* hyundai WIP
* steer_driver_factor is 1
* removed unnecessary file
* removed unnecessary code
* Update carcontroller.py
bug fix
* safety tuning and fixed interface stiffness
* better lateral tuning, some fixes
* Fix set speed
* added camera state reading, autoresume from stop, cancel on accel, hud alerts
* WIP
* Updated for Kia Sorento *WIP*
* Cleanup
* clean2
* Bug Fixes
* pre-merge
* Add all the cars!
* Panda to auto-detect Camera Bus
* Move Checksum Check
* Final Sorento Tuning
* Make CAN3 for Cam default
* Update README.md
* update panda, minor aesthetic updates
* few other minor changes
* added steer not allowed alert
* bup panda version to force panda update
* fixed camera alerts
* Revert to using CLU15 for Gear Selection
* Missing Defines
Didn’t realise this was removed as well!
* Change Gear Selection Definitions
Add logic to use transmission message rather than cluster message for all gear selections UNLESS the car in question does not have the known good transmission messages
* Revert Camera CAN Bus
* self.candidate
* fixed fingerpint, tested on Sorento
* Update for Elantra on Hyundai-Dev Branch
Latest Elantra values that correlate to progress Community branch.
* Revert 0.5.4 changes for GM for 18ers
* Redo the refactor of stock control msgs
* Fixed missing CONTROL_MSGS -> STOCK_CONTROL_MSGS
* Remove spacing
* Need candidate array idx
* hyundai WIP
* steer_driver_factor is 1
* removed unnecessary file
* removed unnecessary code
* Update carcontroller.py
bug fix
* safety tuning and fixed interface stiffness
* better lateral tuning, some fixes
* Fix set speed
* added camera state reading, autoresume from stop, cancel on accel, hud alerts
* WIP
* Updated for Kia Sorento *WIP*
* Cleanup
* clean2
* Bug Fixes
* pre-merge
* Add all the cars!
* Panda to auto-detect Camera Bus
* Move Checksum Check
* Final Sorento Tuning
* Make CAN3 for Cam default
* Update README.md
* update panda, minor aesthetic updates
* few other minor changes
* added steer not allowed alert
* bup panda version to force panda update
* fixed camera alerts
* Trying to make Highlander ICE stop and go
* Making acceleration slow for fuel efficiency
* Removing annoying commanded disengage beep
* Raised accel_max by 50% and commented on chime
* Testing if Highlander ICE can resume follow from 0
* Returned to 1.5 m/s2 for testing stop and go
* Prep for merging upstream
* Prep for upstream merge item #2
* Added Highlander ICE/Hybrid to Stop and Go
Also updated table of vehicles
* Rollback advertising stop and go for Highlanders
* Fix whitespace
In 2017 Volts, PCM fault occurs for a few seconds if ACC gas
is commanded while user presses gas pedal. PID winds up,
and when PCM fault clears, car gets a "max gas" jolt.
In 2018 Volts, PCM fault doesn't time out, which means pre-enable
doesn't work at all, and car would slowly decelerate, while openpilot
thinks it's engaged.
* Honda Odyssey 2019 EX-L PID Tuning.
* Update interface.py - Increased Kp for Odyssey
Increases response from 0.4, but oscillation still occurs in very sharp curves.
* Move vehicle state values (that get sent to radar) into values.py file, its a better place for it :)
* idx with offset should only be applied to 0x300
* Adds new honda pilot to vehicle state msg array
* Adds Joel's Changes to values, sorted as Rick wanted.
* Adds space at end of file.
* Adds Changes to Steering Ratio for Pilot testing.
* Adding this to steer ratio makes it even 3.33
Not sure if this should go into this PR though or not.
This makes the ratio match the other vehicles in the file. Otherwise it's 3.454545...
* Changes the RAV4 back to not include pedal.
* Updated Comments for Pedal Support
* - Adds menuever test output to gitignore.
- Slight comment update to Ridgeline
* - Cleanup steer status comments
- Adds steering warning for interceptor cars in low speed lockout.
* Cleans up comments.
* Update README.md
* Corrects verbiage in README regarding Comma Pedal on Honda's
* Updates Odyssey and MDX to not add extra warnings for low-speed-lockout.
* Updates Comma Pedal references to use anchor links.
* Minor tweak to README
* Updates RDX to warn no steering below 12mph
* Reverts changes to README, carstate.py, and interface.py
* Removes extra libraries from a prior experiment.
* Replaces README with one from current devel. Hope this fixes spacing issues.
* Adds Pedal back to Honda Cars and sorts fingerprint values
* Fixes spacing changes that were not intentional.
* Fixed carstate no newline at end of file.
* Fixes new line at end of file issue.
* Converted the Long's to Int's
* Adds Honda Ridgeline
Replaced trim level placeholder
Adding 0x301 ridgeline message
(I restructured this slightly since we don't need to repeat `commands.append(make_can_msg(0x300, msg_0x300, idx, 1))` so many times
Updated dbc name
Use pedal_gas to detect gas pressed
Remove unnecessary signal check
Fix array notation
* Tire stiffness factor bumped to 1.5x
* Adds safety tests at line 133
* Revert "Adds safety tests at line 133"
This reverts commit 349edf5b1a879cac704db3786d0626211497bcb7.
* fix failing build due to syntax
* update variables for failing build
* Update interface.py
* Update Tire Slip Factor
* Interpolate ki/kp for steering PID loop
Very much needed for the Volt port: car ping-pongs with low kp
on high speeeds, and the loop is unstable with high kp on
low speeds.
Also, removes "number or array?" logic from PIController,
now that all the callers use interpolation ofr ki/kp.
* Pass speed to steering PID loop for ki/kp interpolation
* Remove unused numbers import
Andrew Frahn
Vasily Tarasov
Jamezz
Vehicle Researcher
wocsor
Ted Slesinski
zeeexsixare
tentious
Joshua F. Rountree
AlexMcInerney
dekerr
Ted Slesinski
rbiasini
Willem Melching
vanillagorillaa
George Hotz