array of bytes
-} SBYTE_ARRAY;
-
-
-typedef struct
-{
- unsigned long ProtocolID;
- unsigned long RxStatus;
- unsigned long TxFlags;
- unsigned long Timestamp;
- unsigned long DataSize;
- unsigned long ExtraDataIndex;
- unsigned char Data[4128];
-} PASSTHRU_MSG;
-
-//
-// J2534-1 v04.04 Function Prototypes
-//
-PANDAJ2534DLL_API long PTAPI PassThruOpen(void *pName, unsigned long *pDeviceID);
-PANDAJ2534DLL_API long PTAPI PassThruClose(unsigned long DeviceID);
-PANDAJ2534DLL_API long PTAPI PassThruConnect(unsigned long DeviceID, unsigned long ProtocolID, unsigned long Flags, unsigned long BaudRate, unsigned long *pChannelID);
-PANDAJ2534DLL_API long PTAPI PassThruDisconnect(unsigned long ChannelID);
-PANDAJ2534DLL_API long PTAPI PassThruReadMsgs(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout);
-PANDAJ2534DLL_API long PTAPI PassThruWriteMsgs(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout);
-PANDAJ2534DLL_API long PTAPI PassThruStartPeriodicMsg(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pMsgID, unsigned long TimeInterval);
-PANDAJ2534DLL_API long PTAPI PassThruStopPeriodicMsg(unsigned long ChannelID, unsigned long MsgID);
-PANDAJ2534DLL_API long PTAPI PassThruStartMsgFilter(unsigned long ChannelID, unsigned long FilterType, PASSTHRU_MSG *pMaskMsg, PASSTHRU_MSG *pPatternMsg, PASSTHRU_MSG *pFlowControlMsg, unsigned long *pFilterID);
-PANDAJ2534DLL_API long PTAPI PassThruStopMsgFilter(unsigned long ChannelID, unsigned long FilterID);
-PANDAJ2534DLL_API long PTAPI PassThruSetProgrammingVoltage(unsigned long DeviceID, unsigned long PinNumber, unsigned long Voltage);
-PANDAJ2534DLL_API long PTAPI PassThruReadVersion(unsigned long DeviceID, char *pFirmwareVersion, char *pDllVersion, char *pApiVersion);
-PANDAJ2534DLL_API long PTAPI PassThruGetLastError(char *pErrorDescription);
-PANDAJ2534DLL_API long PTAPI PassThruIoctl(unsigned long ChannelID, unsigned long IoctlID, void *pInput, void *pOutput);
-
-
-//
-// J2534-1 v04.04 Function Typedefs
-// These function typedefs allow simpler use of the J2534 API by
-// allowing you to do things like this:
-// PTCONNECT pPassThruConnectFunc = GetProcAddress(hModule, "PassThruConnect");
-// if (pPassThruConnectFunc == NULL)
-// return FALSE;
-// pPassThruConnectFunc(DeviceID, CAN, CAN_29BIT_ID, 500000, &ChannelID);
-//
-typedef long (PTAPI *PTOPEN)(void *pName, unsigned long *pDeviceID);
-typedef long (PTAPI *PTCLOSE)(unsigned long DeviceID);
-typedef long (PTAPI *PTCONNECT)(unsigned long DeviceID, unsigned long ProtocolID, unsigned long Flags, unsigned long BaudRate, unsigned long *pChannelID);
-typedef long (PTAPI *PTDISCONNECT)(unsigned long ChannelID);
-typedef long (PTAPI *PTREADMSGS)(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout);
-typedef long (PTAPI *PTWRITEMSGS)(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pNumMsgs, unsigned long Timeout);
-typedef long (PTAPI *PTSTARTPERIODICMSG)(unsigned long ChannelID, PASSTHRU_MSG *pMsg, unsigned long *pMsgID, unsigned long TimeInterval);
-typedef long (PTAPI *PTSTOPPERIODICMSG)(unsigned long ChannelID, unsigned long MsgID);
-typedef long (PTAPI *PTSTARTMSGFILTER)(unsigned long ChannelID, unsigned long FilterType, PASSTHRU_MSG *pMaskMsg, PASSTHRU_MSG *pPatternMsg, PASSTHRU_MSG *pFlowControlMsg, unsigned long *pFilterID);
-typedef long (PTAPI *PTSTOPMSGFILTER)(unsigned long ChannelID, unsigned long FilterID);
-typedef long (PTAPI *PTSETPROGRAMMINGVOLTAGE)(unsigned long DeviceID, unsigned long PinNumber, unsigned long Voltage);
-typedef long (PTAPI *PTREADVERSION)(unsigned long DeviceID, char *pFirmwareVersion, char *pDllVersion, char *pApiVersion);
