* put gm camera voacc behind disable radar toggle
* bump panda
* bump panda
* bump panda
* experimental long
* fixes
* car control notes and fixes for Bolt EUV
* might enable stop and go
* consistent name
* min enable speed seems to be around 5 kph
* camera acc can engage under 5 kph if stopped
* comment
* comment
* remove this for now
* only real brake
* comments
* update max brake
* bump
* clean up/fix
* same if
* simplify
* fix
* old comment
* no brake_pressed
* temporary fault fix
* tune longitudinal
* update docs
* bump panda
* GM camera ACC cars have no regen in ACC
* cleaner
* cleaner
* fix
* set max gas
* fixes
* fix LKAS unavailable warning from camera
* only camera
* bump panda
* bump panda
* bump panda
* bump panda
* clean up gmcan
* clean up CC
* flip
* rm
* rm comment
* clean up
* custom starting/stopping probably not needed
* Update selfdrive/car/gm/carcontroller.py
* fix crash
* long tuning
* we need long control state to resume
* CAMERA_ACC_CAR not needed
* no interp on accel
* tuning
* formatting
* formatting
* formatting
* formatting
* formatting
* no need to init ccp
* makes more sense now
old-commit-hash: 2fb7b4ffad
* add all signals
* try to forward this PSCMStatus
* fixes
* see if this works
* modify checksum when bit flipped
* bump opendbc
* so i can test without restarting
* bump
* bump panda
* clean up
* comment
* also fix this
* bump
* bump
* every 5 seconds
* only send our values
* fix
* try sending everything again (+1 counter)
* revert
* revert, forward msg
* forward
* fix that
* bump panda
* bump panda
* fine to not copy
* after cancel, pass bus
* fix
* Revert "fine to not copy"
This reverts commit 654ac1a7da.
old-commit-hash: 63d552cafc
* Switch to ECMPRDNL2 for GM gear
* Removing manumatic gear #
* values.py almost complete
* Silverado and Bolt EUV val and CP
* GM controller updated
* Cam hrns supp done (in theory)
* cleanup for new cars
* Remove extra constant
* WS, etc cleanup
* removing the unused
* Fix kpBP typo
* Updated docs
* Skip's PIF tune
* Dropped LKA CAN error patch
* Add silverado sigmoid ff
* CAN Err & LKA latch patch
* Remove EPS fault fix (another PR)
* Remove Silverado (another PR)
* clean up some common params
* Remove Escalade FP
Remove Escalade FP
* comment
* Premier is just a trim
Premier is just a trim
Premier is just a trim
* no footnote: new Bolt is like most other cars, older GM were outliers not at the camera
* clean up
clean up
* bump panda
* bump panda
* bump panda
* bump panda
* bump panda
* remove comments
* try spamming buttons on bus 2
* bump panda
* bumping opendbc w btn rc
* not needed for this port
This reverts commit 6af1f0ba79.
* add button safety
* Send next rc when spamming btns
* forward other signals in message
* missing DriveModeButton
* fill cruiseState.speed
* see if resume works without counter
* try the whole message
* send immediately and at 10Hz
* no resume, back to just button signal
* even holding random buttons it cancels
* Use torque controller with base tune
* stock long GM don't auto-resume yet
* Testing GM zero min steer speed
* Revert latcontrol
* revert opendbc
* latActive is basically lkas_enabled
* Update Bolt torque params
* comment
* clean up
* Add to releases
* Add test route
* Don't specify segment
* bump panda
* bump panda
* no harness for Bolt just yet
* Apply suggestions from code review
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
* We support all and 2023
* move safetyParam up to first cam check
* Bump panda and update docs
* Update RELEASES.md
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
Co-authored-by: Shane Smiskol <shane@smiskol.com>
Co-authored-by: Adeeb Shihadeh <adeebshihadeh@gmail.com>
old-commit-hash: 4ffe9e68db
* Resume Required Alert should be triggered off of ECM state
On GM cars the ECM goes into cruise state 4 (standstill) and in order
for the ECM to accept cruise inputs, the resume button must be pressed
to drive it to state 1 (active).
Previously rather than testing for if the ECM was in state 4, the wheel
speed sensors were checked that the vehicle was going less than 0.5 m/s.
In some cases this could cause the resume required alert to be displayed
before the car actually came to a stop as far as the ECM was concerned.
If the alert is triggered before state 4 and OP demands acceleration,
its possible for OP to acelerate while the Resume Required Alert is
displayed created a very confusing UX.
* After more review, the problem was actually with the 'if at_full_stop' check was inside an else statement preventing entering the stopped mode if braking is 0
old-commit-hash: 4b12aca941
* Change dashboard command of GM to use packer
Also, separate "follow distance" from "engaged".
* Fix dashboard setSpeed scaling
old-commit-hash: 012727ef60
Adeeb Shihadeh
Shane Smiskol
Jason Shuler
andrewcopenpilot
Adeeb Shihadeh
Kishan Karunaratne
Adeeb
George Hotz
Vehicle Researcher
Vasily Tarasov
Jamezz