-typedef long (PTAPI *PTGETLASTERROR)(char *pErrorDescription);
-typedef long (PTAPI *PTIOCTL)(unsigned long ChannelID, unsigned long IoctlID, void *pInput, void *pOutput);
diff --git a/panda/drivers/windows/pandaJ2534DLL/J2534register_x64.reg b/panda/drivers/windows/pandaJ2534DLL/J2534register_x64.reg
deleted file mode 100644
index 120ab391c..000000000
Binary files a/panda/drivers/windows/pandaJ2534DLL/J2534register_x64.reg and /dev/null differ
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessagePeriodic.cpp b/panda/drivers/windows/pandaJ2534DLL/MessagePeriodic.cpp
deleted file mode 100644
index 0c3416e0d..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessagePeriodic.cpp
+++ /dev/null
@@ -1,30 +0,0 @@
-#include "stdafx.h"
-#include "MessagePeriodic.h"
-#include "J2534Connection.h"
-
-MessagePeriodic::MessagePeriodic(
- std::chrono::microseconds delay,
- std::shared_ptr msg
-) : Action(msg->connection, delay), msg(msg), runyet(FALSE), active(TRUE) { };
-
-void MessagePeriodic::execute() {
- if (!this->active) return;
- if (this->runyet) {
- if (msg->isFinished()) {
- msg->reset();
- msg->execute();
- }
- } else {
- this->runyet = TRUE;
- msg->execute();
- }
-
- if (auto conn_sp = this->connection.lock()) {
- if (auto panda_dev_sp = conn_sp->getPandaDev()) {
- //Scheduling must be relative to now incase there was a long stall that
- //would case it to be super far behind and try to catch up forever.
- this->scheduleImmediateDelay();
- panda_dev_sp->insertActionIntoTaskList(shared_from_this());
- }
- }
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessagePeriodic.h b/panda/drivers/windows/pandaJ2534DLL/MessagePeriodic.h
deleted file mode 100644
index 40132565c..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessagePeriodic.h
+++ /dev/null
@@ -1,33 +0,0 @@
-#pragma once
-#include "Action.h"
-#include "MessageTx.h"
-
-class J2534Connection;
-
-/* A message that is resent on a given period. Created with calls to PassThruStartPeriodicMessage.
-
-Instead of making each J2534 protocol implementation have to implement periodic message
-functionality, this class takes a message to be sent, and passes along the execute call
-to the message, then reschedules itself.
-*/
-class MessagePeriodic : public Action, public std::enable_shared_from_this
-{
-public:
- MessagePeriodic(
- std::chrono::microseconds delay,
- std::shared_ptr msg
- );
-
- virtual void execute();
-
- void cancel() {
- this->active = FALSE;
- }
-
-protected:
- std::shared_ptr msg;
-
-private:
- BOOL runyet;
- BOOL active;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageRx.h b/panda/drivers/windows/pandaJ2534DLL/MessageRx.h
deleted file mode 100644
index e22278d4d..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageRx.h
+++ /dev/null
@@ -1,61 +0,0 @@
-#pragma once
-
-class MessageRx
-{
-public:
- MessageRx(
- unsigned long size,
- std::string piece,
- unsigned long rxFlags,
- std::shared_ptr filter
- ) : expected_size(size & 0xFFF), flags(rxFlags) {
- msg.reserve(expected_size);
- msg = piece;
- next_part = 1;
- };
-
- bool rx_add_frame(uint8_t pci_byte, unsigned int max_packet_size, const std::string piece) {
- if ((pci_byte & 0x0F) != this->next_part) {
- //TODO: Maybe this should instantly fail the transaction.
- return TRUE;
- }
-
- this->next_part = (this->next_part + 1) % 0x10;
- unsigned int payload_len = min(expected_size - msg.size(), max_packet_size);
- if (piece.size() < payload_len) {
- //A frame was received that could have held more data.
- //No examples of this protocol show that happening, so
- //it will be assumed that it is grounds to reset rx.
- return FALSE;
- }
- msg += piece.substr(0, payload_len);
-
- return TRUE;
- }
-
- unsigned int bytes_remaining() {
- return this->expected_size - this->msg.size();
- }
-
- bool is_ready() {
- return this->msg.size() == this->expected_size;
- }
-
- bool flush_result(std::string& final_msg) {
- if (this->msg.size() == this->expected_size) {
- final_msg = this->msg;
- return TRUE;
- }
- return FALSE;
- }
-
- uint8_t getNextConsecutiveFrameId() {
- return this->next_part++;
- }
-
- std::weak_ptr filter;
- unsigned long flags;
- unsigned long expected_size;
- std::string msg;
- unsigned char next_part;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTx.h b/panda/drivers/windows/pandaJ2534DLL/MessageTx.h
deleted file mode 100644
index 5315fa058..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTx.h
+++ /dev/null
@@ -1,25 +0,0 @@
-#pragma once
-#include "Action.h"
-#include "J2534Frame.h"
-
-class J2534Connection;
-
-class MessageTx : public Action, public std::enable_shared_from_this
-{
-public:
- MessageTx(
- std::weak_ptr connection_in,
- PASSTHRU_MSG& to_send
- ) : Action(connection_in), fullmsg(to_send) { };
-
- virtual BOOL checkTxReceipt(J2534Frame frame) = 0;
-
- virtual BOOL isFinished() = 0;
-
- virtual BOOL txReady() = 0;
-
- virtual void reset() = 0;
-
-protected:
- J2534Frame fullmsg;
-};
\ No newline at end of file
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTxTimeout.cpp b/panda/drivers/windows/pandaJ2534DLL/MessageTxTimeout.cpp
deleted file mode 100644
index 2e21ba3ce..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTxTimeout.cpp
+++ /dev/null
@@ -1,43 +0,0 @@
-#include "stdafx.h"
-#include "J2534Connection.h"
-#include "MessageTxTimeout.h"
-
-MessageTxTimeoutable::MessageTxTimeoutable(
- std::weak_ptr connection,
- PASSTHRU_MSG& to_send
-) : MessageTx(connection, to_send), recvCount(0) { };
-
-void MessageTxTimeoutable::scheduleTimeout(std::chrono::microseconds timeoutus) {
- if (auto conn_sp = this->connection.lock()) {
- if (auto panda_dev_sp = conn_sp->getPandaDev()) {
- auto timeoutobj = std::make_shared(std::static_pointer_cast(shared_from_this()), timeoutus);
- panda_dev_sp->scheduleAction(std::static_pointer_cast(timeoutobj), TRUE);
- }
- }
-}
-
-void MessageTxTimeoutable::scheduleTimeout(unsigned long timeoutus) {
- scheduleTimeout(std::chrono::microseconds(timeoutus));
-}
-
-
-
-MessageTxTimeout::MessageTxTimeout(
- std::shared_ptr msg,
- std::chrono::microseconds timeout
-) : Action(msg->connection), msg(msg), lastRecvCount(msg->getRecvCount()) {
- delay = timeout;
-};
-
-MessageTxTimeout::MessageTxTimeout(
- std::shared_ptr msg,
- unsigned long timeout
-) : MessageTxTimeout(msg, std::chrono::microseconds(timeout * 1000)) { };
-
-void MessageTxTimeout::execute() {
- if (auto msg_sp = this->msg.lock()) {
- if (msg_sp->getRecvCount() == this->lastRecvCount) {
- msg_sp->onTimeout();
- }
- }
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTxTimeout.h b/panda/drivers/windows/pandaJ2534DLL/MessageTxTimeout.h
deleted file mode 100644
index a9c878468..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTxTimeout.h
+++ /dev/null
@@ -1,52 +0,0 @@
-#pragma once
-#include "Action.h"
-#include "MessageTx.h"
-
-class MessageTxTimeout;
-
-/* A special type of MessageTx for multipart messages that supports being canceled with a timeout.*/
-class MessageTxTimeoutable : public MessageTx
-{
-public:
- MessageTxTimeoutable(
- std::weak_ptr connection,
- PASSTHRU_MSG& to_send
- );
-
- unsigned long getRecvCount() {
- return recvCount;
- }
-
- virtual void onTimeout() = 0;
-
-protected:
- unsigned long recvCount;
-
- void scheduleTimeout(std::chrono::microseconds timeoutus);
-
- void scheduleTimeout(unsigned long timeoutus);
-};
-
-
-/* An Action that cancels MessageTxTimeoutableif the Timeout Actoin executes
-before the MessageTxTimeoutableif renews its timeout.
-*/
-class MessageTxTimeout : public Action
-{
-public:
- MessageTxTimeout(
- std::shared_ptr msg,
- std::chrono::microseconds timeout
- );
-
- MessageTxTimeout(
- std::shared_ptr msg,
- unsigned long timeout
- );
-
- virtual void execute();
-
-private:
- std::weak_ptr msg;
- unsigned long lastRecvCount;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTx_CAN.cpp b/panda/drivers/windows/pandaJ2534DLL/MessageTx_CAN.cpp
deleted file mode 100644
index 8217ce539..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTx_CAN.cpp
+++ /dev/null
@@ -1,44 +0,0 @@
-#include "stdafx.h"
-#include "MessageTx_CAN.h"
-#include "J2534Connection_CAN.h"
-
-MessageTx_CAN::MessageTx_CAN(
- std::shared_ptr connection_in,
- PASSTHRU_MSG& to_send
-) : MessageTx(connection_in, to_send), sentyet(FALSE), txInFlight(FALSE) {};
-
-void MessageTx_CAN::execute() {
- uint32_t addr = ((uint8_t)fullmsg.Data[0]) << 24 | ((uint8_t)fullmsg.Data[1]) << 16 |
- ((uint8_t)fullmsg.Data[2]) << 8 | ((uint8_t)fullmsg.Data[3]);
-
- if (auto conn_sp = std::static_pointer_cast(this->connection.lock())) {
- if (auto panda_dev_sp = conn_sp->getPandaDev()) {
- auto payload = fullmsg.Data.substr(4);
- if (panda_dev_sp->panda->can_send(addr, check_bmask(this->fullmsg.TxFlags, CAN_29BIT_ID),
- (const uint8_t*)payload.c_str(), (uint8_t)payload.size(), panda::PANDA_CAN1) == FALSE) {
- return;
- }
- this->txInFlight = TRUE;
- this->sentyet = TRUE;
- panda_dev_sp->txMsgsAwaitingEcho.push(shared_from_this());
- }
- }
-}
-
-//Returns TRUE if receipt is consumed by the msg, FALSE otherwise.
-BOOL MessageTx_CAN::checkTxReceipt(J2534Frame frame) {
- if (txReady()) return FALSE;
- if (frame.Data == fullmsg.Data && ((this->fullmsg.TxFlags & CAN_29BIT_ID) == (frame.RxStatus & CAN_29BIT_ID))) {
- txInFlight = FALSE;
- if (auto conn_sp = std::static_pointer_cast(this->connection.lock()))
- if (conn_sp->loopback)
- conn_sp->addMsgToRxQueue(frame);
- return TRUE;
- }
- return FALSE;
-}
-
-void MessageTx_CAN::reset() {
- sentyet = FALSE;
- txInFlight = FALSE;
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTx_CAN.h b/panda/drivers/windows/pandaJ2534DLL/MessageTx_CAN.h
deleted file mode 100644
index afac75ef8..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTx_CAN.h
+++ /dev/null
@@ -1,33 +0,0 @@
-#pragma once
-#include
-#include "MessageTx.h"
-
-class J2534Connection;
-
-class MessageTx_CAN : public MessageTx
-{
-public:
- MessageTx_CAN(
- std::shared_ptr connection_in,
- PASSTHRU_MSG& to_send
- );
-
- virtual void execute();
-
- //Returns TRUE if receipt is consumed by the msg, FALSE otherwise.
- virtual BOOL checkTxReceipt(J2534Frame frame);
-
- virtual BOOL isFinished() {
- return !txInFlight && sentyet;
- };
-
- virtual BOOL txReady() {
- return !sentyet;
- };
-
- virtual void reset();
-
-private:
- BOOL sentyet;
- BOOL txInFlight;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTx_ISO15765.cpp b/panda/drivers/windows/pandaJ2534DLL/MessageTx_ISO15765.cpp
deleted file mode 100644
index 023088d3c..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTx_ISO15765.cpp
+++ /dev/null
@@ -1,180 +0,0 @@
-#include "stdafx.h"
-#include "MessageTx_ISO15765.h"
-#include "constants_ISO15765.h"
-
-//in microseconsa
-#define TIMEOUT_FC 250000 //Flow Control
-#define TIMEOUT_CF 250000 //Consecutive Frames
-
-MessageTx_ISO15765::MessageTx_ISO15765(
- std::shared_ptr connection_in,
- PASSTHRU_MSG& to_send,
- std::shared_ptr filter
-) : MessageTxTimeoutable(connection_in, to_send), filter(filter), frames_sent(0),
-consumed_count(0), txInFlight(FALSE), sendAll(FALSE), block_size(0), numWaitFrames(0), didtimeout(FALSE), issuspended(FALSE){
-
- CANid = ((uint8_t)fullmsg.Data[0]) << 24 | ((uint8_t)fullmsg.Data[1]) << 16 |
- ((uint8_t)fullmsg.Data[2]) << 8 | ((uint8_t)fullmsg.Data[3]);
-
- payload = fullmsg.Data.substr(addressLength());
-
- if (check_bmask(fullmsg.TxFlags, ISO15765_ADDR_TYPE))
- data_prefix = fullmsg.Data[4];
-
- if (payload.size() <= (7 - data_prefix.size())) {
- isMultipart = FALSE;
- auto framepayload = data_prefix + std::string(1, (char)payload.size()) + payload;
- if (check_bmask(this->fullmsg.TxFlags, ISO15765_FRAME_PAD))
- framepayload += std::string(8 - framepayload.size(), '\x00');
- framePayloads.push_back(framepayload);
- } else {
- isMultipart = TRUE;
- unsigned long first_payload_len = 6 - data_prefix.size(); // 5 or 6
- std::string framepayload = data_prefix +
- (char)(0x10 | ((payload.size() >> 8) & 0xF)) +
- (char)(payload.size() & 0xFF) +
- payload.substr(0, first_payload_len);
- framePayloads.push_back(framepayload);
-
- unsigned int pktnum = 1;
- uint8_t CFDatSize = 7 - data_prefix.size();
- while (TRUE) {
- framepayload = data_prefix + (char)(0x20 | (pktnum % 0x10)) +
- payload.substr(first_payload_len + (CFDatSize * (pktnum-1)), CFDatSize);
-
- if (check_bmask(this->fullmsg.TxFlags, ISO15765_FRAME_PAD))
- framepayload += std::string(8 - framepayload.size(), '\x00');
- framePayloads.push_back(framepayload);
- if (first_payload_len + (CFDatSize * pktnum) >= payload.size()) break;
- pktnum++;
- }
-
- }
-};
-
-unsigned int MessageTx_ISO15765::addressLength() {
- return check_bmask(fullmsg.TxFlags, ISO15765_ADDR_TYPE) ? 5 : 4;
-}
-
-void MessageTx_ISO15765::execute() {
- if (didtimeout || issuspended) return;
- if (this->frames_sent >= this->framePayloads.size()) return;
- if (block_size == 0 && !sendAll && this->frames_sent > 0) return;
- if (block_size > 0 && !sendAll) block_size--;
-
- if (auto conn_sp = this->connection.lock()) {
- if (auto panda_dev_sp = conn_sp->getPandaDev()) {
- auto& outFramePayload = this->framePayloads[this->frames_sent];
- if (panda_dev_sp->panda->can_send(this->CANid, check_bmask(this->fullmsg.TxFlags, CAN_29BIT_ID),
- (const uint8_t*)outFramePayload.c_str(), (uint8_t)outFramePayload.size(), panda::PANDA_CAN1) == FALSE) {
- return;
- }
-
- this->txInFlight = TRUE;
- this->frames_sent++;
- panda_dev_sp->txMsgsAwaitingEcho.push(shared_from_this());
- }
- }
-}
-
-//Returns TRUE if receipt is consumed by the msg, FALSE otherwise.
-BOOL MessageTx_ISO15765::checkTxReceipt(J2534Frame frame) {
- if (!txInFlight) return FALSE;
- if (frame.Data.size() >= addressLength() + 1 && (frame.Data[addressLength()] & 0xF0) == FRAME_FLOWCTRL) return FALSE;
-
- if (frame.Data == fullmsg.Data.substr(0, 4) + framePayloads[frames_sent - 1] &&
- ((this->fullmsg.TxFlags & CAN_29BIT_ID) == (frame.RxStatus & CAN_29BIT_ID))) { //Check receipt is expected
- txInFlight = FALSE; //Received the expected receipt. Allow another msg to be sent.
-
- if (this->recvCount == 0 && this->framePayloads.size() > 1)
- scheduleTimeout(TIMEOUT_FC);
-
- if (frames_sent == framePayloads.size()) { //Check message done
- if (auto conn_sp = std::static_pointer_cast(this->connection.lock())) {
- unsigned long flags = (filter == nullptr) ? fullmsg.TxFlags : this->filter->flags;
-
- J2534Frame outframe(ISO15765);
- outframe.Timestamp = frame.Timestamp;
- outframe.RxStatus = TX_MSG_TYPE | TX_INDICATION | (flags & (ISO15765_ADDR_TYPE | CAN_29BIT_ID));
- outframe.Data = frame.Data.substr(0, addressLength());
- conn_sp->addMsgToRxQueue(outframe);
-
- if (conn_sp->loopback) {
- J2534Frame outframe(ISO15765);
- outframe.Timestamp = frame.Timestamp;
- outframe.RxStatus = TX_MSG_TYPE | (flags & (ISO15765_ADDR_TYPE | CAN_29BIT_ID));
- outframe.Data = this->fullmsg.Data;
- conn_sp->addMsgToRxQueue(outframe);
- }
-
- } //TODO what if fails
- } else {
- //Restart timeout if we are waiting for a flow control frame.
- //FC frames are required when we are not sending all, the
- //current block_size batch has not been sent, a FC message has
- //already been received (differentiating from first frame), the
- //message is not finished, and there is more than one frame in
- //the message.
- if (block_size == 0 && recvCount != 0 && !sendAll && !this->isFinished() && this->framePayloads.size() > 1)
- scheduleTimeout(TIMEOUT_CF);
- }
- return TRUE;
- }
- return FALSE;
-}
-
-BOOL MessageTx_ISO15765::isFinished() {
- return this->frames_sent == this->framePayloads.size() && !txInFlight;
-}
-
-BOOL MessageTx_ISO15765::txReady() {
- return block_size > 0 || sendAll || this->frames_sent == 0;
-}
-
-void MessageTx_ISO15765::reset() {
- frames_sent = 0;
- consumed_count = 0;
- block_size = 0;
- txInFlight = FALSE;
- sendAll = FALSE;
- numWaitFrames = 0;
- didtimeout = FALSE;
-}
-
-void MessageTx_ISO15765::onTimeout() {
- didtimeout = TRUE;
- if (auto conn_sp = std::static_pointer_cast(this->connection.lock())) {
- if (auto panda_dev_sp = conn_sp->getPandaDev()) {
- panda_dev_sp->removeConnectionTopAction(conn_sp, shared_from_this());
- }
- }
-}
-
-void MessageTx_ISO15765::flowControlContinue(uint8_t block_size, std::chrono::microseconds separation_time) {
- this->issuspended = FALSE;
- this->block_size = block_size;
- this->delay = separation_time;
- this->sendAll = block_size == 0;
- this->recvCount++;
-}
-
-void MessageTx_ISO15765::flowControlWait(unsigned long N_WFTmax) {
- this->issuspended = TRUE;
- this->recvCount++;
- this->numWaitFrames++;
- this->sendAll = FALSE;
- this->block_size = block_size;
- this->delay = std::chrono::microseconds(0);
- //Docs are vague on if 0 means NO WAITS ALLOWED or NO LIMIT TO WAITS.
- //It is less likely to cause issue if NO LIMIT is assumed.
- if (N_WFTmax > 0 && this->numWaitFrames > N_WFTmax) {
- this->onTimeout(); //Trigger self destruction of message.
- } else {
- scheduleTimeout(TIMEOUT_FC);
- }
-}
-
-void MessageTx_ISO15765::flowControlAbort() {
- this->recvCount++; //Invalidate future timeout actions.
- this->onTimeout(); //Trigger self destruction of message.
-}
diff --git a/panda/drivers/windows/pandaJ2534DLL/MessageTx_ISO15765.h b/panda/drivers/windows/pandaJ2534DLL/MessageTx_ISO15765.h
deleted file mode 100644
index 0113edb8f..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/MessageTx_ISO15765.h
+++ /dev/null
@@ -1,54 +0,0 @@
-#pragma once
-#include "MessageTxTimeout.h"
-#include "J2534Connection_ISO15765.h"
-
-class J2534Connection_ISO15765;
-
-/**
-A specialized message type that can handle J2534 single and multi
-frame (with flow control) writes.
-*/
-class MessageTx_ISO15765 : public MessageTxTimeoutable
-{
-public:
- MessageTx_ISO15765(
- std::shared_ptr connection,
- PASSTHRU_MSG& to_send,
- std::shared_ptr filter
- );
-
- unsigned int addressLength();
-
- virtual void execute();
-
- virtual BOOL checkTxReceipt(J2534Frame frame);
-
- virtual BOOL isFinished();
-
- virtual BOOL txReady();
-
- virtual void reset();
-
- virtual void onTimeout();
-
- //Functions for ISO15765 flow control
-
- void MessageTx_ISO15765::flowControlContinue(uint8_t block_size, std::chrono::microseconds separation_time);
- void MessageTx_ISO15765::flowControlWait(unsigned long N_WFTmax);
- void MessageTx_ISO15765::flowControlAbort();
-
- std::shared_ptr filter;
- unsigned long frames_sent;
- unsigned long consumed_count;
- uint8_t block_size;
- unsigned long CANid;
- std::string data_prefix;
- std::string payload;
- BOOL isMultipart;
- std::vector framePayloads;
- BOOL txInFlight;
- BOOL sendAll;
- unsigned int numWaitFrames;
- BOOL didtimeout;
- BOOL issuspended;
-};
diff --git a/panda/drivers/windows/pandaJ2534DLL/PandaJ2534Device.cpp b/panda/drivers/windows/pandaJ2534DLL/PandaJ2534Device.cpp
deleted file mode 100644
index 1b961579e..000000000
--- a/panda/drivers/windows/pandaJ2534DLL/PandaJ2534Device.cpp
+++ /dev/null
@@ -1,238 +0,0 @@
-#include "stdafx.h"
-#include "PandaJ2534Device.h"
-#include "J2534Frame.h"
-
-PandaJ2534Device::PandaJ2534Device(std::unique_ptr new_panda) : txInProgress(FALSE) {
- this->panda = std::move(new_panda);
-
- this->panda->set_esp_power(FALSE);
- this->panda->set_safety_mode(panda::SAFETY_ALLOUTPUT);
- this->panda->set_can_loopback(FALSE);
- this->panda->set_alt_setting(0);
-
- this->thread_kill_event = CreateEvent(NULL, TRUE, FALSE, NULL);
-
- DWORD canListenThreadID;
- this->can_recv_handle = CreateThread(NULL, 0, _can_recv_threadBootstrap, (LPVOID)this, 0, &canListenThreadID);
-
- DWORD canProcessThreadID;
- this->can_process_handle = CreateThread(NULL, 0, _can_process_threadBootstrap, (LPVOID)this, 0, &canProcessThreadID);
-
- DWORD flowControlSendThreadID;
- this->flow_control_wakeup_event = CreateEvent(NULL, TRUE, FALSE, NULL);
- this->flow_control_thread_handle = CreateThread(NULL, 0, _msg_tx_threadBootstrap, (LPVOID)this, 0, &flowControlSendThreadID);
-};
-
-PandaJ2534Device::~PandaJ2534Device() {
- SetEvent(this->thread_kill_event);
- DWORD res = WaitForSingleObject(this->can_recv_handle, INFINITE);
- CloseHandle(this->can_recv_handle);
-
- res = WaitForSingleObject(this->can_process_handle, INFINITE);
- CloseHandle(this->can_process_handle);
-
- res = WaitForSingleObject(this->flow_control_thread_handle, INFINITE);
- CloseHandle(this->flow_control_thread_handle);
-
- CloseHandle(this->flow_control_wakeup_event);
- CloseHandle(this->thread_kill_event);
-}
-
-std::shared_ptr PandaJ2534Device::openByName(std::string sn) {
- auto p = panda::Panda::openPanda("");
- if (p == nullptr)
- return nullptr;
- return std::unique_ptr(new PandaJ2534Device(std::move(p)));
-}
-
-DWORD PandaJ2534Device::closeChannel(unsigned long ChannelID) {
- if (this->connections.size() <= ChannelID) return ERR_INVALID_CHANNEL_ID;
- if (this->connections[ChannelID] == nullptr) return ERR_INVALID_CHANNEL_ID;
- this->connections[ChannelID] = nullptr;
- return STATUS_NOERROR;
-}
-
-DWORD PandaJ2534Device::addChannel(std::shared_ptr& conn, unsigned long* channel_id) {
- int channel_index = -1;
- for (unsigned int i = 0; i < this->connections.size(); i++)
- if (this->connections[i] == nullptr) {
- channel_index = i;
- break;
- }
-
- if (channel_index == -1) {
- if (this->connections.size() == 0xFFFF) //channelid max 16 bits
- return ERR_FAILED; //Too many channels
- this->connections.push_back(nullptr);
- channel_index = this->connections.size() - 1;
- }
-
- this->connections[channel_index] = conn;
-
- *channel_id = channel_index;
- return STATUS_NOERROR;
-}
-
-DWORD PandaJ2534Device::can_recv_thread() {
- this->panda->can_clear(panda::PANDA_CAN_RX);
- this->panda->can_rx_q_push(this->thread_kill_event);
-
- return 0;
-}
-
-DWORD PandaJ2534Device::can_process_thread() {
- panda::PANDA_CAN_MSG msg_recv[CAN_RX_MSG_LEN];
-
- while (true) {
- if (!WaitForSingleObject(this->thread_kill_event, 0)) {
- break;
- }
-
- int count = 0;
- this->panda->can_rx_q_pop(msg_recv, count);
- if (count == 0) {
- continue;
- }
-
- for (int i = 0; i < count; i++) {
- auto msg_in = msg_recv[i];
- J2534Frame msg_out(msg_in);
-
- if (msg_in.is_receipt) {
- synchronized(task_queue_mutex) {
- if (txMsgsAwaitingEcho.size() > 0) {
- auto msgtx = txMsgsAwaitingEcho.front();
- if (auto conn = msgtx->connection.lock()) {
- if (conn->isProtoCan() && conn->getPort() == msg_in.bus) {
- if (msgtx->checkTxReceipt(msg_out)) {
- //Things to check:
- // Frame not for this msg: Drop frame and alert. Error?
- // Frame is for this msg, more tx frames required after a FC frame: Wait for FC frame to come and trigger next tx.
- // Frame is for this msg, more tx frames required: Schedule next tx frame.
- // Frame is for this msg, and is the final frame of the msg: Let conn process full msg, If another msg from this conn is available, register it.
- txMsgsAwaitingEcho.pop(); //Remove the TX object and schedule record.
-
- if (msgtx->isFinished()) {
- this->removeConnectionTopAction(conn, msgtx);
- } else {
- if (msgtx->txReady()) { //Not finished, ready to send next frame.
- msgtx->schedule(msg_in.recv_time_point, TRUE);
- this->insertActionIntoTaskList(msgtx);
- } else {
- //Not finished, but next frame not ready (maybe waiting for flow control).
- //Do not schedule more messages from this connection.
- //this->ConnTxSet.erase(conn);
- //Removing this means new messages queued can kickstart the queue and overstep the current message.
- }
- }
- }
- }
- } else {
- //Connection has died. Clear out the tx entry from device records.
- txMsgsAwaitingEcho.pop();
- this->ConnTxSet.erase(conn); //connection is already dead, no need to schedule future tx msgs.
- }
- }
- }
- } else {
- for (auto& conn : this->connections)
- if (conn != nullptr && conn->isProtoCan() && conn->getPort() == msg_in.bus)
- conn->processMessage(msg_out);
- }
- }
- }
-
- return 0;
-}
-
-DWORD PandaJ2534Device::msg_tx_thread() {
- const HANDLE subscriptions[] = { this->flow_control_wakeup_event, this->thread_kill_event };
- DWORD sleepDuration = INFINITE;
- while (TRUE) {
- DWORD res = WaitForMultipleObjects(2, subscriptions, FALSE, sleepDuration);
- if (res == WAIT_OBJECT_0 + 1) return 0;
- if (res != WAIT_OBJECT_0 && res != WAIT_TIMEOUT) {
- printf("Got an unexpected wait result in flow_control_write_thread. Res: %d; GetLastError: %d\n. Terminating thread.", res, GetLastError());
- return 0;
- }
- ResetEvent(this->flow_control_wakeup_event);
-
- while (TRUE) {
- synchronized(task_queue_mutex) { //implemented with for loop. Consumes breaks.
- if (this->task_queue.size() == 0) {
- sleepDuration = INFINITE;
- goto break_flow_ctrl_loop;
- }
- if (std::chrono::steady_clock::now() >= this->task_queue.front()->expire) {
- auto task = this->task_queue.front(); //Get the scheduled tx record.
- this->task_queue.pop_front();
- task->execute();
- } else { //Ran out of things that need to be sent now. Sleep!
- auto time_diff = std::chrono::duration_cast
- (this->task_queue.front()->expire - std::chrono::steady_clock::now());
- sleepDuration = max(1, time_diff.count());
- goto break_flow_ctrl_loop;
- }
- }
- }
- break_flow_ctrl_loop:
- continue;
- }
- return 0;
-}
-
-//Place the Action in the task queue based on the Action's expiration time,
-//then signal the thread that processes actions.
-void PandaJ2534Device::insertActionIntoTaskList(std::shared_ptr action) {
- synchronized(task_queue_mutex) {
- auto iter = this->task_queue.begin();
- for (; iter != this->task_queue.end(); iter++) {
- if (action->expire < (*iter)->expire) break;
- }
- this->task_queue.insert(iter, action);
- }
- SetEvent(this->flow_control_wakeup_event);
-}
-
-void PandaJ2534Device::scheduleAction(std::shared_ptr msg, BOOL startdelayed) {
- if(startdelayed)
- msg->scheduleImmediateDelay();
- else
- msg->scheduleImmediate();
- this->insertActionIntoTaskList(msg);
-}
-
-void PandaJ2534Device::registerConnectionTx(std::shared_ptr conn) {
- synchronized(connTXSet_mutex) {
- auto ret = this->ConnTxSet.insert(conn);
- if (ret.second == FALSE) return; //Conn already exists.
- this->scheduleAction(conn->txbuff.front());
- }
-}
-
-void PandaJ2534Device::unstallConnectionTx(std::shared_ptr 
-
-